Question about 2005 Chevrolet Colorado

1 Answer

Brake lights /hazard work / turn signals work just wont turn on with headlights

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 635 Answers

Possibly bad headlamp switch.

Posted on Nov 03, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 1986 Answers

SOURCE: 1994 chevrolet pickup - brake light problems

There will be an electronic flasher module located under your dash near the steering column (don't know it's exactly location as it varies). It sounds like this unit may be faulty.

Posted on Aug 21, 2009

  • 4 Answers

SOURCE: 99 Chevy Tahoe... Rear turn signals, brake lights, and hazards

I had this problem, and to be honest, it happened to the left side about a week later...it's the board that the bulbs plug into...it's a very common problem with this model. So popular that you can normally get the socket board off the shelf at a parts store! it's extremely simple to replace, and I replaced all the bulbs at the same time!

Posted on Oct 11, 2009

  • 114 Answers

SOURCE: my 97 chevy blazer, the brake lights dont work but

More likely it is the hazard/turnsignal/highbeam/cruise control switch module. It costs about $275 for the module. However there is a repair kit for the likely culprit...the hazard button. Try jiggling it around a little, see if that helps. Spray a little WD-40 into it so it can jostle back into it's correct position. You could try a junkyard unit or Ebay. It's not too hard to change. The hard part is doing it without removing the steering wheel. It can be done. I've done it. But hopefully you can locate the repair kit which costs about 15 dollars. Good luck.

Posted on May 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why aren't hazard lights or brake lights working?


Brake lights /rear hazard lights not working - Ford Truck ...

www.ford-trucks.com > ... > 1967 - 1972 F-100 & Larger F-Series Trucks
Jul 9, 2010 - After checking the brake lights I tried the emergency flashers and found that they are working in the front but not in the back. I do have rear turn ... 1995 F350 Brake Lights / Turn Signals not working
Jul 9, 2012
Turn Signals and Brake Lights Do Not Work
Mar 10, 2012
Turn Signal, Brake Lights, & Rear Hazard not working
Aug 3, 2010
Rear Turn Signals, Hazards and Brake Lights not working....
Aug 29, 200

Sep 30, 2015 | Cars & Trucks

1 Answer

Hazard lights malfunction


YOU MIGHT HAVE A BURNT OUT RELAY IN FUSE COMPART UNDER YOU CARS HOOD CHECK THAT OUT THRU YOUR CARS MANUAL,IT WILL SHOW YOU WHICH RELAY IT IS?

May 24, 2013 | Cars & Trucks

1 Answer

Rear lights not working on 2002 suzuki grand vitara


In the underdash fuse/relay box, the 15A TAIL fuse feeds power to the coil of headlight relay 2. When the combination switch is set to TAIL, the relay closes and the outer tail lamps light. In the same underdash fuse/relay box, the 20A STOP fuse feeds power to the brake light switch. When the brake pedal is pressed, the inner brake lamps light. The underdash fuse/relay box also contains the 10A TURN BACK fuse which feeds power to the hazard switch and the turn signal relay. Relay output is fed to the combination switch and turn signal power is applied to the selected middle tail light. The fourth fuse in the underdash fuse/relay box is the 15A HAZARD fuse which feeds power to the hazard switch and turn signal relay. When the hazard switch is set, the turn lamps on both sides begin flashing.

Sep 18, 2012 | 2002 Suzuki Grand Vitara

1 Answer

Problem with my 97 Chevrolet S10 Blazer


I'd look into the multifunction switch. That controles both hazard and turn.

Dec 12, 2009 | 1997 Chevrolet Blazer

1 Answer

When I turn on the light, only the headlights get turned on. The rear lights do not turn on. Both signal lights are okay. Hazard lights work. Brake lights work.


visually check condition of bulbs,they are 'dual filiment' bulbs,there are 2 fine wires or 'filiments' that light inside bulb.one may have broken,but not the other[the brake & hazard]

Sep 30, 2009 | 2006 Toyota Sienna

1 Answer

No turn signals or brake lights


try turning the hazards on and off several times these switches go bad and will keep the lights from coming on

Dec 31, 2008 | 1998 Mercury Grand Marquis

1 Answer

Headlights and turn signals stopped working


First off, do you have a knob on the dash for the headlights, or do you have a lever on the column that turns them on? If you have the lever on the column, and you can turn on the highbeams by pulling back on the turn signal stalk, and hitting the hazard button turns the flashers on, then chances are the stalk is bad (it's called the combination switch and it's a common failure on the B5 chassis cars (the Passat and Audi A4)).

Try that out - hit the hazard button and see if the hazards work. Pull back on the stalk and see if the high beams come on (they should - toggling like that uses a circuit that is separate from the usual headlight circuits).

Post back up with the results of these checks:

Headlight switch on column or dash?
Highbeams turn on when turn signal stalk is pulled back?
Hazard button activates hazard lights?

Let me know what you find out and I'll be able to tell you more definitely.

Nov 12, 2008 | 1998 Volkswagen Passat

6 Answers

No rear brake light / turn signals on 2001 Chevy Cavalier


The problem is the turn signal/headlight/hazard switch assembly on the steering column which the brake light wiring runs through. The part is easy to change and cost about $50 at most parts stores

Jul 05, 2008 | 2001 Chevrolet Cavalier

Not finding what you are looking for?
2005 Chevrolet Colorado Logo

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...