Question about 1992 Oldsmobile Cutlass Ciera

1 Answer

Codes trouble olds engine troublecodes

Dtc 26 & dtc27

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Oldsmobile Master
  • 1,250 Answers

Quad driver A fault
ECM module have input and ouput, quad driver are there to activate a solenoid or relay
quad driver A drive a few of those output
example quad driver A control canister purge solenoid and the solenoid is defect . the quad driver will kick off until you change the solenoid
there is two kind of driver 1984 to .......one will reset if trouble is repair
the other one is the ecm module itself have to be change after is repair .....(quad driver act has a driver or big fuse)

Posted on Oct 19, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the number 12 trouble code on my 95 camry dx 2200 engine


1995 Camry 2.2L OBD1 Code 12
Trouble Code 12

Trouble Code 12 Definition:
Engine speed (RPM) sensor -circuit

Trouble Code 12 Meaning:
Wiring, RPM sensor, ECM

Diagnoses Time:
Voltage reading between Engine Control Module(ECM) and RPM sensor.

http://www.troublecodes.net/toyota/toyota-camry-cressida/

Mar 08, 2017 | 1995 Toyota Camry

1 Answer

Where is the obd2 connector location on holden ra rodeo v6


isuzimpuls.gif
Connect white (test lead) and black (ground lead) wires that are branched from harness approximately eight inches from ECM. After leads are grounded, the "Check Engine" light will flash the diagnostic trouble codes. The DTC's are indicated by the flashing CEL.
FLASH, FLASH, pause, FLASH, FLASH, FLASH = Code 23.
If only one diagnostic trouble code is stored, the DTC will repeat continuously until test leads are disconnected. If more than one diagnostic trouble code is stored, each DTC will repeat three times, starting with the lowest, then proceed to the next DTC. After all DTC's have been displayed, the pattern will repeat.I-MARK 84-85
Connect male and female test leads taped into wire harness near ECM. After leads are connected, the "Check Engine" lamp will flash the trouble codes. The DTC's are indicated by the flashing CEL.
FLASH, FLASH, pause, FLASH, FLASH, FLASH = Code 23.
If only one diagnostic trouble code is stored, the DTC will repeat continuously until test leads are disconnected. If more than one diagnostic trouble code is stored, each DTC will repeat three times, starting with the lowest, then proceed to the next DTC. After all DTC's have been displayed, the pattern will repeat.
86-87 Impulse located near the ECM connector, is used to actuate the Engine Control Module (ECM) trouble code memory within the module. Two terminals (A and C) of this connector are used to activate the diagnostic trouble code system in the ECM. With the ignition switch turned On, engine Off, connect a jumper wire between terminals A and C. The "Check Engine" lamp will begin by flashing a DTC 12. DTC 12 = flash, pause, flash, flash. There will be a longer pause and a code 12 will repeat two more times. This code indicates the self-diagnostic system is operating. The cycle will then repeat until the engine is started or the ignition is switched Off. In most cases, DTC's will be checked with the engine running since no DTC's other than DTC 12 or 51 will be present without the engine running. Remove jumper wire from ALDL connector before starting engine. Reconnect jumper wire after engine is running.

Throttle Body Fuel Injection

The ECM test connection is located under the center console.
A built-in, self diagnostic system will identify problems in the throttle body fuel injection system. When a problem is detected, the diagnostic system will illuminate the "Check Engine" light.
When the engine is started, the Check Engine light should turn off.. If the light remains lit, the self diagnostic has detected a problem. To determine where the problem exists, ground the "Test" terminal of the connector with the ignition On, engine Off and watch the check engine light. Each DTC will flash three times (lowest to highest).

Aug 21, 2014 | Holden Rodeo Cars & Trucks

1 Answer

Trouble code 27


you did this on a 94 integra
http://www.troublecodes.net/acura/

and got one of these. 27 is not on list. count it wrong?
http://www.troublecodes.net/acura/86-94acurabasic/

Dec 30, 2013 | 1994 Acura Integra

1 Answer

Readiness codes for a cr-v 2009


yes, readiness. this is honda jargon.
it just means to make sure after scanning ECU. that
there are no DTC's

key on, is cel glowing, good,
run engine, drive 20 miles. does the CEL lamp stay off
no, that is bad, it means DTCs are stored.
scan it and pull the codes.
all cars 1996 to present, honda or not , in the USA (only)

old codes
http://www.troublecodes.net/honda/

new codes are here DTCs.
buy the FSM on car, or see it at alldata dot com.
all data and fsm shows how to find the actual reasons for and DTC.

just the codes are here
http://engine-codes.com/make/honda

Sep 24, 2013 | Honda CR-V Cars & Trucks

1 Answer

I read the check engin light on my 1993 toyota camry le and it gave me to codes: DTC:14 and DTC:26... What could be wrong with my car?


Code 14: Igniter circuit, probably a faulty igniter
Code 26: Fuel mixture too rich, possibly a faulty coolant temperature sensor, or faulty oxygen sensor

Jan 15, 2012 | 1993 Toyota Camry V6

1 Answer

Transmittion seems to stick in 2nd/3rd gear. Won't go into OD until you punch it...sometimes feels like it slips into nuetral...1995 Sonoma Vortec V6


Before guessing at transmission problems, check the fluid level (car warmed up, engine running in Park on level ground) and have the PCM scanned for trouble codes FIRST.
1-2 / 2-3 shift is delayed and harsh, may not shift into OD: Check TPS for smooth and linear electrical response over the entire range of motion. If not, replace.
Start with that and here is a link for obtaining your DTC codes to your Sonoma. http://www.troublecodes.net/GM/
Thank you for using fixy and good luck

May 10, 2010 | 1995 GMC Sonoma

2 Answers

P1443 computer code what is it on my 1996 ford thunderbird


P1443 = A problem with the EVAP purge flow system
Continuous Memory Diagnostic Trouble Code (DTC) P1443 indicates an incorrect Evaporative System Purge Control Valve flow.

Possible causes:
-- Obstructed, open or cracked hoses between EVAP canister purge valve and intake manifold.
-- Damaged EVAP canister purge valve.
-- Damaged PF sensor.

Hope help with this.

Apr 25, 2010 | 1996 Ford Thunderbird LX

1 Answer

1991 Cavalier with 2.2 won't start. Cranks strong. Can hear fuel pump energize. Connected noid light to efi circuit - no light. What should I look for next?


Start with check for any DTC codes that may help you address your engine's starting issue. Here is a link for you to retrieve your DTC codes. You could have a bad ICM (ignition control module) or crankshaft sensor that need to be replaced. Check all your fuses just to make sure nothing is left out.
http://www.troublecodes.net/GM/
Thank you for using Fixya and good luck

Apr 04, 2010 | 1993 Chevrolet Cavalier

2 Answers

89 acura legend check engine light is always on


IF YOU LOOK UNDER DRIVERS SEAT FROM BACK PASSENGER SEAT YOU'LL SEE THE CARS ECU IS MOUNTED THERE. THERE WILL BE A SMALL LITTLE "WINDOW"ON BACK EDGE THAT WHEN YOU TURN THE KEY INTO THE ON POSITION ANY TROUBLE CODES WILL CAUSE A RED LIGHT TO BLINK IS THIS WINDOW. THE SERIES OF FLASHES(LONG FLASH=10 SHORT=1) WHICH TRANSLATE INTO DTC . EXAMPLE TWO LONGS FOLLOWED BY 3 SHORTS ==DTC 23. IF THERE ARE MORE THAN ONE DTC STORED THERE WILL BE LONG PAUSE BETWEEN EACH SERIES OF FLASHES

Jun 18, 2009 | 1994 Acura Legend

1 Answer

Engine trouble code (web site) list 2004 intrepid 2.7 lit


Visit http://www.troublecodes.net

The site will help you as regards a number of cars/ trucks.

Cheers.

Rate this fixya.

May 21, 2009 | 2004 Dodge Intrepid

Not finding what you are looking for?
1992 Oldsmobile Cutlass Ciera Logo

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...