Question about 1995 Toyota Camry

Open Question

How to remove power steering pressure hose for 1994 camry v6

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: power steering belt on a 94 camry v6

only 2 bolts. They are hard to get to at the back of the engine but one is the mounting one and the other is the locking one for the adjuster once you get them lose you can undo the adjuster bolt and take tension off of belt then pull it off and replace it.

Posted on Aug 05, 2009

Ad

SOURCE: Hello, i need to replace a high pressure power steering hos

The high pressure hose is simple to replace if its not to confined of an area for you. Just un-thread from both sides, fill with power steering fluid, work steering wheel from side to side to work the air out. In between this check fluid levels. If air is still in it will make a whining sound, and bubbles will be visible in the power steering fluid reservoir. Hope I helped you good luck!!

Posted on Jul 11, 2010

  • 2187 Answers

SOURCE: Need to change power steering hose

it is a big job since you need ro crimp the hoses properly. I would recommend to send this to a specialist since improper fittings would mean leakage or contamination of the fluids which may lead to loss of pressure, damage or accidents.

Posted on Jul 16, 2010

subikid90
  • 180 Answers

SOURCE: 92 toyota camry v6 xle shakes/vibrates over 55mph

Sounds like wheel bearings are going out.

Posted on Nov 15, 2010

SOURCE: Where is the power steering temperature sensor on 1993 Toyota Camry v6

IM DRiving my parents car, a fair time ago they replaced the temp sensor, because the engine would not go to top gear. this can be tested by pressing the O/D Off button while driving at highway speeds and if the car changes gears its ok.

Posted on Aug 21, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove a power steering pressure hose on a 1999 Mercury Sable


You have to discon the battery cable before you start. Remove the coolant expansion tank. Remove the drivebelt and alternator if you have an OHV V6. Raise the vehicle on jack stands. Place a drain pan below the pump. From below, remove the splash shield and discon any brackets or ties that hold the hose to the body. After draining, you may have to replace the pwr steering fluid filter, located in the fluid line, then replace the fluid. A crows-foot wrench may be necessary to remove some hose fittings. This is a job for a mechanic with a power lift to be honest. Whatever you do, be careful not to contaminate the power steering fluid. Bleed the system after replacing the hose. The pressure hose is held in place by threads and not a clamp as the other hose has. Get yourself the Haynes repair manual 36075 '96 thru 2005 Ford Taurus & Merc Sable. It has a detailed step by step description of this procedure. Good Luck

Dec 28, 2014 | 1999 Mercury Sable

1 Answer

Show how to replace a power steering pressure hose on a 1993 toyota camry


clamp in the flow direction loosen old pipe gently then completely remove,MAKE SURE ALL CONNECTIONS ARE SPOTLESSLY CLEAN,REPLACE THE OLD PIPE RELENISH THE TANK,MOVE STEERING TO THE LEFT & TO THE RIGHT A COUPLE OF TIMES TO DISPELL AIR,CHECK FOR LEAKS,TOP UP IF NEEDED OVER TOPING IS AS BAD AS UNDER TOPPING

Oct 03, 2012 | 1993 Toyota Camry V6

2 Answers

Where is the power steering temperature sensor on 1993 Toyota Camry v6


On some Camrys the radiator fan is run by hydraulic pressure from the power steering pump. I think the sensor you mention is the engine coolant temperature sensor, which is in the circuit which operates the fan when the engine becomes hot. If this fails the engine will overheat, yes. The fan does not cool the hydraulic fluid from the pump.

If your power steering fluid gets low the same thing can happen, but you would notice immediately as the steering would become intermittently harder.

Jan 02, 2012 | 1993 Toyota Camry V6

1 Answer

How to replace high pressure hose on a 1994 Silverado Chevrolet pick up truck.


hmmm..which high pressure hose the a/c or power steering hose...if its the a/c u need to take this to a service center. removing the high pressure hose without recovering the freon can cause serious injury.it is under extreme high pressure at all times even when the truck is not running... if its the power steering hose then start by removing the plastic shield in the steering staft at the steering box on the drivers side frame loosen the 18mm line nut then follow it to the other line nut on the back of the power steering pump....but sometimes the pump may need to be removed to to this, if this is the case i recommend u take it to a service center

Jul 12, 2011 | Chevrolet Silverado Cars & Trucks

1 Answer

Where is the camshaft sensor located on a 1994 pontiac grand am 3100 v6


the camshaft sensor is located under the power steering pump on the 3.1, remove pump not the hoses. just set it aside. now you can see sensor, remove the holddown bolt and remove sensor!! good-luck!

Oct 04, 2010 | 1994 Pontiac Grand Am

1 Answer

Power steering leak


Check power steering hose

Jul 25, 2010 | 1993 Toyota Camry V6

1 Answer

Power sterring in 1992 toyota camry


oil level in tank too low so air getting into system,the pump not generating the pressure.the seals on the rams worn the steering colum plate which moves the pump activaters

Jun 26, 2010 | 1992 Toyota Camry V6

1 Answer

Need to remove power steering pump


1. Take off the battery black-cable (negative cable).
2. Drain out the power-steering reservior.
3. Place a large container under the car to catch excess fluid. Disconnect the power-steering hoses.
4. Remove the right front wheel, and support the car on jack-stands.
5. Remove the apron fender under the right front-wheel
6. Disconnect and loosen the clamp and the fluid return hose from the pump.
7. Remove the pressure line-to-pump union bolt. Push this away from the pump. Remove the sealing washers on both sides of the fitting.
8. Remove the pivot bolts and the drive-belt.
9. Remove the adjuster, mounting bolts, pivot and take-out the pump.
10. Installation is opposite of removal.

Nov 14, 2009 | 1992 Toyota Camry V6

1 Answer

Need to replace high pressure power steering hose on 2004 Monte Carlo SS. Need tips to effectively do the job myself. Tools needed, tricks to make the job easier, what not to do...etc. Thank yiou so much...


Power Steering Line/Hose: Service and Repair
Pressure Hose
Power Steering Pressure Pipe/Hose Replacement (3.8L)
Removal Procedure
1. Place a drain pan under the vehicle.
2. Remove the accessory drive belt.
3. Raise and support the vehicle. Refer to Vehicle Lifting.
4. Remove the tire and wheel assembly.
5. The power steering pressure hose is the lower hose at the power steering gear.
Remove the power steering pressure hose from the power steering gear.
6. Remove the power steering pressure hose from the power steering pump.
7. Remove the power steering pressure hose from the clamps on the power steering gear.
8. Remove the power steering pressure hose from the vehicle.
Installation Procedure
1. Install the power steering pressure hose to the vehicle.
2. Install the power steering pressure hose to the clamps on the power steering gear.
Notice: Refer to Fastener Notice in Service Precautions.
3. Install the power steering pressure hose to the power steering pump.
^ Tighten the fitting to 27 Nm (20 ft. lbs.).
4. Install the power steering pressure hose to the power steering gear.
^ Tighten the pressure hose fitting to 27 Nm (20 ft. lbs.).
5. Install the tire and wheel assembly.
6. Remove the drain pan from under the vehicle.
7. Lower the vehicle.
8. Install the accessory drive belt.
9. Fill the power steering system with power steering fluid.
10. Bleed the power steering system.
11. Inspect the power steering system for leaks.

00d203e.jpg

Sep 15, 2009 | 2004 Chevrolet Monte Carlo

2 Answers

How to replace power steering pump


2004 Pontiac Grand Prix V6-3.8L VIN 2

Power Steering Pump: Service and Repair
Power Steering Pump Replacement
NOTE: The content of this article / image reflects the changes called out by TSB: 05-02-32-004.

Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.

d2ff628.jpg
949e18c.jpg
a9ee201.jpg

Sep 07, 2009 | 2004 Pontiac Grand Prix

Not finding what you are looking for?
1995 Toyota Camry Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8518 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...