Question about 1988 Jeep Cherokee

1 Answer

I have a 97 olds 88 how do I change the ignition switch with diagram

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 377 Answers

Up under dash, mounted basically on the side of the steering column

2 screws hold it to the column. sometimes easier to remove the nuts holding column up to dash, lower column down some till wheel on seat.

You remove the 2 small bolts holding switch to column, then there is a rod in the back for the key. Lift switch off rod, Alig new switch back on rod and mount new switch back on the column

It is adjustable to need to eb 100% you have it adjusted so it does NOT start in reverse or any other gear. Only park and neutral


its the top left in picture, shown.. tilt and non tilt very clse to same

Posted on Oct 18, 2013

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 14036 Answers

SOURCE: How too change the ignition switch on a 88

disconnect negative battery cable.place the ignition lock in the off lock position. remove the 2 switch mounting screws.disconnect the switch from the rod.disconnect the wiring and remove the switch.TO INSTALL.ignition switch installation for non tilt columns.move the the ignition switch slider to the off unlocked position move the slider all the way down.then back 2 clicks.the remote rod hole in the ignition switch slider should now be centered.insert the remote rod in the ignition switch slider hole and install the ignition switch on the steering column.tighten the attaching screws to 35 inch lbs.ignition switch installation for tilt columns.insert the ignition key in the lock cylinder and turn the cylinder to the off unlock position.move the ignition switch downward to eliminate any slack and tighten the attaching screws to 35 inch lbs.

Posted on Nov 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram for 97 camaro ignition switch


Hello,
my 97 LT1 chevy camaro is giving me ignition problems.
I changed the relay box and now cannot turn the key. It's like there is no thread. ?.. someone please help

Sep 09, 2010 | Chevrolet Camaro Cars & Trucks

1 Answer

What is the firing order of the 3.8L engine in a 92 olds 88? Changing spark plug wires & must have switched order


1992 Oldsmobile Delta 88 3.8 liter V-6 VIN "L" - Identifying Ignition Types I and II

On Type I coil packs, three twin tower ignition coils are combined into a single coil pack unit.

5582ccc.gif


On Type II coil packs, the coils can be replaced separately and the ignition wires are all on the same side of the coil pack.

With Type I Ignition


669dd08.gif


With Type II Ignition

d6a3659.gif

Hope helps (remember comment and rated this).

Jun 18, 2010 | 1992 Oldsmobile 88

1 Answer

Need diagram for steering column for 97 ford


if the key turns fully as it suppose to the electrical ignition switch is at fault

Apr 02, 2010 | 1997 Ford Taurus

1 Answer

Location of fuel relay switch for 97 olds 88


Hello! The fuel pump relay switch is located on the firewall under a plastic cover...It is a black plastic 1"x1"
switch...It is designed to operate the fuel pump for 3-8 seconds when you turn the ignition switch on, to prime the injector rail...

Guru..............saailer

Feb 27, 2010 | 1997 Oldsmobile Eighty Eight

2 Answers

97 Olds 88 Wont Start


try replacing some fuses..... email me a pic of the fuse panels paul.o39neal@yahoo.com

Jun 24, 2009 | 1997 Oldsmobile 88

1 Answer

97 Oldsmobile 88 popping noise


Tie rod ends or frame cradle mounts

Jun 01, 2009 | 1997 Oldsmobile Eighty Eight

1 Answer

Firing diagram for a 87 olds delta 88 3.8


1987 Oldsmobile Delta 88
3.8 liter V-6 VIN "3" Identifying Ignition Types I and II


119d8a7.gif
On Type II coil packs, the coils can be replaced separately and the ignition wires are all on the same side of the coil pack.

With Type I Ignition

c6cc640.gif
With Type II Ignition

7722088.gif

Apr 02, 2009 | 1987 Oldsmobile Delta 88

1 Answer

Ignition switch


Whoa....first, the ignition swith is not a part of the tumbler. you went in to far. replace the switch and put the brass gear on the tumbler. slide the tumbler out and install the keeper. the tumbler needs to be in the "on" position..

Oct 21, 2008 | 1997 Ford F150 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

92 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...