Question about Cars & Trucks

Open Question

How to remove my Bosch 24-CA Clear Advantage Beam Wiper Blade?

Posted by Anonymous on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: rear wiper blade

I went to a Honda dealer and bought a replacement wiper blade (rubber part only) for about $6, and the guy in parts came outside and changed it for me. You slip off the rubber blade only from the wiper assembly and then slip in the new blade.

Posted on Jun 18, 2008

Ad
auditech13
  • 43 Answers

SOURCE: how to remove audi a6 wiper blades

The problem with this wiper blade set up is the slides get jammed up w/ crude.  You should lubricate the slides and they should slide off.  Then carfully lift the arm and remove the blade.  Warning you should never leave the arm in the upright position.  Windshields get cracked this way.  Also note the pivit points the blades attach too.  These will normally sieze up and cause clearing issues even with new blades.  Lubricate these pivit points and use a pair of channel locks to move it back and forth until it will go 360 degrees with your fingers.  Install is in reverse order of removal. 

Posted on May 28, 2009

  • 61 Answers

SOURCE: Remove wiper blade

Do you mean the wiper blade or the wiper arm?

The wiper blade should have a small tab or lever on the underside of the hinge where it attaches to the arm. Use a small screwdriver or a pick (etc..) to gently pry the lever upwards to pull the locking tab out of its corresponding hole on the wiper arm. Once the tab is up, firmly grasp the wiper blade and pull towards the base of the wiper arm. Sometimes they stick a little, just be careful not to bend the wiper arm.
If you are looking to remove the wiper arm, remove the plastic cap at the base of the wiper arm to gain access to the nut below. Using either a 13mm (1/2 inch) or 15mm socket (depending on the model) remove the nut by turning counter-clockwise. Once the nut is off, place your hand in the middle portion of the wiper arm and firmly push downward, being careful not to bend the arm. What you are trying to do is rock the arm off of the wiper motor stud. Be sure to mark where the wiper blade rests on the windshield before removing it, so you can reassemble it in the same spot when you put it back together. Use a grease pencil or something else that you can clean off later.
Hope this helps!

Posted on Jul 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where can we buy replacement blades online?


Amazon.com: Silhouette Replacement Blade

www.amazon.com > ... > Replacement Blades
Amazon.com, Inc.This replacement blade is compatible with all Silhouette electronic cutting tools. .... center" from Silhouette online store) It has taken me 3 blades to get through ...
Windshield Wiper Blades - Advance Auto Partsshop.advanceautoparts.com/c3/windshield-wiper-blades/15566462 results - Save on Windshield Wiper Blades with great deals at Advance Auto Parts. Buy online, pick up in-store in 30 minutes. ... Replacement Parts (460).Wiper Blade (Windshield) at AutoZone.com - Best Wiper ...www.autozone.com/ignition-tune.../wiper-blade-windshieldAutoZoneReplacement Parts ... Vehicle Specific Bosch Evolution/Wiper Blade (Windshield).Price: $15.19. Part Number: 4820; Application: Front; Notes: Beam Design

Nov 02, 2015 | Cars & Trucks

1 Answer

Dodge charger fuse box , where the fog lights relay goes ?Thanks


lx_front_relays.jpg


Cavity/ Fuse /Circuits
1/ 20 Amp Yellow/ Left High Beam Headlight
2/ 20 Amp Yellow/ Right High Beam Headlight
3/ 15 Amp Dk. Blue/ Adjustable Pedal
4/ 20 Amp Yellow/ Horn
5/ 25 Amp Clear/ Headlamp Washer - If Equipped
6/ 15 Amp Dk. Blue/ Front Control Module (FCM)
7/ 20 Amp Yellow/ Fog Lamp
8/ 15 Amp Dk. Blue/ Park Lamp
9/ 15 Amp Dk. Blue/ Non ABS Brakes
10/ 5 Amp Orange/ Starter
11/ 20 Amp Yellow/ Auto Shutdown/Powertrain Control Module (PCM)
12/ - -
13/ - -
14/ 25 Amp Clear/ Powertrain Control Module
15/ 20 Amp Yellow/ Injectors, Ignition Coils
16/ 15 Amp Dk. Blue/ Powertrain Control Module
17/ 30 Amp Pink/ Antilock Brake System (ABS) Valves
18/ 30 Amp Pink/ Windshield Wiper/Washer
19/ 50 Amp Red/ Radiator Fan
20/ 20 Amp Lt. Blue/ Starter
21/ 50 Amp Red/ ABS Pump Motor
22/ 40 Amp Green/ Radiator Fan High/Low
23/ 50 Amp Red/ High Intensity Lighting
24/ - -
25/ 30 Amp Pink/ Lighting Left High Beam/Right Low Beam
26/ 20 Amp Lt. Blue/ Transmission
27/ 30 Amp Pink/ Lighting Left Low Beam/Right High Beam
if this helps please rate 4 thumbs up.

Jan 21, 2011 | 2007 Dodge Charger SRT8 Sedan

1 Answer

How to remove the wiper arm from the shaft so I can remove the cslotted cowl to replace the wiper bushings.


REMOVAL & INSTALLATION
(see Figures 1 and 2)

To remove the arm from the pivot, lift the arm to permit the latch to be pulled out to the holding position and remove the arm from the pivot with a rocking motion.

zjlimited_140.jpg

Fig. 1: Mount the wiper blade/arm as shown-Dakota models

zjlimited_141.jpg

Fig. 2: Mount the wiper blade/arm as shown-1994-96 Pick-ups



When installing the arms, the at-rest position of the blades should be determined before pushing the arm onto the pivot. For Dakota trucks, the tip of the driver's side blade should be 0.51-2.63 in. (13-67mm) above the cowl panel and the passenger's side blade should be 0.94-3.06 in. (24-78mm) above the cowl panel. For 1989-93 Pick-ups and Ramchargers, the driver's side blade should be 1.84 in. (47mm) above the windshield weatherstripping at the heel of the blade; the passenger's side blade should be 2.24 in. (57mm) above the weatherstripping. For 1994-96 Pick-ups, the wiper motor must be in the PARK position and the wiper blade should be about 0.85 in. (22mm) from the upper edge of the black-out areas at the base of the windshield.


Hope this helps to solve it.

Nov 26, 2010 | 1992 Dodge Ram 250

1 Answer

I need to adjust the wiper arm on a 1997 suburban, it hits the side of the window.


Wiper Arm & Blade (Front) Removal & Installation Wiper Blade To Remove:
  1. Turn ignition switch to ACCY position.
  2. Turn wiper switch to PULSE position and turn ignition OFF when wipers are stopped in the innerwipe position.
  3. Push the wiper blade clip button IN and remove wiper blade from wiper arm.
To Install:
  1. Insert wiper arm hook through opening in wiper blade.
  2. Place wiper blade pivot in the inside radius of wiper arm hook.
  3. Pull on wiper blade pivot into hook until it locks into place.
  4. Check wipers for proper operation.
Wiper Arm To Remove:
NOTE: Mark position of wiper blade on windshield to ensure proper position upon reassembly.
  1. Remove washer hose.
  2. Lift wiper arm from windshield and use a screwdriver to disengage retaining latch.
  3. Remove wiper arm from shaft.
To Install:
  1. Place wiper arm on shaft so that wiper arm aligns with marks placed on windshield.
  2. Press arm assembly on shaft and push retaining latch IN.
  3. Connect washer hose.
  4. Remove windshield markings and check wipers for proper operation.
prev.gif next.gif

Oct 26, 2010 | Chevrolet Suburban 1500 Cars & Trucks

2 Answers

How to change the rubber on wiper blade of 06 corolla


My advice is to forget changing the rubber. Just buy a complete wiper blade minus the arm. This way although you will spend a little more but avoid the hassle and get an entirely new blade. If you buy a quality blade you will only need to replace it once a year or every other year if the car is kept in a garage. I have been using the Rain X Latitude wiper blade and have found it to be a fantastic blade. After 1 year of use it is as good as the day it was installed. Most blades especially rubber blades start to deteriorate after 6 months. Whatever you buy make sure it is made of silicone and not rubber.

Dec 10, 2009 | 2006 Toyota Corolla

2 Answers

Wipers freeze all winter, won't clean the window, have replace the blades 3 times still have the problem


try a different wiper solution one thats a cleaner antifreeze to not just a cleaner

Dec 10, 2009 | 2005 Ford Taurus

1 Answer

How to replace the wiper insert at the back of


moz-screenshot.jpg
  1. REMOVE RR WIPER BLADE
    1. Raise the rear wiper blade to the position as shown in the illustration where the meshing of the claw disengages with a clicking sound. NOTE: Be careful not to break the claw.
    2. Pull straight the rear wiper blade to vehicle's left from the wiper arm. NOTE: Do not fold the rear wiper arm with the rear wiper blade removed from it.1722d05.gif

  1. REMOVE REAR WIPER RUBBER
    1. Place the rear wiper with the rear end of the rubber protruded from the blade stopper as shown in the illustration. NOTE: Do not pull out the wiper rubber forcibly, as the backing plates will become deformed or the blade claws will become damaged. HINT: The rubber can be easily pulled out by pushing the middle area of the blade.
f54b10a.gif
  1. INSTALL REAR WIPER RUBBER
    1. Install the 2 wiper rubber backing plates to the rear wiper rubber. NOTE: Be careful to observe and keep direction of curvature for correct replacement.
0dd144d.gif
b. Insert the rear wiper rubber from the claw of the middle of the rear wiper blade into the rear end position.
8f40009.gif
c. After passing the rear wiper rubber through the rear end side claw, protrude it from the rear end stopper and pass it through the front tip side claw.

Sep 12, 2009 | 2005 Toyota Matrix

1 Answer

Removing wiper blades


6eb8291.gif To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Turn the ignition switch to the ACC.
  3. Set the wiper switch to the PULSE.
  4. Turn the ignition off when the wipers are in the innerwipe position.
  5. Depress the wiper blade clip button
  6. Remove or disconnect the following:
    • The wiper blade from the inside of the wiper arm
gm_mv_ven_wiperbladel.gif
  • The wiper arm out through the opening in the wiper blade
  • To Install:
    1. Install or connect the following:
      • The hook of the wiper arm through the wiper blade opening
      • The wiper blade pivot into the inside radius of the wiper arm hook
      NOTE: Pull the wiper blade until the pivot locks into the hook.
    2. Check wipers for proper operation.

    Mar 30, 2009 | 2003 Pontiac Montana

    1 Answer

    Wiper blades


    hi from uk to remove wiper blades? lift the wiper arm off screen to fully up then turn wiper blade upwards so as to make letter T then if you look at the horseshoe type bend on the arm? where blade fits you will see a little press clip which is part of the wiperblade fitting/securing ? to this blade u section just press clip in with finger and at same time push blade downwards out of the u part of arm then you can refit new blade/s the drivers and passenger wiper blades are different lengths when you fit new blades be sure the clip locks into place ? hope this is clear instructions to understand ?

    Nov 16, 2008 | Hyundai Motor 1998 Accent

    1 Answer

    Front windshield wiper blades


    The 2006 Toyota RAV4 takes a 24" drivers side, 17" passenger side and has a special 17" rear blade. Don't just go by lengths though - when buying windshield wiper blades be sure to always use the application guide book at the store or now-a-days you can Google 'lookup wiper size'.

    You want to look this up because correct wiper fit is more than correct length, it's also proper attachement. Not all attachments fit all arms. Using the application guide or looking up wiper size online will avoid headaches of buying the right lengths with the wrong attachements.

    The replacement wiper blades will come with step-by-step, illustrated instructions and once you have the instructions and the wiper blades/arms in your hands in front of you, it will all make better sense and will an easy maintenance task. Very simple and takes 5-15 minutes usually not requiring any tools. If in your budget, upgrade to the newer-style frameless "beam blades" which perform better than conventional framed wipers. I use Trico NeoForm Beam Blades which are fantastic. Hope this helps!

    PS: Your question is about the front blades but if you address the rear blade too, this vehicle has what they call a "Roc Lock 2" rear arm. You can go to your dealer or I know Trico makes an "Exact Fit Rear Integral Blade 12-A". There may be others available too. I've got the Trico on my Jeep and it fits/works great.

    Aug 11, 2008 | 2006 Toyota RAV4

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    105 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...