Question about 2000 Daewoo Korando

Open Question

Elect fault in 4 wheel drive. 4 wheel drive not working & 4wheel drive light on. can you show drawings for electrical system for the 4 wheel drive?

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2014 kodiac450 starts missing on acceleration when in differential lock?


check the power draw for the diff lock system as it appears that the current draw is robbing the ECM of enough power to work and run the engine. You may have to have the alternator bench tested for current output. Check condition and tension of drive belt.

Dec 08, 2014 | Cars & Trucks

1 Answer

Lincoln Navigator 4wheel drive 1998


See that this is an old problem. Some of the knobs could crack on the backside and allow the knob to rotate on the shaft without turning the shaft at all. If the knob is okay then go underneath the vehicle and disconnect the electric plug on the shift solenoid and Inspect for corrosion on the terminals. There is a problem which can happen if an indicator light burns out in the electric shift models. The length of the shift solenoid plunger is what determines whether you are in 2 wheel or 4 wheel drive, or high or low range. If the indicator light burns out, it changes the electric power and position of the shift solenoid plunger.

Dec 03, 2014 | 1998 Lincoln Navigator

1 Answer

4WD system on jeep will not work when the temp drops below freezing


there maybe some dirst in the sensor - try cleaning it

Nov 20, 2014 | 2009 Jeep Liberty

1 Answer

No light on 4wheel dr control


There are a few things that would cause this problem.
The first and most common would be the switch itself is bad. the next would be a bad 4wheel drive encoder motor, this is the motor on the transfer case that is used to operate the 4wheel drive. The last would be the 4 wheel drive module.
You will need to do some testing, if the four wheel drive is working and goes in and out of 4 wheel drive then i would say it the switch. if it does not work correctly it may still be the switch or one of the components i listed above.I have enclosed a wiring diagram, you will need to do some testing to check system, first make sure all fuses are good. the fuses that operate the 4wd are listed on diagram, it will also tell you the location of each part. you will need to test front axle actuator and selector motor and switch, you will need a test light and a meter. hope this is helpful, good day.4_26_2012_10_13_14_pm.gif

Apr 26, 2012 | 2002 GMC Envoy

2 Answers

2000 suzuki grand vitara 4 wheel drive will not engage


2000 Suzuki Grand Vitara rear Wheel Drive working but 4wheel
is not working, dash 4wheel sign light not working

Jan 12, 2011 | 2000 Suzuki Grand Vitara

1 Answer

I have a service 4wheel drive light. What should I check?


The 4 wheel drive system has detected a problem that has generated a diagnostic trouble code. The fault will need to diagnosed with a scan tool that interfaces with the onboard computer. There is no other method of diagnosing this problem.

Mar 28, 2010 | 1999 Chevrolet Blazer

1 Answer

No 4 wheel drive, no dash lights, no tail lights!


check your relays first (after the fuses) and the vacuum lines if you have those for the 4 wheel drive. Hope that helps

Mar 29, 2009 | 1995 Chevrolet S-10 CA Edition

1 Answer

The 4wheel drive light is flashing on the dash.


the light is flashing to let u know a fault has occurred in the transfer case electronic control system, most likely the transfer case engagement motor

Jan 07, 2009 | 1995 Ford Explorer

1 Answer

1994 explorer 4 wheel drive


Since it seems no one has answered in 3 days I will say something. Some of the 4 wheel systems use vacuum to lock and unlock the 4 wheel system. There are solenoids in the transfer case which adjust the functions into 4 wheel auto, 4 wheel, and 4 wheel low settings. On the units that use electric, the electric strength or power determines how far the electric solenoid extends or travels to change gear functions. These are sensitive electric settings. A burned out dashlight factory wired into that circuit can change the result of what 4 wheel function you will receive. So will a bad connection of a plug-in to the transfer case.

A technician can test the wires to the transfer case and see what electric readings are going into the transfer case when the dash is set to the different dash settings. Besides a Dealer, a really good transmission shop can perform this test.

Dec 30, 2017 | 1994 Ford Explorer Limited

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

79077 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...