Question about Cars & Trucks

Open Question

Telsta boom truck , boom stuck in raised position , how can I lower it manually???

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 3113 Answers

SOURCE: Power windows not working properly 2000 Buick Century

Replace the window regulators.

Posted on Jul 17, 2009


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Drivers side window will not go completely airtight when up.drops and goes up when door opens and shuts, but not high enough to seal correctly

My 02 had this same problem, the glass has shifted position in the mechanism. You will need to take the inner door card off to get at the mechanism, lower the glass about half way then reach through the large opening in the door panel to feel for the large 'cog' shaped retaining bolts that hold the glass to the mechanism (one either side, both facing the outer door skin). A 5mm torx or allen key bit is required to loosen both 'cogs'. You can then adjust the glass position. This is possibly best done with two people...once the glass is loose, make sure you move the glass first to break the seal (it may have stuck to the rubber seal over time, so will not move much), then gently tighten into place, raise the window to the full up position, shut the door fully, then with the help of an assistant, one inside the car one outside, move the glass into the desired place and tighten the cogs. Open the door, fully lower and fully raise the glass, then keep the switch in the up position for 5 seconds, this teaches the ECU the new position. Check that the window closes when you open and close the door, if not, try adjusting the glass angle with the adjustment screws located at the very bottom of the door. When in the right position, you should just be able to pull a sheet of paper past the glass and the seal. Boom, done!

Sep 30, 2016 | 2004 Mini Cooper

1 Answer

The dig boom will not raise or lower on a 1020 walk behind trencher

Craig, I do not have a lot of experience with trenchers, if hydraulic operated not enough oil/check reservoir,, one of the valves/controls may be stuck, you will have to follow line from boom cylinder and trace it back to the valve and dismantle and repair. Secure boom as to not harm you or others.
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

Apr 13, 2016 | Cars & Trucks

1 Answer

What is the correct relay solenoid for an electric motor that runs the hydraulic pump for a Telsta A-28D aerial boom lift ?

TELSTA A28D Bucket Controls Acting Up - Contractor Talk > Forum > Equipment & Safety > Vehicles
Sep 5, 2009 - 20 posts - ‎9 authors Problem I'm having with my truck is that the controls on the boom are acting .... I'd also like to replace the 3 small relays in the main control panel where the boom ... We recently purchased a 2000 e350 with the Telsta A28D lift and had .... back to the tower and up to the controls back down to the solenoids.

Jul 25, 2015 | Cars & Trucks

1 Answer

Safty on skidsteer

Two possibilities: your machine is designed to prevent startup with boom up.
Safety switch is stuck or out of adjustment. I rewired mine with a toggle switch to bypass the saftey

Jan 29, 2015 | Seat Cars & Trucks

1 Answer

Ford telsta 1995

Check with your local library. They carry Haynes and Chilton's service manuals for most cars and have accounts that will get you online access to their amauals as well, but you can only acess them at the library computers.

Aug 08, 2014 | 1995 Ford Contour

1 Answer

It a bucket truck with a telsta boom

the regulator is built in the alternator

May 06, 2009 | Ford F-450 Cars & Trucks

1 Answer

Power window broke, stuck up need temporaily lower then back up

you can disconnect the motor and the gear and the window should slide down.. if you can't access that.. you can force the gears to turn

Apr 05, 2009 | 1999 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

36 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13614 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides