Question about Cars & Trucks

1 Answer

My 1997 acura just had a new water pump and timing belt install now i run the motor and the crankshaft sensor code comes on but the motor runs

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 109 Answers

Do it again, it is set on the wrong tooth. 1 off

Posted on Jan 02, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
canbruce75
  • 1776 Answers

SOURCE: How to install a water pump for a 1997 acura tl

I suggest that you visit the autozone.com website and register the car information. It doesn't cost anything and will give you access to an online repair manual for the car. The steps for replacing the water pump should be available there. It's a handy resource for anyone doing their own automotive maintenance and I'm sure you will find it useful. Sure hope so and I hope this helped. Best wishes.

Posted on Sep 16, 2009

  • 1757 Answers

SOURCE: replacing timing belt, water pump, on 2004 acura tl

My sincere apologies for the delayed response.
I have only been a free contributor to this site for the last 4-months.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, however I am answering it either way.

Click on the following direct Link. It has several Diagrams you will need for your Timing Belt replacement. Included are the Cover Bolt Locations, Tool Needed and Marks for your specific engine.
You may also want to Print out these Diagrams for future use.

Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Again my apologies...


http://www.2carpros.com/car_repair_information/year/2004/make/acura/model/tl/2004_acura_tl_timing_belt_diagram_marks.htm

Posted on Mar 17, 2010

franktilt
  • 403 Answers

SOURCE: My 2.5 V6 in 1997 Sebring Jxi runs rough after I

the timing is off you need to readjust it. most likely the motor is running rough because of inaccurate combustion.

Posted on Feb 07, 2011

  • 3074 Answers

SOURCE: CODE P0016 CAM /CRANK CORRELATION

there you go the timing is off:

http://www.obd-codes.com/p0016

alignment for timing:

http://www.2carpros.com/diagrams/toyota/avalon/2003

Posted on Apr 19, 2011

timothymerch
  • 175 Answers

SOURCE: i changed the timing belt and water pump on a 1997

reclear code

Posted on Oct 18, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where is crank position sensor on a 1994 toyota 2.2liter 4cyl ?


Where is the crank position sensor on a 95 Toyota celica gt 2.2

search.aibing.cc/Where+is+the+crank+position+sensor+on+a+95+Toyota...
P1335, No Crankshaft Position Sensor Signal - Engine Running. ... 91 1991 ToyotaCelica GTS Engine Mount Right 2.2L 4 Cyl Genuine. ... 1990, 1991, 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001 . ... Powered by a 2.2-liter engine, the Celica now had ST and GT trim models. ... in 1986 and a 2.0-liter ...

Where is crank position sensor on a 1994 toyota 2.2liter 4cyl ...

www.fixya.com/cars/t26080657-crank_position_sensor_1994_toyota
31 mins ago - It is not behind pully nor in dist all videos show - Toyota Cars & Trucks question. ... Change a crankshaft position sensor on a 2000 eclipse.

toyota camry crankshaft sensor - ABMforum.com

abmforum.com/toyota-camry-crankshaft-sensor.html
toyota camry crankshaft sensor 99 camry crankshaftcamshaft position codes i got a problem with my 97 ... The car 96 toyota camry 2.2 liter 4 cyl. ... 1994 toyota camry 2.2L 257k miles Symptoms Car overheats Top radiator hose hot bottom cold ...

Toyota Camry 5SFE Engine Timing Belt, Water Pump and ...

hubpages.com > Autos > Do It Yourself Auto Repair
Jul 10, 2014 - The Toyota 5SFE motor is a four-cylinder, 2.2 liter, timing-belt-driven, double ..... Remove the lower timing belt cover with the crankshaft position sensor. ..... I've never, ever replaced the harmonic balancer on a 4cyl 5SFE.

1995 Toyota Camry LE 4 cylinder - YouTube

? 2:27
https://www.youtube.com/watch?v=7TW6hlUiHWQ
Sep 6, 2011 - Uploaded by jacasan2000

Feb 03, 2016 | Toyota Cars & Trucks

1 Answer

1997 Acura CL 2.2, car cranks but will not start,does not have spark. When trying to start the D4 light will blink. Have changed fuel pump, distribitor, injector relay, computer, ignition relay under dash...


have u checked ur timing chain/belt? or even the crankshaft sensor? The crank sensor (if bad or broke) will cut out the spark to ur plugs. hope this helps

Sep 29, 2013 | 1997 Acura CL

1 Answer

Water pump 2000 3.0 liter dodge caravan


For The 3.0 Motor. (3.3 Way down the line.)

Drain cooling system.
Remove timing belt. Refer to Engine for procedure.
Remove water pump mounting bolts.
Separate pump from water inlet pipe and remove water pump.

Timing Belt Removal
Raise vehicle and remove accessory drive belt splash shield (Fig. 66).
Remove accessory drive belts.
Remove crankshaft pulley and damper (Fig. 68).
Support engine and remove right side engine mount.
Remove engine support bracket (Fig. 67).
Remove timing belt covers (Fig. 67).
Mark belt running direction for installation (Fig. 69).
Loosen timing belt tensioner bolt (Fig. 71) and remove timing belt.
Remove crankshaft sprocket flange shield (Fig. 68). CAMSHAFT SPROCKETS To remove camshaft sprockets
Hold camshaft sprocket with Spanner Tool MB-990775. Loosen and remove bolt and washer (Fig. 70).
Remove camshaft sprocket from camshaft. To install camshaft sprockets:
Place camshaft sprocket on camshaft.
Install bolt and washer to camshaft. Using Spanner Tool MB-990775, hold camshaft sprocket and torque bolt to 95 Nm (70 ft. lbs.) (Fig. 70). TIMING BELT TENSIONER
Install timing belt tensioner and tensioner spring.
Hook spring upper end to water pump pin and lower end to tensioner bracket with hook out (Fig. 71).
Turn timing belt tensioner counterclockwise full travel in adjustment slot and tighten bolt to temporarily hold this position (Fig. 72).

INSTALLATION


Install timing belt on crankshaft sprocket and keep belt tight on tension side (Fig. 69). Install belt on the front (radiator side) camshaft sprocket. Install belt on the water pump pulley, rear camshaft sprocket and finally on the timing belt tensioner.
Rotate the front camshaft sprocket in opposite direction to take up belt slack. Check that all timing marks are aligned (Fig. 69).
Install crankshaft sprocket flange (Fig. 68).
Loosen tensioner bolt and allow spring to tension timing belt.
Turn crankshaft two full turns in clockwise direction. Turn smoothly and in clockwise direction ONLY.
Align the timing marks on the sprockets and tighten the timing belt tensioner locking bolt to 28 Nm (250 in. lbs.) torque.
Install timing belt covers.
Install engine support bracket.
Install right side engine mount.
Install crankshaft damper and pulleys (Fig. 68). Tighten damper center bolt to 135 Nm (100 ft. lbs.) .
Install accessory drive belts.
Install accessory drive belt splash shield (Fig. 66).

Be sure to also replace all the cam and crank seals why you are there. Might as well put a belt on too.

FOR THE 3.3 OR 3.8 MOTORS.

Drain Cooling System.
Remove accessory drive belt.
Remove right front lower fender shield.
Remove water pump pulley bolts and remove pulley.
Remove water pump mounting screws. Remove water pump.
Remove and discard O-ring seal.
Clean O-ring groove and O-ring surfaces on pump and chain case cover. Take care not to scratch or gouge sealing surface

Installation

Install new O-ring into groove.
Install water pump to chain case cover. Tighten screws to 12 Nm (105 inch lbs.) .
Rotate pump by hand to check for freedom of movement.
Position pulley on pump. Install screws and tighten to 30 Nm (250 inch lbs.) .
Install accessory drive belt.
Install right front lower fender shield.
Refill Cooling System.

FOR THE 2.4 MOTOR

Disconnect negative cable from battery.
Raise vehicle on a hoist. Remove right inner splash shield.
Remove accessory drive belts.
Drain cooling system.
Support engine from the bottom and remove right engine mount.
Remove right engine mount bracket.
Remove timing belt. Refer to Engine for procedure.
Remove timing belt idler pulley.
Hold camshaft sprocket with Special tool C-4687 and adaptor C-4687-1 while removing bolt. Remove both cam sprockets.
Remove rear timing belt cover.

Install new O-ring gasket in water pump body O-ring groove. CAUTION: Make sure O-ring is properly seated in water pump groove before tightening screws. An improperly located O-ring may cause damage to the O-ring and cause a coolant leak.
Assemble pump body to block and tighten screws to 12 Nm (105 inch lbs.) . Pressurize cooling system to 15 psi with pressure tester and check water pump shaft seal and O-ring for leaks.
Rotate pump by hand to check for freedom of movement.
Install rear timing belt cover.
Install camshaft sprockets and torque bolts to 101 Nm (75 ft. lbs.) .
Install timing belt idler pulley and torque mounting bolt to 61 Nm (45 ft. lbs.) .
Install timing belt. Refer to Engine for procedure.
Install right engine mount bracket and engine mount. Refer to Engine for procedure.
Fill cooling system.
Install accessory drive belts.
Lower vehicle and connect battery cable.

Mar 29, 2012 | Cars & Trucks

1 Answer

1992 acura integra wont stay running


You need a scan tool hooked up and the fault codes read, suspect you have a crankshaft position sensor or igniter module issue going on here. Keep in mind that is just a guess so don't assume this is the problem get the testing done..

Jun 27, 2017 | 1992 Acura Integra Hatchback

1 Answer

My 2.5 V6 in 1997 Sebring Jxi runs rough after I installed a Timing belt. The code is P1391 - Crankshaft or cam shaft Position sensor. How do I fix it?


the timing is off you need to readjust it. most likely the motor is running rough because of inaccurate combustion.

Feb 07, 2011 | 1997 Chrysler Sebring

1 Answer

My car is run hot the fan don't be on when the car on it come on when I turn the car off and I just change my water pump and time belt


Please check the timing belt settings, possible it is set a little OFF and resulting in heating due to bad timing.
Secondly check the fan thermostat- thermistor sensor. This can be faulty as the fan is not coming ON. Check the fan relay and voltage from the relay.

Dec 20, 2010 | 1997 Acura TL Series

2 Answers

Replacing waterpump in1999 nissan pathfinder


Water Pump Removal & Installation To Remove:
  1. Allow the engine to cool and drain the coolant from the radiator and both engine block plugs.
  2. Remove the fan shroud and both radiator hoses.
  3. Remove the drive belts.
  4. Remove the water pump pulley.
  5. Remove the crankshaft pulley.
  6. Remove the timing belt covers.
  7. Remove the water pump.
Water pump removal/installation 7924vg20.gif

To Install:
  1. Install the water pump with new gasket.
  2. Install the timing belt covers.
  3. Install the crankshaft pulley.
  4. Install the water pump pulley.
  5. Install the drive belts and fan shroud.
  6. Install the radiator hoses.
  7. Install the coolant drain plugs.
  8. Refill the cooling system.
prev.gif next.gif

Aug 10, 2010 | 1997 Nissan Pathfinder

1 Answer

Im trying to locate my water pump on my 1995 Acura Legend where is it


6a3aa96.jpg

Fig. 1: Water pump mounting and bolt torque specifications-3.5L engine shown


REMOVAL & INSTALLATION
The radio may have a coded theft protection circuit. Make sure you have the code before disconnecting the battery, removing the radio fuse, or removing the radio.
1.8L Engines
  1. Disconnect the negative battery cable.
  2. If applicable, remove the front under panel.
  3. Gradually release the system pressure by slowly and carefully removing the radiator cap. Be sure to protect your hands with gloves or a shop rag.
  4. Drain the engine coolant into a sealable container.
  5. Remove the timing belt from the engine.
  6. Remove the camshaft pulleys and remove the back cover.
  7. Unfasten the five water pump mounting bolts, then remove the water pump.
  8. Remove and discard the old O-ring.
  9. Remove the dowel pins from the oil water pump.
  10. Clean the O-ring groove and the water pump mounting surface on the engine.

To install:
  1. Install the dowel pins to the new water pump.
  2. Position a new O-ring to the new water pump, Apply a small amount of sealant to the O-ring to hold it in position.
  3. Place the new water pump on the engine and install the mounting bolts. Tighten the mounting bolts to 104 inch lbs. (12 Nm).
  4. Install the back cover and the camshaft pulleys.
  5. Install the timing belt.
  6. Fill the engine with coolant and bleed the air from the cooling system.
  7. Connect the negative battery cable and enter the radio security code.
  8. Run the engine and check for cooling system leaks.

2.2L, 2.3L, 2.5L, 3.0L, 3.2L and 3.5L Engines
Perform this service operation with the engine cold.
  1. Disconnect the negative battery cable.
  2. Remove the front splash panel and release the system pressure by slowly removing the radiator cap.
  3. Drain the cooling system.
  4. Remove the timing belt. Inspect the timing belt for any signs of damage or oil and coolant contamination. Replace the timing belt if there is any doubt about its condition.
  5. On 1996-97 3.2 TL and 1996-00 3.5 RL models, remove the left camshaft pulley and back cover.
  6. On 1997-00 3.0 CL models and 1999-00 3.2 TL models, remove the timing belt tensioner.
  7. Remove the water pump bolts. Then, remove the water pump and sprocket assembly from the engine block. Remove the O-rings from the water passage.

To install:
  1. Before installation, be sure all gasket and O-ring groove surfaces are clean.
  2. Install the water pump with a new O-ring. Use new bolts and tighten the 6mm mounting bolts evenly to 104 inch lbs. (12 Nm) and the 8mm bolts to 16 ft. lbs. (22 Nm).
  3. If removed, install the timing belt rear cover and camshaft pulley.
  4. If removed, install the timing belt tensioner.
  5. Install the timing belt and timing belt covers.
  6. Install and adjust the tension of the accessory drive belts.
  7. Close the cooling system drain plug. Refill and bleed the cooling system.
  8. Connect the negative battery cable.
  9. Start the engine, allow it to reach normal operating temperature, check for leaks, and top off as necessary.
  10. Enter the radio security code.

Hope this helps (remember comment and rated this).

Jun 21, 2010 | 1995 Acura Legend

2 Answers

Need step by step to replace water pump on 1997 dodge caravan v-6 3,0 mits. motor...


Chrysler Caravan/Voyager/Town and Country 1996-1999 Water Pump - REMOVAL & INSTALLATION
3.0L Engine
See Figure

a812cd7.jpg

Fig. 3: Water pump mounting detail-3.0L engine
  1. Disconnect the negative battery cable.
  2. Drain the cooling system.
  3. Remove the drive belts. Remove the timing belt covers and the timing belt.
  4. Remove the water pump mounting bolts.
  5. Separate the water pump from the water inlet pipe and remove the water pump.
  6. Inspect the water pump and replace as necessary.

To install:
  1. Clean all gasket and O-ring surfaces on the water pump and water pipe inlet tube.
  2. Wet a new O-ring with water and install it on the water inlet pipe.
  3. Install a new gasket on the water pump.
  1. Install the pump inlet opening over the water pipe and press until the pipe is completely inserted into the pump housing.
  2. Install the water pump-to-block mounting bolts and tighten to 20 ft. lbs. (27 Nm).
  3. Install the timing belt and timing belt covers. Install and adjust the drive belts.
  4. Reconnect the negative battery cable. Fill the cooling system to the proper level with a 50 / 50 mixture of clean, ethylene glycol antifreeze and water.
  5. Run the engine and check for leaks. Top off the coolant level, if necessary.

Hope this help (remember comment and rated this).

Apr 13, 2010 | 1997 Dodge Grand Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...