Question about 1997 Dodge Caravan

Open Question

3.3L v6 Crankshaft Position Sensor replacement

Posted by on

  • Jennifer
    Jennifer Oct 18, 2013

    Or the Camshaft

×

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
csmock132
  • 4669 Answers

SOURCE: Where is the crankshaft position

It is stuck in bellhousing of the transmission near the rear head. The new crank sensor will come with a piece of gasket paper on the end of the sensor. Install the sensor all the way in against the pick-up wheel. When you crank the engine the wheel will rip off the paper and the adjustment will be correct.

Posted on Mar 10, 2009

Ad
  • 9 Answers

SOURCE: 1997 dodge dakota v6 engine wont start replaced

turn the key to the on position a see if you can here a buzzing sound around the fuel tank,if you don't hear a sound then. (be very careful while doing this) with the key off take a fuel line coming from the tank loose,make sure its pointed away from you and turn the key to the on position,see if any gas comes out,if not then your fuel pump is probably bad.

Posted on Mar 05, 2009

  • 151 Answers

SOURCE: crankshaft sensor

2-0L-2.4L I-4 crankshaft sensor mounts to the engine block, behind the alternator, just above the oil filter. 2.5L V-6 crankshaft sensor mounts to transaxle just below the distributor.

Posted on May 07, 2009

csmock132
  • 4669 Answers

SOURCE: crankshaft position sensor

It should be in the side of the block above the lip of the oil pan. Go through the wheel well. Passenger side.

Posted on Jun 05, 2010

  • 56 Answers

SOURCE: cant find crankshaft position sensor on my dodge

right back of the engine near bellhousing under exhouse manifold

Posted on Jun 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the crank sensor located on a 06 toyota highlander


images for Where is the crank sensor located on a 06 .

How To Install Replace Crankshaft Position Sensor Toyota ...

? 6:58
https://www.youtube.com/watch?v=M6zU6jh8pNc
Jan 24, 2011 - Uploaded by 1A Auto Parts
How To Install Replace Crankshaft Position Sensor ToyotaCamry 3.0L V6 1AAuto.com ... the crankshaft position sensoron a 1994 Toyota Camry 3.0L V6. ..... 2002-2006 LEXUS ES300 ES330 TOYOTA CAMRY KNOCK ...

Dec 05, 2015 | Toyota Cars & Trucks

1 Answer

Replace crankshaft position sensor in 2003 dodge caravan 3.3 V6


According to Haynes, the V6 engine has the sensor mounted in the bellhousing on the back of the engine.

Aug 20, 2012 | Cars & Trucks

1 Answer

Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

Nov 14, 2011 | 2000 Nissan Xterra

1 Answer

3.1 v6 location of crankshaft position sensor at rear of engine. have the exhaust crossover off and other parts as well.


CRANKSHAFT POSITION SENSOR IS BEHIND CRANKSHAFT PULLEY.YOU HAVE TO REMOVE CRANKSHAFT PULLEY TO REPLACE THE CKP SENSOR.

Jun 19, 2011 | 2002 Chevrolet Malibu

1 Answer

Where is the crankshaft sensor on a v6 2000 chrystler sebring


CRANKSHAFT POSITION SENSOR - 2.5L
REMOVAL
Remove speed control servo from driver's side strut tower.
Remove crankshaft position sensor retaining bolt Crankshaft Position Sensor
Pull crankshaft position sensor straight up out of the transaxle housing.
(Disconnect crankshaft position sensor electrical connector from the wiring harness connector.
INSTALLATION - ADJUSTABLE
All vehicles will be equipped with an adjustable crankshaft position sensor. This can be identified by an elongated mounting hole in the sensor.

NOTE: If the removed sensor is to be reinstalled, clean off the old spacer on the sensor face. A NEW SPACER must be attached to the sensor face before installation. If the sensor is being replaced, confirm that the paper spacer is attached to the face of the new sensor Crankshaft Position Sensor and Spacer

Install sensor in transaxle and push sensor down until contact is made with the drive plate. While holding the sensor in this position, install and tighten the retaining bolt to 12 N·m (105 in. lbs.) torque.
Connect crankshaft position sensor electrical connector to the wiring harness connector.
Attach connector to heater tube bracket.
Install speed control servo. Tighten nuts to 9 N·m (80 in. lbs.) torque.

May 22, 2010 | 1998 Chrysler Sebring

Not finding what you are looking for?
1997 Dodge Caravan Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...