Question about 2008 Toyota Highlander

1 Answer

Replace rear wiper assembly - 2008 Toyota Highlander

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 21 Answers

The wiper arm has a cover on the left end that pops up after gently spreading the two bottom sides apart. That allows the arm to swing out for cleaning the window or replacing the blade.
The wiper blade assembly attaches to the end of the arm . It is pressed in and will pop out with a little force rotating the left side away from the arm. It pops back in with a little push. The arm remains attached to the rotating shaft assembly.
I believe you can then replace just the rubber blade and not the whole blade assembly, if that is your fancy.
Dave

Posted on Nov 10, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 expedition rear wiper and washer doesn't work


The rear wiper motor assembly may be defective/seized. You can try turning on the rear wiper and moving the wiper arm with your hand to see if it will move even a little bit. If you can coax it to move, the wiper motor is bad and needs replacement. If it doesn't move, you will have to disassemble the rear hatch panels and test the motor directly for power and ground.

Jun 21, 2015 | Cars & Trucks

2 Answers

How do I fix or replace the rear wiper motor


Hello,

  1. Disconnect the cable running to the negative terminal on the car's battery. To do this, loosen the nut on the cable clamp until the clamp is loose enough for you to slide the cable clamp off the negative battery terminal.
  2. Pull the wiper arm away from the rear windshield until the wiper arm locks into a vertical or semi-vertical position or is perpendicular to the rear windshield.
  3. Remove the nut holding the wiper arm assembly to the rear wiper motor.
  4. Pull the wiper arm off the wiper motor assembly.
  5. Unplug the rear wiper motor plug/harness.
  6. Remove the screws holding the rear wiper motor to the inside of the vehicle at the base of the rear window.
  7. Pull the rear wiper motor off.
  8. Install the new wiper motor and put the wiper motor and arm assembly back on the vehicle by reversing the completed steps.
From ehow.com

I hope this helps

Mar 21, 2011 | 2000 Ford Expedition

1 Answer

The rear window wiper blade holder is rusted how do I remove it for replacement?


Three things you can replace depend on your budet
1) you can replace whole wiper blabe assembly by lift up the cover at the bottom end of the bale assembly and un-screw the nut and raplace whole assembly with arm , wiper insert etc ... with the new one This way cost you more.
2) on hte middle of the whole wiper blade assy has the flexible section, you can un-screw 2 small philipe pan head screw with screw driver and disconnect the top section with the wiper blade insert (rubber)
3) slide wiper blade insert out of the holder, becareful with 2 small steel blade will hole your rubber insert inside the wiper frame. Slide new rubber insert in the frame .

Feb 25, 2011 | 1995 Toyota Supra

1 Answer

How to remove the rear wiper cover on a 2008 saturn vue


2008 Saturn Vue rear wiper blade: Pop off the cover over the bolt that comes out of the rear window. Unscrew the nut. Now you can remove the assembly. Give the old wiper a tug and pull it out. Snap in a new 11-inch wiper. Replace the assembly, bolt and cover.

Dec 03, 2010 | 2008 Saturn VUE

3 Answers

How easy is it to replace the front wiper motor on a 2004 ford escape ? Where is it located ?



Front Wiper Motor
Removal & Installation

NOTE A new wiper motor assembly comes with the linkage arm installed.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove the windshield wiper mounting arm and pivot shaft
    WARNING Do not remove the wiper motor linkage arm from the wiper motor assembly. If the arm is removed, the wiper arms may not park in the correct location.
    NOTE Use a suitable tool to separate the wiper linkage arm from the wiper mounting arm and pivot shaft assembly.
  3. Remove the 3 bolts and the wiper motor.

    7f7866e.gif

    Fig. Wiper motor and linkage

To install:
  1. Install wiper motor and bolts.
  2. Tighten wiper motor bolts to 10 ft. lbs. (13 Nm).
  3. Install windshield wiper mounting arm and pivot shaft.
  4. Check wiper operation.

Rear Wiper Motor
- Removal & Installation
  1. Remove the rear pivot arm.
  2. Remove the rear wiper motor shaft nut cover
  3. Remove the rear wiper motor shaft nut.
  4. Open the lift gate window.
  5. Remove the rear wiper motor cover trim panel.
  6. Disconnect the electrical connector.
  7. Remove the 2 rear window wiper motor nuts
  8. Remove the rear window wiper motor.

    79be491.jpg
    Fig. Rear wiper motor view-2008 model shown, other years similar

To install:
  1. Install rear wiper motor and tighten mounting nuts to 62 inch lbs. (7 Nm).
  2. Reconnect the electrical connector.
  3. Install wiper motor cover trim panel.
  4. Install rear wiper pivot arm tighten nut to 53 inch lbs. (6 Nm).
  5. Install shaft nut cover.
  6. Check wiper operation.

Good luck (remember rated this post).

Feb 25, 2010 | 2004 Ford Escape

2 Answers

How do you replace the rear wiper blade on the 2008 Saturn Vue. The deal wants 30.00 to replace it. Plus do you know where you can buy a replacement besides the dealership for 20.00?


any auto parts store-even wal-mart sells the wiper blades they are a standard length and clip into place most auto stores can assist u as how to put one one--prices run from cheap $ 3.00 to extreme condition $10.00

Feb 22, 2010 | 2008 Saturn VUE

1 Answer

How do you replace the rear windshield wiper blade? I bought a 13" wiper blade but I couldn't figure out how to change it.


like most hatchbacks, you hafta replace the whole rear wiper arm assembly. Go to a Toyota dealers' parts counter.

Jan 16, 2010 | 2005 Scion xA

1 Answer

Can't remove rear wiper to replace on 96 caravan


Lift wiper arm from rear window. then release latch that holds the blade to the wiper arm.( It's small tab)

Jan 16, 2010 | 1996 Dodge Caravan

1 Answer

How to replace the wiper insert at the back of


moz-screenshot.jpg
  1. REMOVE RR WIPER BLADE
    1. Raise the rear wiper blade to the position as shown in the illustration where the meshing of the claw disengages with a clicking sound. NOTE: Be careful not to break the claw.
    2. Pull straight the rear wiper blade to vehicle's left from the wiper arm. NOTE: Do not fold the rear wiper arm with the rear wiper blade removed from it.1722d05.gif

  1. REMOVE REAR WIPER RUBBER
    1. Place the rear wiper with the rear end of the rubber protruded from the blade stopper as shown in the illustration. NOTE: Do not pull out the wiper rubber forcibly, as the backing plates will become deformed or the blade claws will become damaged. HINT: The rubber can be easily pulled out by pushing the middle area of the blade.
f54b10a.gif
  1. INSTALL REAR WIPER RUBBER
    1. Install the 2 wiper rubber backing plates to the rear wiper rubber. NOTE: Be careful to observe and keep direction of curvature for correct replacement.
0dd144d.gif
b. Insert the rear wiper rubber from the claw of the middle of the rear wiper blade into the rear end position.
8f40009.gif
c. After passing the rear wiper rubber through the rear end side claw, protrude it from the rear end stopper and pass it through the front tip side claw.

Sep 12, 2009 | 2005 Toyota Matrix

1 Answer

Driver's side wiper arm on my '93 Sidekick is not working


This is what I Found there was not any Illustration's with it looks Fairly simple, Good luck



FRONT
  1. Disconnect linkage assembly from wiper motor shaft.
  2. Disconnect electrical connectors from wiper motor.
  3. Remove wiper motor attaching bolts, then wiper motor.
REAR
  1. Remove wiper blade and arm assembly.
  2. Remove access panel on back door.
  3. Disconnect linkage assembly from wiper motor shaft.
  4. Disconnect electrical connectors from wiper motor.
  5. Remove wiper motor attaching bolts, then wiper motor.
Skill
Level
Mfg.
Warranty
Standard Wiper Motor Labor Replace Front B 0.7 1.0
PLEASE DONT FORGET TO RATE ME Thank You Much

Jan 20, 2009 | 1995 Suzuki Sidekick

Not finding what you are looking for?
Cars & Trucks Logo

226 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...