Question about Cars & Trucks

1 Answer

Removing intake manifold

I DONT KNOW HOW TO TAKE A BRACKET OFF THATS HOLDING INTAKE MANIFOLD ON A 2002 CHEVY TRAILBLAZER

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 377 Answers

It's that big black case that runs along the right side of the engine (where the throttle body is hooked into)

Posted on Oct 18, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

psds4
  • 293 Answers

SOURCE: 1998 chevy tahoe 5.7 intake manifold removal

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528008effd
this should help

Posted on Oct 23, 2008

  • 17 Answers

SOURCE: intake manifold cover

remove oil cap steam an it should just lift off

Posted on Feb 23, 2009

LT1Rob
  • 55 Answers

SOURCE: Torque Spec for '99 Chevy C1500 5.7L engine lower intake manifold

On 5.7L engines, install the bolts and torque in sequence as follows:

  1. Step 1: 71 inch lbs. (8 Nm).
  2. Step 2: 106 inch lbs. (12 Nm).
  3. Step 3: 11 ft. lbs. (15 Nm).
f2266b6.jpg

Posted on Mar 14, 2009

  • 8 Answers

SOURCE: lower intake manifold gasket leaking 02 Olds Silhouette

This is basicly a very time consuming job rather than a physically hard one to complete. In order to replace the gasket you must remove the intake plenum,throttle body, and misc. vacuum hoses. The wiring harness connections must also be disconnected. Finally the intake manifold is exposed. The bolts holding the manifold to the block are removed exposing the leaking gasket. After removing the push rods and placing them in the correct order to be replaced the gasket and sealants can be removed. Finally replace everything in reverse order. Be sure to consult a GM manual for correct bolt torch specs. The correct specs for the manifold bolts usually come with the gasket. Make sure to change your oil a few times after this job in case any coolant entered the block. Also,change the thermostat and the oil seal on the distributor half shaft cap while you have everything off. Good Luck

Posted on May 12, 2009

  • 1 Answer

SOURCE: vacuum leak

mine is doing the same, it's your pcv receptor on the manifold. that hard plastic cover is actually part of the intake itself, if it "came off" it would cut your intake in half. that seem seals the two halfs together. you gotta pull the whole intake off and replace it... or jimmy rig it.

Posted on May 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove 93 ford probe intake manifold


2.0 or 2.5?
here is 2.0
if you need more just let me know
  1. Disconnect battery ground cable, then isolate cable end with electrical tape or equivalent.
  2. Remove air intake system and fuel line mounting bracket.
  3. Disconnect throttle cable.
  4. Disconnect coolant line from idle air bypass air valve.
  5. Disconnect coolant and vacuum lines from throttle body. Mark vacuum lines for installation reference.
  6. Disconnect throttle position sensor connector.
  7. On models with automatic transaxle, disconnect idle switch connector.
  8. Disconnect brake booster vacuum line from back lefthand side of intake manifold.
  9. Disconnect EGR temperature sensor connector, if equipped.
  10. Disconnect speed control vacuum line from back righthand side of intake manifold.
  11. Disconnect EGR solenoid connectors.
  12. Remove PCV valve from cylinder head cover.
  13. Raise and support vehicle.
  14. Remove intake manifold support bracket, then the EGR pipe from intake manifold.
  15. Lower vehicle and remove intake manifold attaching bolts and nuts.
  16. Remove intake manifold and discard gasket.
Intake Manifold Tightening Sequence 42193235

  1. Reverse procedure to install. Torque bolts and nuts in sequence to 14-19 ft lb.
My name is Tim and I work for a company called AutoEcu1 We specialize in many different controllers such as abs ebcm ecu ecm tcu tcm climate controllers dash clusters speedometers and so much more. If you need further assistance on this or any other vehicle please post here or call us at 800 921 9060 good luck!
Regards,
-Tim

Jan 09, 2015 | 1993 Ford Probe

1 Answer

Replace no 3 coil


if im not mistaken the number 3 coil is on the right hand side of the motor so you will need to remove the intake manifold to gain access to it.
Intake Manifold Removal
  1. Remove the engine cover (if equipped).
  2. Remove the air filter outlet pipe.
  3. Remove the positive crankcase ventilation hose.
  4. Remove the air cleaner resonator.
  5. Disconnect the throttle body electrical connectors.
  6. Disconnect the electrical connectors.
  7. Detach the vacuum hoses.
    • Press the retaining ring. (1)
    • Detach the vacuum hose. (2)

  8. Disconnect the vacuum hose.
  9. Detach the injector harness electrical connector from the intake manifold support bracket.
  10. Remove the intake manifold support bracket.
  11. Detach the engine wiring harness bracket.
  12. Detach the intake manifold support bracket.

    NOTE: Remove and discard the O-ring seal.
  13. Detach the throttle body.
    • Remove the retaining bolts.
  14. Remove the intake manifold.
    • Remove and discard the intake manifold gaskets.

Apr 22, 2012 | 2003 Jaguar X-Type

1 Answer

Starter needs to be replaced. Need instruction procedure for a do it yourselfer.


Hi, I have pasted the procedure from autozone.com below. Because this requires removal of the intake manifold, please be as sure as possible that your starter needs replacement. If you have any doubt, please let me know what your symptoms are and what troubleshooting you have done that led you to believe your starter is bad. Also, if you have any questions about the procedure below, please let me know. Thanks for using FixYa.


Removal & Installation


Disconnect the Negative battery cable


Relieve the fuel system pressure (you can do this by placing a rag over the schrader valve on the fuel rail and pressing in the valve stem--just be careful not to spray fuel on your eyes).


Drain the cooling system.


Remove or disconnect the following:


  • Intake manifold heat shield
  • Sight shield
  • Coil module connectors from the coil modules located on the valve covers
  • Positive Crankcase Ventilation (PCV) hose and valve from the valve cover
  • Fuel regulator vacuum tube
  • Vacuum tubes from the AIR solenoid
  • Fuel inlet and return lines
  • Fuel rail bracket retaining nut at the rear lift bracket
  • 2 pushnuts attaching the engine coolant heater wire and set it aside, if equipped
  • Fuel injector electrical connections
  • Fuel rail and injectors
  • Plenum duct clamp at the rear of the intake manifold, loosen
  • Intake manifold bolts and the manifold
Clean the manifold mating surfaces.


Remove or disconnect the following:
Starter electrical connectors Starter motor

jturcotte_1382.gif


Fig. View of starter motor removal and wires



To install:

Install or connect the following:

  • -S- terminal wire. Torque the nut to 35 inch lbs. (4 Nm).
  • Starter electrical connectors. Torque the nut to 89 inch lbs. (10 Nm).
  • Starter motor
  • Mounting bolts. Torque the bolts to 22 ft. lbs. (30 Nm).


jturcotte_1383.gif


Fig. Intake manifold torque sequence- 4.6L engines

  1. Grease the inside edge of the rubber plenum duct.
  2. Position the intake manifold by performing the following sub-steps:
    1. Place the rear of the intake manifold into the plenum duct.
    2. Place the front of the intake manifold downward on to the cylinder heads.

  3. Install the intake manifold bolts and torque to 89 inch lbs. (10 Nm) in the sequence illustrated. DO NOT torque the intake manifold bolts when the engine is HOT or at operating temperature.
  4. Make sure the plenum duct is fully attached to the rear of the intake manifold and tighten the plenum duct clamp to 20 inch lbs. (2.25 Nm).
  5. Install or connect the following:

    Fuel rail and injectors and tighten the rail retainers to 89 inch lbs. (10 Nm) Fuel injector electrical connections Alternator coolant pipe/surge tank pipe and position onto the fuel rail studs Engine coolant heater wire onto the studs and install the pushnuts, if equipped Fuel rail bracket retaining nut at the rear lift bracket and tighten to 89 inch lbs. (10 Nm) Fuel inlet and return lines Vacuum tubes to the AIR solenoid Fuel regulator vacuum tube Positive Crankcase Ventilation (PCV) valve and hose to the valve cover Coil module connectors to the coil modules located on the valve covers Sight shield Intake manifold heat shield Negative battery cable
  6. Fill and bleed the cooling system.

Mar 31, 2011 | 2002 Cadillac Deville

1 Answer

How to replace an intake manifold gasket on a 1996 gmc jimmy


Hello,

Here is a detailed summary on the procedure of how to replace the intake manifold gasket on a 1996 gmc jimmy;
REMOVING THE UPPER INTAKE MANIFOLD(PLENUM)
STEP 1 Disconnect Battery (may not be absolutely necessary, but a good practice to avoid shorting a positive wire to ground).


STEP 2 Remove serpentine belt.

STEP 3 Drain the coolant.

STEP 4 Remove air cleaner ducting and disconnect wires.

STEP 5 Disconnect throttle linkage and bracket.

STEP 6 Disconnect cruise control cable.

STEP 7 Remove brake booster vacuum hose at manifold.

STEP 8 Remove PCV hose.

STEP 9 Remove ignition coil and bracket.

STEP 1O Remove purge solenoid and bracket.

STEP 11 Relieve fuel pressure at test port.

STEP 12 Remove fuel lines and bracket.

STEP 13 Remove upper intake manifold.

REMOVING THE LOWER INTAKE MANIFOLD
STEP 1 Remove the distributor and label the spark plug wires.

STEP 2 Remove heater hoses and bypass hose.

STEP 3 Remove upper radiator hose.


STEP 4 Remove EGR valve?

STEP 5 Remove sensors and bracket on right side.

STEP 6 Remove EGR tube, clamp and bolt.

STEP 7 Remove PCV valve (and replace).

STEP 8 Unbolt A/C compressor and move it aside.

STEP 9 Loosen compressor bracket and slide forward, but do not remove it.

STEP 10 Remove alternator bracket bolt (or remove alternator and set aside)

STEP 11 Unplug all vacuum lines from intake manifold.


STEP 12 Unplug all electrical connectors from manifold.

STEP 13 Take note of the intake manifold bolts and mark the location of the bolts.


STEP 14 Remove intake manifold bolts, and manifold.

STEP 15 Clean mating surfaces

THE MAIN INSTALLATION
STEP1 Set the new gaskets in place and apply silicone to flat areas on front and rear of engine block.

STEP2 Apply thread locking compound to manifold bolts.

STEP 3 Install the manifold and tighten bolts to 35 ft-lbs, in proper sequence.

STEP4 Install the distributor.

STEP5 Install the upper intake manifold.



The remaining installation procedures are basically the reverse of removal.


Have a nice day.

Dec 04, 2010 | 1996 GMC Jimmy

1 Answer

How to remove intake manifold on 2005 Buick Lesabre


You didn't post the size of your engine so please pick the appropriate one:

3.8L
  1. Relieve the fuel system pressure.
  2. Drain the cooling system.
    1. Remove or disconnect the following:
    2. Negative battery cable
    • Supercharger
    • Thermostat housing
    • Exhaust Gas Recirculation (EGR) tube at the intake manifold
    • Engine Control Temperature (ECT) sensor
    • Intake manifold
  • To install:

    1. Install or connect the following:
      • Intake manifold with new gaskets. Torque the bolts, working from the center out, to 11 ft. lbs. (15 Nm).
      • ECT sensor connector
      • EGR tube to the intake manifold
      • Thermostat housing
      • Supercharger
      • Negative battery cable
    2. Refill and bleed the cooling system.
    3. Run the engine and check for leaks and proper engine operation.
    4.6L
    4.6L Engine
    1. Remove the brake booster hose from the throttle body.
    2. Remove the fuel pressure regulator vacuum tube from the fuel pressure regulator and the water crossover.
    3. Remove the PCV fresh air feed tube from the camshaft cover and the throttle body.
    4. Remove the PCV dirty air tube from the PCV orifice in the right camshaft cover and from the intake manifold.
    5. Disconnect the fuel injector electrical connectors from the fuel injectors.
    6. Remove the fuel injector wiring harness.
    7. Remove the fuel rail bracket nut from the engine lift bracket.
    8. Remove the fuel rail studs.
    9. Lift and remove the fuel rail with injectors.
    10. Loosen the plenum duct clamp in order to remove the intake manifold.
    11. Remove the intake manifold bolts.
    12. Remove the intake manifold.

    To install:

    1. Install the intake manifold, fitting the plenum duct over the intake manifold duct.
    2. Loosely install the intake manifold bolts.

    // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 45; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos'; c17hydro_21.gif

    Intake manifold torque sequence-4.6L engine


    1. Tighten the intake manifold bolts in sequence. Tighten the intake manifold bolts to 89 inch lbs. (10 Nm).
    2. Tighten the plenum duct clamp to the intake manifold. Tighten the plenum duct clamp to 24 inch lbs. (2.75 Nm).
    3. Inspect the fuel injector O-rings. Ensure the fuel injector O-rings are not missing, misaligned or damaged. Replace the O-rings if necessary.
    4. Lubricate the intake manifold fuel injector bores with light mineral oil (GM P/N 9981704), clean engine oil, or equivalent.
    5. Install the fuel rail with fuel injectors as an assembly.
    6. Install the fuel rail studs. Tighten the fuel rail studs to 80 inch lbs. (9 Nm).
    7. Install the fuel rail bracket nut to the engine lift bracket. Tighten the fuel rail bracket nut to 89 inch lbs. (10 Nm).
    8. Install the fuel injector wiring harness.
    9. Connect the fuel injector electrical connectors to the fuel injectors.
    10. Install the PCV dirty air tube to the PCV orifice in the right camshaft cover and to the intake manifold.
    11. Install the PCV fresh air feed tube to the camshaft cover and the water crossover.
    12. Install the fuel pressure regulator vacuum tube to the fuel pressure regulator and the throttle body.
    13. Install the brake booster hose to the throttle body.

    Nov 13, 2010 | Buick LeSabre Cars & Trucks

    1 Answer

    Diagram on how to remove and install a spider fuel injector core on a 1994 chevy blazer s10


    Here is the removal procedure, and the procedure is the same for both the V-6 and the V-8 Vortec engines. Also, be certain to put engine oil on the "o"-ring seal for the fuel injector assembly before installing the upper intake. Let me know if you require any further assistance.

    REMOVAL:

    1. Disconnect the battery negative cable assembly from the battery negative terminal.

    2. Remove the air cleaner assembly.

    3. Remove the wiring harness connectors and the brackets and move aside.

    4. Remove the throttle cable and the bracket from the upper intake manifold.

    5. Remove the cruise control cable, (if equipped).

    6. Remove the fuel lines from the intake to the rear of the block.

    7. Remove the ignition coil and the bracket.

    8. Remove the upper intake manifold.

    INSTALLATION:

    1. Install the upper intake manifold gasket.

    2. Install the upper intake manifold. Use care not to pinch the injector lines between the upper and lower intake manifolds.

    3. Install the upper intake manifold bolts. Note the marks made at disassembly for proper stud location. Install the two corner studs first in order to help align the two halves. NOTE: Other than the two torque passes listed below, the OE Manufacturer did NOT address or supply a bolt tightening sequence for the upper Intake Manifold for this model year, or other model years where this 2 piece manifold setup is used. A "Play It Safe" final tightening sequence would be to tighten from the center most bolts to the outer most bolts.

    4. Tighten the bolts in two steps: a. Tighten the bolts on the first sequence to 5 Nm (44 inch lbs.). b. Tighten the bolts on the final sequence to 10 Nm (88 inch lbs.).

    5. Install the purge solenoid and bracket.

    6. Install the ignition coil and bracket.

    7. Install the PCV hose et the upper intake manifold.

    8. Install the fuel lines from the intake at the rear of the block.

    9. Install the cruise control cable (if equipped).

    10. Install the throttle cable and bracket from the upper intake manifold.

    11. Install the wiring harness connectors and brackets.

    12. Install the air cleaner assembly.

    13. Connect the battery negative cable assembly to the battery negative terminal. - Tighten the bolt to 15 Nm (11 ft. lbs.).


    2640099.jpg

    8a054ef.jpg

    Oct 22, 2010 | Chevrolet Blazer Cars & Trucks

    1 Answer

    What is the torque specifications for the intake manifold for my Lincoln Ls V6 2002


    Upper intake manifold bolts : 89 in.lb. Lower intake manifold bolts : 89 in.lb. Thottle body bolts :89 in.lb. Front intake manifold support nut:89 in.lb. Upper intake support bracket nuts :53 in.lb. Reference:Service manual if you need further assistance please let me know and i will be glad to assist you further. If this has assisted you please feel free to rate the solution thanks -Midwest-tek

    Aug 27, 2010 | 2002 Lincoln LS

    2 Answers

    Need to replace the intake manifold


    3.8L Engine (most common) Upper Intake Manifold To Remove:
    1. Drain the cooling system.
    2. Remove or disconnect the following:
      • Negative battery cable.
      • Fuel injector sight shield.
      • Air cleaner intake duct.
      • Right spark plug wires from the ignition control module and reposition.
    3. Relieve the fuel pressure.
    4. Remove or disconnect the following:
      • Fuel rail assembly.
      • Brake booster hose from the vacuum source manifold in the upper intake manifold.
      • Exhaust Gas Recirculation Valve (EGR) wiring harness heat shield nut, bolt and the EGR heat shield.
      • Throttle body support bracket upper bolt.
    5. Disconnect the electrical connectors from the following:
      • EVAP purge solenoid
      • Throttle Position (T/P) sensor
      • Idle Air Control (IAC) valve
      • Manifold Absolute Pressure (MAP) sensor
      • Mass Air Flow (MAF) sensor
      • EVAP purge solenoid vacuum line from the throttle body.
      • Accelerator and the cruise control cables with the bracket from the throttle body.
    6. Remove or disconnect the following:
      • Upper intake manifold bolts and stud.
      • Clean the upper intake manifold bolt threads.
    7. Remove or disconnect the following:
      • Upper intake manifold by lifting the back of the intake and sliding the manifold forward from the throttle body support bracket.
      • Upper-to-lower intake manifold carrier gasket from the upper intake manifold.
    8. If the upper intake manifold is being replaced, remove the following:
      • Throttle body assembly.
      • Manifold Absolute Pressure (MAP) sensor.
      • Positive Crankcase Ventilation (PCV) valve.
      • Vacuum source manifold.
    Upper intake manifold bolt torque sequence (3.8L engine) gm-03-38-530.gif

    To Install:
    1. If the manifold was replaced, install or connect the following:
      • Vacuum source manifold.
      • Positive Crankcase Ventilation (PCV) valve.
      • Manifold Absolute Pressure (MAP) sensor.
      • Throttle body assembly.
      • Upper-to-lower intake manifold carrier gasket to the upper intake manifold.
    2. Carefully place the upper intake manifold onto the lower intake manifold. Ensure that the alignment pins in the upper intake manifold align with the holes in the lower intake manifold. NOTE: Apply thread lock compound, to the bolt threads before assembly.
    3. Install or connect the following:
      • Upper intake manifold. Tighten the upper intake manifold bolts in sequence to 89 in lbs (10 Nm)
      • Accelerator and the cruise control cables with the bracket to the throttle body.
      • EVAP purge solenoid vacuum line to the throttle body.
    4. Connect the electrical connectors to the following:
      • Mass Air Flow (MAF) sensor
      • Manifold Absolute Pressure (MAP) sensor
      • Idle Air Control (IAC) valve
      • Throttle Position (T/P) sensor
      • EVAP purge solenoid
    5. Install or connect the following:
      • Throttle body upper support bracket bolt. Tighten the bolt to 89 in lbs (10 Nm)
      • EGR valve wiring harness heat shield, nut and the bolt. Tighten the nut and the bolt to 89 in lbs (10 Nm)
      • Brake booster hose to the vacuum source manifold.
      • Fuel rail assembly.
      • Right spark plug wires.
      • Air cleaner intake duct.
      • Fuel injector sight shield.
    6. Connect the negative battery cable.
    7. Fill the cooling system.
    8. Inspect for fluid or vacuum leaks.
    Lower Intake Manifold (W/O Supercharger) To Remove:
    1. Remove or disconnect the following:
      • Upper intake manifold.
      • Generator brace.
      • Drive belt tensioner with the mounting bracket and the heater water bypass inlet pipe.
      • Exhaust gas recirculation EGR outlet pipe bolt from the lower intake manifold.
      • Radiator inlet hose from the water outlet housing.
      • ECT sensor electrical connector.
      • Right upper engine mount strut bracket.
      • Generator brace bracket bolts.
      • Generator brace bracket.
      • Lower intake manifold bolts.
      • Lower intake manifold.
      • Lower intake manifold seals.
      • Lower intake manifold gaskets.
    2. If replacing the lower intake manifold, Remove or disconnect:
      • Water outlet housing bolt and stud
      • Water outlet housing
      • Gasket and the thermostat.
      • ECT sensor.
    3. Inspect the flatness of inlet flanges.
    4. Clean the intake manifold mating surfaces.
    5. Clean the intake manifold bolts and bolt holes of adhesive compound.
    To Install:
    1. If removed, install the ECT sensor.
      • Tighten the ECT sensor to 18 ft. lbs. (25 Nm)
    2. If removed, install the thermostat, the gasket, and the water outlet housing.
    3. If removed, install the water outlet housing bolt and the stud.
      • Tighten the bolt and stud to 20 ft. lbs. (27 Nm)
    4. Install or connect the following:
      • Lower intake manifold gaskets. NOTE: Apply sealer GM P/N 12346286 (Canadian P/N 10953472) or equivalent to the ends of the intake manifold seals.
      • Lower intake manifold seals.
      • Lower intake manifold.
      • Lower intake manifold bolts.
      NOTE: Apply thread lock compound GM P/N 12345382 (Canadian P/N 10953489) or equivalent to the two hidden bolts and ensure they are installed.
    5. Tighten the lower intake manifold bolts in sequence to 11 ft. lbs. (15 Nm) gmpc_v6_5.gif

    6. Install or connect the following:
      • Generator brace bracket.
      • Generator brace bracket bolts. Tighten the bolts to 37 ft. lbs. (50 Nm)
      • Right upper engine mount strut bracket.
      • ECT sensor electrical connector.
      • Radiator inlet hose to the water outlet housing.
      • EGR outlet pipe to the lower intake manifold.
      • EGR outlet pipe bolt to the lower intake manifold. Tighten the bolt to 21 ft. lbs. (29 Nm)
      • Drive belt tensioner.
      • Generator brace.
      • Upper intake manifold.
    7. Inspect for leaks.
    Lower Intake Manifold (W/ Supercharger) To Remove:
    1. Disconnect the negative battery cable.
    2. Drain the cooling system.
    3. Remove the supercharger.
    4. Remove the thermostat housing.
    5. Remove the EGR pipe at the intake manifold.
    6. Disconnect the electrical connection at the temperature sensor.
    7. Remove the intake manifold and gaskets.
    NOTE: The coolant bypass tube will release from the intake manifold when the manifold is removed.
    To Install:
    1. Clean the gasket sealing surfaces.
    2. Install the intake manifold gaskets.
    3. Align the coolant bypass tube with the opening in the intake manifold and install the manifold. Tighten the bolts to 11 lb ft (15 Nm).
    4. Install the electrical connector to the temperature sensor.
    5. Install the EGR pipe to the intake manifold.
    6. Install the thermostat housing.
    7. Install the supercharger.
    8. Fill the cooling system.
    9. Connect the negative battery cable.

    Aug 05, 2010 | 1997 Pontiac Grand Prix

    1 Answer

    Need to replace intake manifold how do you do this


    Bonneville, LeSabre, Park Avenue 2000-2005 Intake Manifold - Removal & Installation

    3.8L Engine
    VIN 1 Engine
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Relieve the fuel system pressure.
    3. Drain the cooling system.
    4. Remove or disconnect the following:
      Negative battery cable Supercharger Thermostat housing Exhaust Gas Recirculation (EGR) tube at the intake manifold Engine Control Temperature (ECT) sensor Intake manifold
    To install:
    1. Install or connect the following:
      Intake manifold with new gaskets. Torque the bolts, working from the center out, to 11 ft. lbs. (15 Nm). ECT sensor connector EGR tube to the intake manifold Thermostat housing Supercharger Negative battery cable
    2. Refill and bleed the cooling system.
    3. Run the engine and check for leaks and proper engine operation.

    VIN K Engine
    1. Before servicing the vehicle, refer to the Precautions section.
    2. Disconnect the negative battery cable.
    3. Drain the cooling system.
    4. Relieve the fuel system pressure.
    5. Remove or disconnect the following:
      Fuel injector sight shield Air inlet duct Spark plug wires from the right side Manifold Absolute Pressure (MAP) sensor Vacuum lines from the intake manifold Fuel lines Fuel injector electrical connectors Fuel regulator vacuum line Fuel rail from the intake manifold Exhaust Gas Recirculation (EGR) heat shield Throttle cable bracket from the cylinder head mounting bracket and the throttle body cables Throttle body support bracket Upper intake plenum and gasket Thermostat housing Electrical connector from the Engine Coolant Temperature (ECT) sensor Drive belt tensioner assembly EGR valve outlet pipe Lower intake manifold

      a5adffa.jpg
      Fig. Exploded view of the intake manifold and related components-3.8L (VIN K) engine
    To install:


    140d431.jpg
    Fig. Upper intake manifold torque sequence-3.8L (VIN K) engine


    4950e4f.jpg
    Fig. Lower intake manifold torque sequence-3.8L (VIN K) engine
    1. Install or connect the following:
      Intake manifold using new manifold gaskets. Torque the bolts in sequence to 11 ft. lbs. (15 Nm); then, re-torque to 11 ft. lbs. (15 Nm). EGR valve outlet pipe Drive belt tensioner assembly. Torque the tensioner bolts to 37 ft. lbs. (50 Nm). Electrical connector to the ECT sensor Thermostat housing Upper intake plenum. Torque the intake plenum bolts to 88 inch. lbs. (10 Nm). Throttle body support bracket Throttle cable bracket to the cylinder head mounting bracket and the cables to the throttle body lever EGR heat shield Fuel rail. Torque the fuel rail bolts to 88 inch. lbs. (10 Nm). Fuel lines Fuel regulator vacuum line Fuel injector electrical connectors Vacuum lines to the intake manifold MAP sensor Spark plug wires Fuel injector sight shield and air inlet duct Negative battery cable
    2. Refill and bleed the cooling system.
    3. Run the engine and check for leaks and proper engine operation.

    Hope this help (remember rated this).

    May 17, 2010 | 2001 Pontiac Bonneville

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    117 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    75117 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...