Question about Chevrolet Cavalier
Yes, the filler tube can be change...ask for used parts or new at the dealer
Posted on Oct 19, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
You have to remove the spark plugs cables and remove the four nuts that you see when the cables are removed.
When the four nuts are removed, simply raise the valuve cover. When replacing the gasket, make sure you get the gromets as well. Those sometimes get worn or crack since they are more exposed than the value cover gasket. Make sure that you clean the cover from oil and replace the gasket with no use of silicon.
Posted on Aug 04, 2008
No start on 97 dodge intrepid. I Know that Coil pack is Below Valve cover and Have repaired Numerous Ignition coils due to there becoming Oil soaked , the oil will gather dust dirt and thus Insulating ( Retaining Heat) i and this Causes them to Over heat and Fail , in short Burning them out. I say this Because of your Mention of it as a symptom. you must first Determine if it is getting spark ,have someone Crank Engine over While you are Holding the Spark plug wire 1/4 inch away from coil tower (TERMINAL) do this to all 6 if no spark at any of them ,that coil could be bad (Most Likley), If all Have NO SPARK then it is One of the fallowing,,
NOW if you have Spark on All 6 Cylinders Check for fuel delivery, Do this at the shrader Valve on the fuel rail,(LOOKS LIKE AIR FILL VALVE ON WHEELS) Simply remove cap turn key on for 5 seconds then turn it OFF Depress the Stem at shrader valve If you get a Good SPRAY of FUEL upon doing this 3-4 times then you have Fuel Pressure !!!!WARNING !!! Test Equipment is Recommended for all Procedures but their certain steps to take if you don't have a DIGITAL VOLT METER or Fuel Pressure tester. I Hope this helps you with your Diagnosis od the problem. Have A Good Day
Posted on Jan 13, 2009
ALL DATA time to R&R valve cover gaskets both sides is 2.1 hours. you will need to remove brackets and connectors on either side, It will also help to take the upper plenium bolts out but not completly pull the plenium. If you don't have a lot of mechanical experiance and some basic tools. you may want to consider to have a local a shop to perform this service for you after you get a estimate. RON.
Posted on Jan 18, 2009
Hello. Let me try to assist you the best I can, with the hope of achieving a FixYa rating from you for my assistance.
Changing the rear valve cover gasket on your vehicle would be not considered a "real" big job, but IS a time-consuming job.
In order to remove the rear cover, you first have to remove the intake plenum. If you do not remove the plenum, you can't get to the valve cover bolts that are under the plenum. After the plenum is off, the valve cover is easy to access. You will also need to replace the intake plenum gasket, if you do the job yourself.
I hope this information has satisfied your question.
Thanks for choosing FixYa for assistance!
Posted on Jan 28, 2009
you will have to put another valve cover gasket on between each cylinder there is a round gasket between valve cover and cylinder head if you buy the valve cover gasket kit they will be in the kit .please rate this answer thanks.
Posted on Feb 01, 2009
Tips for a great answer:
Jun 15, 2016 | Cars & Trucks
Nov 09, 2014 | 2000 Chevrolet Cavalier
Aug 11, 2014 | 2001 Chevrolet Cavalier
Apr 13, 2014 | 1994 Geo Metro
Sep 22, 2011 | 2004 Chevrolet Cavalier
Sep 09, 2010 | 1996 Saturn SL
Oct 18, 2009 | 1997 Chrysler LHS
Aug 11, 2009 | 1999 Volkswagen Jetta
Dec 29, 2008 | 1995 Toyota Land Cruiser
37 people viewed this question
Usually answered in minutes!