Question about Cars & Trucks

Open Question

Engine torque specs for cummins 8.3l isc - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
johnny5846
  • 379 Answers

SOURCE: Looking for the torque specs for 1998 chevy astro van?

1998 chevy astro 4.3 v6 torque specs include :
* foot pounds *
balance shaft (if equiped) gear bolt = step 1 = 15 ft.lbs. step2 = additional 35 degrees.
camshaft sprocket bolt = 18 ft. lbs.
connecting rod cap = step 1 = 20 ft. lbs. step 2 = additional 70 degrees.
crankshaft damper bolt = 74 ft. lbs.
crankshaft oil deflectorbolt/nut = 27 ft.lbs.
cylinder head bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees. (tighten in sequence)
2811243.jpg


exhaust manifold bolts = step 1 = 11 ft. lbs. step 2 = 22 ft. lbs.
flywheel bolt = 74 ft. lbs.
main bearing cap bolts = step 1 = 15 ft. lbs. step 2 = additional 73 degrees.
oil filter adapter bolt = 15 ft. lbs.
oil pan bolt/nut = 18 ft. lbs.
oil pump bolt = 66 ft. lbs.
rocker arm with press in studs = 18 ft. lbs.
rocker arm with screw in studs = 19 ft. lbs.
valve lifter retainer bolt = 12 ft. lbs.
water pump bolt = 33 ft. lbs.
* inch pounds *
balance shaft retaining plate bolt = 106 in. lbs.
camshaft retainer plate bolt = 106 in. lbs.
front cover bolt = 106 in. lbs.
intake manifold upper = step 1 = 44 in. lbs. step 2 = 88 in. lbs.
intake manifold lower = step 1 = 27 in. lbs. step 2 = 106 in. lbs. step 3 = 133 in. lbs. ** (tighten bolts in sequence)

cbb8861.jpg

thanks for your vote !

Posted on Dec 28, 2008

Ad
GM Elec
  • 1000 Answers

SOURCE: torque specs for 2000 chevy silverado truck 4.3 v-6 engine

Not sure what torque spec's your looking for.
Go to www.AutoZone.com, enter your vehicle information and check specifications. You should be able to look up the torque spec's your looking for.
Good luck.
Regards,

Posted on May 02, 2009

SOURCE: need torque specs for a 85 s10 chevy with a 2.5 engine?

here you go!

1dd4f4a.gif93a64e1.gif

Posted on Jun 21, 2009

  • 5 Answers

SOURCE: Head bolt torque specs?

I really really really hope you turned the bolts an additional 90 degrees after torquing to 22 Ft-lbs. Otherwise, you may be taking that head off again.

Best of luck,

David

Posted on Mar 15, 2010

tburtk
  • 158 Answers

SOURCE: i need torque specs for a 2004 dodge cummins 24

http://www.dieseltruckresource.com/dev/index.php

I suggest this website for your dodge truck needs.

Posted on May 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Fault code 1 Fail 31 Spn1569 2015 Cascadia Cummins engine


spn 1569 relates engine protection torque derate -condition exists.
critical fault codes related to engine operation are active
code 1 means urgent attention
A sort of limp mode setting that requires immediate attention by a cummins service center to prevent further damage to the engine
go google and type in--- cummins engines fault codes (or cummins engine fault code 1569) and there are pages of pdf downloads that list all the codes and what they stand for

Oct 07, 2015 | Cars & Trucks

Tip

CUMMINS ISB DIESEL ENGINES FAULT CODES Cummins ISL & ISC Fault Codes ...


CUMMINS ISB DIESEL ENGINES FAULT CODES
Cummins ISL & ISC Fault Codes
Cummins ISM Fault Codes
Cummins ISX Fault Codes

Source

TRUCK Tractor MANUALS PDF

on Dec 20, 2016 | Cars & Trucks

2 Answers

Idling very high n wont come down. why is that ? after i put a throttle body gasket on.


If you tighten one side down before the other this could be an air leak. Loosen it, snug up one corner, then the opposite corner. Then the rest. The do the same when tightening it done. it only takes about 7 foot pounds to seal these. 7 pounds is done with one hand on a short ratchet.

Jul 26, 2015 | 2000 Jeep Grand Cherokee

1 Answer

I need the torque specs on a rear axle pinion nut for a 2003 Dodge Ram 2500 4/4 Cummins, Automatic.


The pinion nut does not have a torque spec. as in how tight the nut is. The amount of torque is measured in bearing preload. You will need a "torque to rotate" torque wrench. If you are using new bearings the torque spec. is 15-25 in. lbs. If you are using your old bearings the torque spec. is 10-20 in. lbs to rotate. To measure this you will need to tighten the nut in small increments then use the torque to rotate wrench to turn the pinion without the carrier/ ring gear installed. Repeat until desired torque is reached.

Jan 29, 2011 | Dodge Ram 2500 Cars & Trucks

1 Answer

Changed 2 fuel /water filters on a cummins 8,3 isc 350hp ,


use silicone spray it will run on this you have to spray in air inlet hose while someone cranks do this until air is out of system should start running on it own power takes 3-5 min

Jul 18, 2009 | 1988 Dodge D-Series Pickups

2 Answers

My 1995 cougar xr7 stalls when it de-excelerates. Also fails to start after engine is shut off.


idle_air_solenoid_ford.gif

FORD IDLE AIR BYPASS

Ford doesn't use idle air bypass to regulate idle speed on its older throttle body (CFI) applications, but uses a solenoid or vacuum diaphragm instead to open the throttle linkage. Idle air bypass is used only on multipoint injection applications. On older pre-OBD II cars, codes 12, 13, 16, 17 & 19 all indicate idle speed is out of spec (too high or too low). Codes 47 and 48 indicate a fuel mixture problem which could be caused by an air leak. On OBD II vehicles (1996 & newer), codes P505 to P509 indicate a fault with the idle speed control system.

The diagnostic procedure when any of these codes are found is to turn the engine off, unplug the ISC bypass air solenoid connector, then restart the engine to see if the idle rpm drops (it should if the ISC solenoid is working). No change would indicate a problem in the motor or wiring.

The ISC solenoid can be checked by measuring its resistance. With the positive lead of a digital volt/ohm meter on the VPWR pin and the negative lead on the ISC pin, measure the resistance of the solenoid. On many applications, the spec calls for 7.0 to 13.0 ohms. If it is out of specs, the ISC solenoid is bad. Also check for shorts between both ISC solenoid terminals and the case.

If the ISC checks out okay, check for battery voltage between the ISC connector terminals while the key is on. Voltage should also vary when the engine is running. No voltage indicates a wiring or computer problem.

Jul 03, 2009 | 1997 Mercury Cougar XR7

1 Answer

My 97 dodge cummins 3500 shuts off when put in


i have seen the trans torque converter caus e this problem before..torque converter locking up inside stallin engine

Mar 30, 2009 | Dodge Ram Pickup 3500 Cars & Trucks

1 Answer

Water pump replacement procedure 2005 2500 dodge with cummins diesel


take off old water pump. clean up area on the motor real good.do this by using a scrapper and cleaning slolvent. when thats all done put hi temp silicon on the block water pump and the put gasket on silicon. let dry for like five minutes. put in on torque bolts to specs.

Aug 22, 2008 | 2005 Dodge Ram 2500 Truck

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

955 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...