Question about Hyundai Santa Fe

1 Answer

Key out still running

When i remove the key, my truck is still running for a while. i do not know if is the ingnition switch or some electric problem.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

  • Expert
  • 162 Answers

After you pull out the key step on the brake, if the car shuts off you have a remote starter installed on this vehicle.

Posted on Oct 19, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: 1995 chevy impala ingnition

I had the same problem last summer. Poor thing was dead for 2 months. Finally figured it out. Under the steering column (under the driver's side dashboard) there's a small connector with an orange cable that has two small white wires inside it. These wires come from the ignition switch, and run to the PCM (computer). The small chip in your key isn't being detected. The two wires on this connector connect to the key when it's in the slot. The ignition switch is bad, and not connecting to the key when it's inserted. Try cleaning up the chip contacts on your key, or try your spare key if you have one. Also spray a small amount of contact cleaner into the ignition switch. Insert, and re-insert the key a bunch of times to clean up the inner contacts. This should take care of it. Post a follow-up message to let me know if it worked or not. There's another solution, but it's not something I'd wanna post online because it gives away how to bypass the Pass Key theft deterrent system.
GOOD LUCK!

Posted on May 13, 2009

  • 5 Answers

SOURCE: ingnition switch broken in pieces

The best solution at this point is to replace the entire assembly.

Posted on May 27, 2009

  • 79 Answers

SOURCE: Truck won't start. Dash lights come on when key

try tapping stater with hammer then try to start it if it cranks starter is bad

Posted on Jul 31, 2010

  • 335 Answers

SOURCE: how do you remove the

First disconnect the battery then put the key in the ignition then use a paperclip to put in the little hole thats right below the key, while holding the paperclip in the hole turn the key counter clockwise and pull the ignition switch out.

Posted on Mar 19, 2011

  • 256 Answers

SOURCE: when i turn off the key of my 1.9d 2000 vw passat the engine keeps running and will not switch off till i remove one of the electric window fuses.also when the key is removed the electric windows stil

Take it in to a auto electric shop to be check out,

Posted on Dec 06, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove ignition key lock cylinder. when my key will not turn ingnition?


remove the plastic bowl around steering column to gain access around switch and u should see like tab u can press on the switch with a screw driver

Feb 26, 2015 | 1997 Oldsmobile Bravada

1 Answer

Vw ingnition light stays with key off


one of the 2000 VW electrical gremlins. most likely cause is a bad ignition switch.

Sep 23, 2012 | 2000 Volkswagen GTI

1 Answer

Need shifter my key is stuck in my ingnition


Call a locksmith and try to get that key removed, it effects all of the electrical in your car and locks down the shifter as you probably already know about. May have to replace the ignition switch.

Oct 06, 2010 | 1999 Mazda Millenia

1 Answer

Car wont turn over and start, but lights and everything else works It will not do anything when you turn over the key.


The key switch connects to the ingnition switch which electrically actuates the circuitry to engage the starter motor, the link or this switch could be the fault if all cables/wiring and relays/fuses are good.

Aug 10, 2010 | 1995 Pontiac Grand Am

2 Answers

Ignition


the actuator inside the sterring column that the lock cylinder turns is boken, this is a very complex job and is not for the home tech without a factory service manual.

Apr 21, 2010 | 1996 Ford Taurus

1 Answer

How to replace an ignition switch on a 1990 honda accord lx


take off the plastic caseing arround it and it hase two screws holding it down question is ithe the key cylinder or the ingnition or electrical harness they are 2 seperate parts( electrical harness ) has 2 small screws philips can be removed with out key cylinder or all together 2 screws holding the key cylinder in place

Apr 08, 2010 | 1990 Honda Accord

2 Answers

If you turn the key to acc, nothing happens, if you turn it to on, nothing happens, but if you turn it all the way to start, it does star but when the key springs back like normal, it turns the truck off....


did you replace the switch or did you replace the ingnition cylinder (cylinder is the part the key goes in)the switch is what controls the start acc and keeps the car or truck running

Jan 02, 2010 | 1990 Ford F150

1 Answer

1995 chevy impala ingnition


I had the same problem last summer. Poor thing was dead for 2 months. Finally figured it out. Under the steering column (under the driver's side dashboard) there's a small connector with an orange cable that has two small white wires inside it. These wires come from the ignition switch, and run to the PCM (computer). The small chip in your key isn't being detected. The two wires on this connector connect to the key when it's in the slot. The ignition switch is bad, and not connecting to the key when it's inserted. Try cleaning up the chip contacts on your key, or try your spare key if you have one. Also spray a small amount of contact cleaner into the ignition switch. Insert, and re-insert the key a bunch of times to clean up the inner contacts. This should take care of it. Post a follow-up message to let me know if it worked or not. There's another solution, but it's not something I'd wanna post online because it gives away how to bypass the Pass Key theft deterrent system.
GOOD LUCK!

Mar 28, 2009 | 1995 Chevrolet Impala

1 Answer

I need instructions on how to put a locksmart switch ingnition


Removal
  1. Disconnect battery ground cable. Remove the steering column shroud by removing the four or five self-tapping screws. Remove tilt lever (if so equipped).
  1. Remove instrument panel lower steering column cover.
  1. Disconnect the ignition switch electrical connector.
  1. Rotate ignition key lock cylinder to the RUN position.
  1. Remove the two screws retaining ignition switch.
  1. Disengage the ignition switch from the actuator.
Installation
  1. Adjust the ignition switch by sliding the carrier to the switch RUN position. NOTE: A new replacement switch assembly will be set in the RUN position as received.
  1. Check to ensure that the ignition key lock cylinder is in the RUN position. The RUN position is achieved by rotating the key lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch into the actuator. It may be necessary to move the switch slightly back and forth to align the switch mounting holes with the column lock housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is locked in the LOCK position.
  1. Install instrument panel lower steering column cover.
  1. Install the steering column trim shrouds and tilt lever (if so equipped).

Feb 26, 2009 | 1991 Lincoln Town Car

1 Answer

97 cavalier was running but just stopped.


Question:
Did you replace the ignition switch or the KEY AND CYLINDER?

These are the only 2 things that can make your engine turn off when you release the ignition switch after starting the engine.

I hope this helps you.
ramonalees.com

Jan 30, 2009 | 1997 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8567 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...