Question about Toyota Corolla

1 Answer

Toyota corolla 1997 engine code p1300 ignitor circuit malfunction #1 car starts after 2 minutes will stop

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 954 Answers

Error Code P1300/ 14. Igniter signal malfunction No.1
Problem Areas:
IGNITION SIGNAL--NO "IGF" SIGNAL TO ECU
--IGNITER/IGNITER CIRCUIT
--IGNITER AND IGNITION COIL/CIRCUIT
--IGNITION AMPLIFIER/ DISTRIBUTOR.
--ECU

Posted on Jan 16, 2014

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

superjorge1
  • 8 Answers

SOURCE: have p0130 and p0133 codes 98 toyota tacoma

check the mass air flow sensor there maybe dirt on the filiment inside the sensor causing false readings. cleaning or replacing it may make the codes go away.

Posted on Nov 18, 2009

duane_wong
  • 6826 Answers

SOURCE: Toyota Corolla 1997 P1300 diagnostic

p1300 is random misfire. It can be caused by a bad O2 sensor, in some cases.

Good luck on this repair.

Posted on Jan 21, 2011

warlock61
  • 659 Answers

SOURCE: more 99 cougar problems

there is a fuse for the o2 heaters if one of the sensors blew the fuse they will all be out

Posted on Mar 01, 2009

GARYca
  • 672 Answers

SOURCE: I have a Toyota vista 1998 model. It's hesitating

replace the ingniter~~

Posted on Mar 24, 2010

Testimonial: "Thank you very much for the help. "

  • 1796 Answers

SOURCE: I have a Mercedes s500

Hi!!
What all this codes have in common is that every single one of them can be caused by a vacuum leak, so carefully check for cracked, loose or disconnected vacuum hoses, wiring to the coils, fuel pressure regulator, fuel injectors, specially on cylinder 2.

  • PO100 - Possible causes are wiring harness failure, air leak or defective hot film MAF sensor
  • PO130 - Vacuum leak
  • PO170 - PO173 - Possible causes are air ingress (leak), fuel injector failure, pressure regulator failure or mechanical wear of engine. Inspect and repair as necessary.
  • PO300 - possible causes are vacuum leak, wiring harness failure or ignition coil defective.
  • PO302 - If limit value for misfire "harmful to TWC" is exceeded, the MIL flashes immediately. If too many combustion misfires occur in one cylinder, the cylinder is switched off (cylinder selective fuel shut off). After the affected cylinders are shut off, the MIL changes from flashing to continuously lit until next time the engine is started. If combustion misfires are recognized, the fault code P0460 or P0462 is set if fuel tank level is too low (fuel reserve indicator light is on). Combustion misfires due to a shortage of fuel are recognized by means of this additional information.

NOTE:After cylinder cut-out system is turned off, the system monitors (through misfire detection) if all intake and exhaust valves are open again.
NOTE:Misfiring may be caused by many faults in the fuel injection system. Usually a misfiring fault is stored with faults pertaining to other components. An engine mechanical fault could also cause a misfire condition.
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Posted on Dec 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P1300 error


The P1300 code is for the ignition coil No.1 and is set when there is no IGF signal to the ECM during engine operation. Possible causes:
Ignition Coil No. 1 harness is open or shorted
- Ignition Coil No. 1 circuit poor electrical connection
- Faulty Ignition Coil No. 1
- Faulty Engine Control Module (ECM) God-Bless!

Oct 03, 2015 | 2003 Toyota Corolla

2 Answers

P1300,p 1305,p1310,p1315 how do i fix these fault codes on a Occasionally stall & engine check light on.


You have an at times fault which is loss of spark on all four cylinders. Worse case is the engine control module (quite expensive) so lets keep that for last cause. If it were to fail it would more than likely 100% of the time. Therefore the most likely causes are either a dirty connector or loose ground. See image 1&2 below to uncover coil on plugs. locate connector plugs common to all four plug wires. There are two junction connectors A & B. With key off remove connectors, check for bent pins and spray with DOXIT a radio shack product that is a great No Touch pin cleaner. Replace connectors. One wire from each of the four coil on plug wires leads back to the ECM (Electronic Control Module) Connector A (it is labeled). disconnect and perform same procedure using spray. Reconnect...you'll need to clear codes by disconnecting positive battery terminal for 3 minutes. Test run vehicle to see if troubles have cleared...If not; do you have a multimeter and a wee bit of experience using one? If so put on lowest ohm setting...Hold one terminal on the negative battery terminal...right on the post...Hold the other on bare metal of chassis as in fender...record reading...While holding lead on battery terminal move the other lead to metal of engine block...record readings...Must be close to zero ohms about 1 to 200...If readings are around 2000 ohms the car has an inadequate ground...If so send me a message...saailer@ec.rr.com














25689133-it05lymtu1334i4my0oofgx5-1-1.gif

25689133-it05lymtu1334i4my0oofgx5-1-3.gif

p1300-p-1305-p1310-p1315-fix-fault-codes-fsiw50wukvgddzmkmreyzoen-5-3.gif

May 10, 2015 | 2003 Toyota Corolla

1 Answer

Toyota p1300


Error Code: DTC P1300
Description: Igniter Circuit Malfunction
Solution:
To repair the code please do the following:
1. Check spark plugs.
2. Check for open and short in harness and connector in IGF (Ignition Confirmation) signal circuit between ECM and igniter.
3. Disconnect igniter connector and check voltage between terminal IGF of ECM connector and body ground.
4. Check for open and short in harness and connector in IGT1 - 3 signal circuit between ECM and igniter.
5. Check voltage between terminals IGT1 - 3 of ECM connector and body ground.
6. Disconnect igniter connector and check voltage between terminals IGT1 - 3 of ECM connector and body ground.
8. Check for open and short in harness and connector between ignition switch and ignition coil, ignition coil and igniter.
9. Check and replace ignition coils with a good known one.
10. Check and replace ECM with good a known one .
Hope that works.
Thank you for visiting Fixya.

Apr 06, 2014 | 2001 Toyota Corolla

1 Answer

Code p1315


DTC P1315 is Igniter Circuit Malfunction (No.2).
Check No. 2 ignition coil.
See the link below for more information from a 2000 to 2002
Toyota Echo Service Manual.
Diagnostics: Engine: P1300, P1305, P1310, P1315 Igniter Circuit Malfunction (Echo)

Hope that helps.

Sep 19, 2013 | 2001 Toyota Echo

2 Answers

P1300,p 1305,p1310,p1315 how do i fix these fault codes on a Toyota echo 2005.


P1300 Igniter Circuit Malfunction / 14
P1305 Igniter No. 2 Circuit Malfunction / 15
P1310 Igniter No. 3 Circuit Malfunction /15
P1315 Igniter No. 4 Circuit Malfunction

444a5478-5b0c-4e6e-8a98-e031ba8bc972.png

Jan 07, 2013 | 2005 Toyota ECHO

1 Answer

Toyota Corolla 1997 P1300 diagnostic code, how can I fix this problem? This car has the "Check Engine" light on. Please help!


p1300 is random misfire. It can be caused by a bad O2 sensor, in some cases.

Good luck on this repair.

Jan 21, 2011 | Toyota Corolla Cars & Trucks

2 Answers

I have error codes of p1300,p1305, p1310, p1315, on my toyota an am looking for the deffinations and issues thse codes create. I have a 2002 tacoma.


P1300 = ignition system malfunction (#1 coil/igniter circuit fault)
P1305 = same as above but #2 coil
P1310 = #3 coil
P1315 = #4 coil

Oct 31, 2010 | 2002 Toyota Tacoma

1 Answer

1997 corolla codes p0130 / 0133


P0130 IS Oxygen Sensor Circuit Malfunction
(Bank 1 Sensor 1)
P0133 IS
Oxygen Sensor Circuit Slow Response
(Bank 1 Sensor 1)

Apr 16, 2010 | 1997 Toyota Corolla

1 Answer

I have problem with code 1126 (toyota 4 runner 2001


Manufacturer Specific Codes

P1100
BARO Sensor Circuit - Read Our Article on Automotive Circuit Testing For Help With This Toyota Check Engine Light Code

P1120 Accelerator Pedal Position Sensor Circuit - Read Our Article on Automotive Circuit Testing For Help With This Toyota Check Engine Light Code

P1121 Accelerator Pedal Position Sensor Range/Performance Problem

P1125 Throttle Control Motor Circuit - Read Our Article on Automotive Circuit Testing For Help With This Toyota Check Engine Light Code

P1126 Magnetic Clutch Circuit

P1127 ETCS Actuator Power Source Circuit

P1128 Throttle Control Motor Lock

P1129 Electric Throttle Control System

P1130 Air/Fuel Sensor Circuit Range/Performance (Bank 1 Sensor 1) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code - More Related Information

P1133 Air/Fuel Sensor Circuit Response (Bank 1 Sensor 1) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code

P1135 Air/Fuel Sensor Heater Circuit Response (Bank 1 Sensor 1) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code - More Related Information

P1150 Air/Fuel Sensor Circuit Range/Performance (Bank 1 Sensor 2)

P1153 Air/Fuel Sensor Circuit Response (Bank 1 Sensor 2) - Read Our Article On Oxygen Sensor Codes For Help With This Toyota Check Engine Light Code

P1155 Air/Fuel Sensor Heater Circuit. (Bank 1 Sensor 2)

P1200 Fuel Pump Relay Circuit

P1300 Igniter Circuit Malfunction - No. 1

P1305 Igniter Circuit Malfunction - No. 2

P1335 No Crankshaft Position Sensor Signal - Engine Running

P1349 VVT System

P1400 Sub-Throttle Position Sensor

P1401 Sub-Throttle Position Sensor Range/Performance Problem

P1405 Turbo Pressure Sensor Circuit

P1406 Turbo Pressure Sensor Range/Performance Problem

P1410 EGR Valve Position Sensor Circuit Malfunction - Read Our Article on EGR Valve Codes For Help With This Toyota Check Engine Light Code

P1411 EGR Valve Position Sensor Circuit Range/Performance - Read Our Article on EGR Valve Codes For Help With This Toyota Check Engine Light Code

P1500 Starter Signal Circuit

P1510 Boost Pressure Control Circuit

P1511 Boost Pressure Low

P1512 Boost Pressure High

P1520 Stop Lamp Switch Signal Malfunction

P1565 Cruise Control Main Switch Circuit

P1600 ECM BATT Malfunction

P1605 Knock Control CPU

P1630 Traction Control System

P1633 ECM

P1652 Idle Air Control Valve Control Circuit

P1656 OCV Circuit

P1658 Wastegate Valve Control Circuit

P1661 EGR Circuit

P1662 EGR Bypass Valve Control Circuit

P1700 Vehicle Speed Sensor '2' Circuit Fault

P1705 Direct Clutch Speed Circuit Fault

P1765 Linear Shift Solenoid Circuit Fault

P1780 Park/Neutral Position Switch Malfunction (Only For A/T)

Back To Top Of Toyota Check Engine Light Codes Page

Mar 21, 2009 | 2002 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

630 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...