Question about 2006 Chevrolet Silverado 1500HD

Open Question

What is the torx screw size on a 2007 suburban rotor

Posted by Anonymous on


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1263 Answers

SOURCE: 2007 Chevy Suburban rotor removal

this is a problem that happens alot you have to use an impact driver for this and a impact torx bit. the driver is a cylinder shaped tool with a 3/8 drive head. you get the impact torx the the impact driver and a hammer. the tool is inexpensive and will do the trick.

Posted on May 09, 2009


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What size socket do I use to remove a front rotor?

You don't need a socket. The rotor is held by a torx flathead screw. I stripped mine and drilled it out. It is not necessary. Remove the brakes and this little screw from the rotor and it will come off. If it won't. you need to watch a you tube video about removing a stuck rotor. It is fairly simple. But hard to explain in words.

Jun 22, 2014 | 2006 Buick Lucerne

1 Answer

Replacing brake light

Hi Edward-
The top brake light lens is held on with two size T25 Torx screws. You need a suitable size torx screw driver to remove (and again later replace the assembly) the two screws. Once the screws are removed (do not lose these), you can remove the entire lens assembly. You'll see the wires leading to the plastic bulb socket. The bulb socket twists off the assembly like a bayonet. Once the bulb socket is off, you'll be able to remove the bulb simply by pulling it straight out. Replace the bad bulb by inserting the new bulb and then reassemble your third brake light in the reverse order you removed it. Enjoy!

Apr 01, 2014 | 2007 Dodge Caravan SXT Minivan New Cars

1 Answer

What size is torx screw holding front rotors

T27, guess I will be the only one to actually asnwer the question.

Jan 29, 2013 | 2007 Chevrolet Uplander

1 Answer

Need the size tool to disconnect drivers seat belt assembly from top left side of 1999 Suburban

you will need to use t torx tool it looks like an allen wrench, but in a star pattern. the correct size you need will be either a T-50 or a T-55.

Sep 07, 2011 | 1999 GMC Suburban

1 Answer

Want to know the size of the allen head screw that holds the front caliper together on a 2007 expedition 2wd 5.4 liter limited

These are mostly metric now. Sorry the sizes are not listed in the shop manual. Some are TORX head as well. (star shaped). Take a close look to see what you have. Sears will let you return any unused tools.

Jan 17, 2011 | 2007 Ford Expedition EL XLT

1 Answer


first raise and safely support vehicle remove the wheels remove the spring from the caliper(pry under the spring where it goes into the caliper be careful don't let it fly) locate the two torx bolts holding the caliper to the bracket remove them using the proper size bit remove the caliper by prying it away from the bracket remove the pads by pulling strait out remove the two bolts holding the bracket to the steering knukle(very tight) remove the rotor install is the reverse of removal torque specs are as follows wheels 80-100ftlbs caliper bolts 40ftlbs bracket bolts 90 ftlbs

Sep 24, 2009 | 2007 Dodge Grand Caravan SXT Minivan

1 Answer

I bought new frnt rotors 4 my pontiac sv6 montana and the old ones have a torx screw in them and the new ones donot.did i buy the wrong rotors?

Not necessarily. If the store correctly cross referenced your rotors they are a match. Often after market products will have different styles of hardware. As long as the size and threading is the same you are OK to use the old torx. These bolts can really seize up over time. Spray some liquid wrench or WD-40 and let sit. Best to use an impact driver on theses as a slow wrenching torque can rip the heads off before they break loose. Keep the old hdw.

Jul 05, 2009 | 2005 Pontiac Montana SV6

2 Answers

Tool to remove front brake caliper to replace rotor Escape 2005

You need a 7mm socket, which are available at auto parts stores.

Jun 20, 2009 | 2005 Ford Escape

2 Answers

2007 Chevy Suburban rotor removal

this is a problem that happens alot you have to use an impact driver for this and a impact torx bit. the driver is a cylinder shaped tool with a 3/8 drive head. you get the impact torx the the impact driver and a hammer. the tool is inexpensive and will do the trick.

May 09, 2009 | 2007 Chevrolet Suburban Three-Quarter-Ton...

1 Answer

2006 Silverado - remove front rotors

Yes the torx screw must be removed and you are right the other two threaded holes you can use two bolts screw them in there after you remove the torx and it will push the rotor off the hub and the best way to remove the torx is with a impact driver it is like a screw driver you change the bits but you hit the end with a hammer which the tool then twists and removes the srew you can find them at any tool store prolly even autozone... and if you dont use bolts to push the hub off just use a brass hammer and pound off the rotor

Mar 26, 2009 | 2006 Chevrolet Silverado 1500HD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides