Question about 2007 Toyota 4Runner

Open Question

How to install replace turn signal 2007 Toyota 4Runner?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: Removing and replacing stock radio on Toyota 4runner 03

crutchfield.com is easiest way.also will allow you to leave the factory harness intact.

Posted on Jun 08, 2009

Ad
  • 7353 Answers

SOURCE: 1997 toyota 4runner left turn signal indicator is

You have a bad ground, take the light out and see if there are ground wires at each bulb socket, these will get loose or corrode.

Posted on Mar 13, 2010

ZJLimited
  • 17970 Answers

SOURCE: Replacing heater core in a 1995 Toyota 4Runner

The heater core is a small heat exchanger located inside the truck, similar to the radiator at the front of the truck. Coolant is circulated from the engine through the heater core and back to the engine. The heater fan blows fresh, outside air through the heater core; the air is heated and sent on to the interior of the truck. For Toyota Pick-ups/Land Cruiser/4Runner 1989-1996 check this reference repair guide...



Heater Core - REMOVAL & INSTALLATION
(see Figure 1)

  1. Drain the cooling system.
  2. Remove the heater unit assembly. Have alot of towels handy for the leakage of coolant that may spill into your interior.
  3. Remove the fasteners securing the core to the unit, remove the plates and clamps. Pull upwards to remove the core from the unit.
To install:
  1. Inspect the core fins for any blockage. Using compressed air, clean them.
  2. Install the core into the unit placing the plates and clamps into position. Tighten the core screws.
  3. Install the heater unit into the vehicle.
  4. Fill the cooling system.
85a96e3.jpg

Fig. 1: Exploded view of the heater unit assembly-1996 4Runner shown





Heater Unit - REMOVAL & INSTALLATION
(see Figure 1)

Have alot of towels handy for the leakage of coolant that may spill into your interior.
  1. Discharge the A/C system (if applicable), using an approved recovery/recycling machine.
  2. Remove the cooling unit (if applicable).
  3. Drain the cooling system.
CAUTION When draining engine coolant, keep in mind that cats and dogs are attracted to ethylene glycol antifreeze and could drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain coolant into a sealable container. Coolant should be reused unless it is contaminated or is several years old.
  1. Disconnect the hoses to the heater core. Tag each one so that it may be correctly reinstalled.
  2. On some models you will need to remove the glove box assembly. On others, the instrument panel and reinforcement.
  3. At the heater case under the dash, disconnect the ductwork from the case.
  4. Disconnect the heater control cables from the heater case. Lift the spring clip holding the control cable to allow the cable to be manipulated. Don't deform or crimp the cables.
  1. Disconnect the wiring harness to the blower fan.
  2. Remove the three or four bolts holding the heater case to the dash. Because the inlet tubes project through the firewall, the unit will not fall straight down. It will need to be pulled into the passenger compartment and then brought downward.
To install:
  1. Lift the case into position and carefully place the inlet and outlet pipes through the firewall. Install the retaining bolts holding the case to the dash.
  2. Connect the wiring harness to the blower fan.
  3. Connect the control cables to their linkages. Each must be adjusted so that the motion of the dashboard lever causes the correct corresponding motion in the air door. Both the control lever and the door must reach maximum travel at the same time if full function is to be achieved.
    1. Set the dashboard control to FRESH. Lift the adjustment clip and adjust the air inlet cable towards the heater unit until the linkage is at its maximum travel on Pick-Up and 4Runner. For Land Cruiser, adjust the cable away from the case. Release the adjustment clip.
    2. Set the dashboard control to VENT (Pick-Up) or DEF (4Runner and Land Cruiser). Lift the adjustment clip and adjust the air flow control cable towards the heater unit until the linkage is at its maximum travel. Release the adjustment clip.
    3. Set the temperature control to COOL. Lift the adjustment clip and adjust the air mix control damper control cable away from the heater case until the linkage is at its maximum travel on . For Land Cruiser, adjust the cable towards the case.
  4. Connect or reinstall the ductwork. Make certain each tube is firmly and completely fitted on its port. A light spray of glass cleaner serves as a good lubricant; don't use too much.
  5. Install the glove box and/or instrument panel assembly.
  6. Connect the heater hoses. Use new clamps.
  7. Install the cooling unit (if equipped).
  8. Refill the coolant, then charge the A/C system (if equipped).



Hope this help (remember comment and rated this).

Posted on Aug 02, 2010

  • 6 Answers

SOURCE: replacing front turn signal light bulb on 2006

You have to crawl under the car to get this done. Identify the location of the bulb then crawl underneath and locate the appropriate connector. Grab the connector with your hand and twist the connector right-to-left. The connector will then disengage from the plastic housing and you can withdraw the connector and the bulb from the housing. Once disconnected, grab the bulb with one hand and the connector with the other, and pull out the bulb straight out (no twisting). Replace is the reverse. Easy. Should take less than 1 minute.

Posted on Jun 27, 2011

suarezelec20
  • 259 Answers

SOURCE: Will the tailgate from a 1995 Toyota 4Runner fit a 1997 Toyota 4Runner?

Measure them is the best bet. If you don't have a tailgate on your 97 measure across (length) then measure from the bottom of your bed to the top (width)

Posted on Sep 24, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1998 Toyota 4runner turn signal and hazard light not working. Changed the fuses relay and flashers. Still doesn't work


Check all the turn signal bulbs. Check their sockets for corrosion. Look for damaged wires going to the sockets. Make sure you have the correct bulbs.

Feb 26, 2015 | 1998 Toyota 4Runner

1 Answer

Replace hatch opener


You need to remove the vinel panel from the rear hatch.Peal back plastic from access hole. Remove 4 hexnuts that hold the tag light , hatch switch and window controller assemply in place.Pop loose assembly from hatch, remove 2pl head screws that hold opner switch to assembly didconect wireing conector. install new switch.

Aug 25, 2012 | 2007 Toyota 4Runner

1 Answer

4runner flasher not working


the bulb has 2 fillaments and one is burnt out replace the bulb

Jul 26, 2012 | 2007 Toyota 4Runner

2 Answers

When I hook up my trailer to my 1996 4Runner both turn signal lights come on at the same time. When we unplug the trailer and connect two lights directly to the factory trailer wires on the rear of...


You likely need diode isolators on the turn signal wiring on the trailer, or on vehicle side connector. Your local auto parts store should have what you need, and show you how to install them.

Aug 25, 2009 | 1996 Toyota 4Runner

1 Answer

How to replace a fog lamp with replacement bulb only on 2002 toyota 4runner sport edition???? the three screws on the bottom?


Well, these are the steps and I will post the pic here in a second...looks like 2 screws...but like I said, you can see the picture for direction on this.


Remove or disconnect the following:

Front turn signal lamp
  • Connector
  • 2 screws
  • 2 claw fittings
  • Fog lamp assembly
  • Fog lamp bulb as shown
  • Fog light unit

  • To Install
    1. Install or connect the following:
      • Fog light unit
      • Fog lamp bulb as shown
      • Fog lamp assembly latch the 2 claw fittings and 2 screws
      • Connector
      • Front turn signal lamp
    Trying to post the pics now....

    May 14, 2009 | 2002 Toyota 4Runner

    1 Answer

    1996 4runner Front Turn signal failure


    the problem might be a flasher unit. try to replace it

    Apr 03, 2009 | 1996 Toyota 4Runner

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    40 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Toyota Experts

    yadayada
    yadayada

    Level 3 Expert

    76848 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8582 Answers

    Are you a Toyota Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...