Question about 2004 Dodge Stratus

Open Question

Where is the crankshaft sensor in the 2003 Chrysler voyager 2.4 engine

Posted by Anonymous on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75051 Answers

SOURCE: were is the crankshaft position sensor located on

ANSWER: CRANKSHAFT POSITION SENSOR - 4.7L V-8 ENGINE
REMOVAL
The Crankshaft Position (CKP) sensor is located at the right-rear side of the engine cylinder block CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine the cranks sensor is positioned and bolted into a machined hole in the engine block

Disconnect CKP electrical connector at sensor.
Remove CKP mounting bolt CKP Sensor Location/Removal/Installation - 4.7L V - 8 Engine
Carefully pry sensor from cylinder block in a rocking action with two small screwdrivers.
Remove sensor from vehicle.
Check condition of sensor o-ring.
INSTALLATION
Clean out machined hole in engine block.
Apply a small amount of engine oil to sensor o-ring.
Install sensor into engine block with a slight rocking action. Do not twist sensor into position as damage to o-ring may result
CAUTION: Before tightening sensor mounting bolt, be sure sensor is completely flush to cylinder block. If sensor is not flush, damage to sensor mounting tang may result.

Install mounting bolt and tighten to 28 N·m (21 ft. lbs.) torque.
Connect electrical connector to sensor.

Posted on Jun 29, 2010

ZJLimited
  • 17970 Answers

SOURCE: where is the crankshaft position sensor on a 2003 dodge caravan 33L V6 engine

Hi there:
The 3.3/3.8L crankshaft sensor is located on the rear of the transmission housing, above the differential housing (The bottom of the sensor is positioned next to the drive plate...




8_21_2012_9_41_28_pm.gif

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Posted on Aug 21, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crankshaft position sensor 2000 crysler voyager 2.4L


10_14_2011_2_00_35_pm.gif
https://www.google.ca/search?q=Where+is+the+crankshaft+position+sensor+2000+chrysler+voyager+2.4L&hl=en&source=lnms&tbm=isch&sa=X&ei=2J82UamUKsPWygHQyoCoBg&sqi=2&ved=0CAcQ_AUoAQ&biw=1366&bih=667#imgrc=CCm04tc9Q6spXM%3A%3BZMusm8em5DHqxM%3Bhttp%253A%252F%252Fc.fixya.net%252Ffixya20%252Fuploads%252Fimages%252F10_14_2011_2_00_35_pm.gif%3Bhttp%253A%252F%252Fwww.fixya.com%252Fcars%252Ft10666937-want_change_oil_ina_2_4_l_chrysler%3B309%3B300

Mar 06, 2013 | 2000 Chrysler Grand Voyager

1 Answer

I have a 2001 chrysler voyager with a 2.4l engine. it cranks but no start. no check engine light


From a(Retired Chrysler Tech) If prior to changing the T-stat & belts you were experincing a no start,Then afterward it started & ran fine until you again worked in the same area as before, The first thing I would do is to check any and all electrical "wiring" and or sensors & switches in that same area, If your vehicle is equiped with a crankshaft sensor it may be at the front of the engine in close proximity to the harmonic balancer,"crankshaft pully"& the wiring my be routed as to be easily moved while working in the belt area..pay close attention to the condition of the wiring. any wires that are exposed(bare) must be repaired or replaced. check for loose plugs at sensors. Be meticulous in your search, the smallest thing will create a no start in this type of set up.

Dec 15, 2012 | 2001 Chrysler Voyager

1 Answer

Want to change oil ina 2.4 L. chrysler Voyager but can't find the oil filter.Where is it located?


On 4-cylinder engines, the crankshaft position sensor is mounted to the engine block behind the alternator, just above the oil filter, try to cocated previously this to find the filter, according with the next images...


10_14_2011_2_00_13_pm.gif

10_14_2011_2_00_35_pm.gif

10_14_2011_2_00_56_pm.gif


Hope this helps; thank you for using Fixya (dont forgetted to rating this answer).

Oct 14, 2011 | 2000 Chrysler Grand Voyager

1 Answer

Where is the fuse box located in a 2003 chrysler voyager?


Hi I a 2003 Chrysler Voyager with a 3.3L V6 Engine. If you open up the hood the fuse box is located on the right side of the vehicle it is a rectangular black box.

Mar 06, 2011 | 2003 Chrysler Voyager

1 Answer

I have 2.4 engine and it wont start, i have replaced the crankshaft sensor.what is the probem


have you checked the cam shaft sensor?
do you have fuel getting to the motor?

get a spark tester, and see if you have spark

Aug 10, 2010 | 2003 Chrysler Voyager

1 Answer

Where is the crankshaft position sensor on a 2003 chrysler concord lxi


Its located on the passenger side of the engine,back side of engine mounted in the back of the block above the flywheel.

Feb 06, 2010 | 2003 Chrysler Concorde

Not finding what you are looking for?
2004 Dodge Stratus Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7726 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...