Question about 1992 Ford Taurus

1 Answer

Taurus 1993 GL 3.0 liter engine, check engine always lighted including airbag, may I know OBD1 password for diagnostic purpose

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 14,161 Answers

Posted on Dec 29, 2015

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 5 Answers

SOURCE: 1996 ford taurus GL

The air bag module monitors all of the electrical circuits of the air bag system. If it detects a fault in any of these circuits, it will cause the air bag light to come on. If it's flashing, count the number of flashes between pauses, this should be the diagnostic code the module is telling you what is wrong with the airbag system (or you can use a scan tool) The only way to keep the light off (besides removing it from dash) is to repair the fault, you can clear the code with the scantool, but it will come right back on if it still sees the fault.

Posted on Oct 01, 2008

blueextc3221
  • 15935 Answers

SOURCE: need diagram of serpentine belt for 94Solution for "need diagram for replacing serpentine belt for 94 ford taurus gl w/3 0 v6 engine and a/c" ford taurus gl w/3.0 v6 engine and a/c

89beac5.gif Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

Posted on May 21, 2009

  • 432 Answers

SOURCE: 2005 ford taurus engine light on

Try disconnecting the battery for 10 mins.This may reset the lights timer. If it comes back on within the next few days the take it to a large auto parts store and most will bring their computer out and hook it to your car and read the code the light will leave in your car computer,then they tell what the code says and try to sell you the part.You might car the auto parts store first and tell them what you have and ask if then can read your code for you.Its usually a free service.

Posted on Sep 01, 2009

emissionwiz
  • 76682 Answers

SOURCE: 1995 Ford Taurus Sho 3.2 check engine light blink

Code 33 is EGR opening not detected, this is caused by a plugged EGR exhaust passage in the upper intake manifold, this is a common SHO engine fault, the valve works but the engine does nothing that the computer can sense, since no gas flows, to verify this is the problem open the egr at idle, the engine should almost die, if nothing happens or only a tiny change in idle speed or quality the passages are plugged, if it does stall or get real rough the egr position sensor (usual code for sensor is 32) may be faulty or the valve is sticking. I was a ford dealer tech for 30 years and did quite a few of these, there is a TSB (technical service bulletin) about this problem

Posted on Oct 21, 2009

toyladi3
  • 597 Answers

SOURCE: where is the fuel filter

Hello,

The fuel filter of the 1993 ford taurus is located in front of the rear wheel well passenger side, about an inch in. There are two plastic tabs that hold the fuel lines to the filter. Just pop them out (don't use tools). You may need to push them through with something small like a screwdriver, just don't use the tool on the fuel line fittings and be careful with those lines with anything sharp.

To change it with a new one, please follow the instruction below carefully.

  1. Use a small flat screwdriver to remove the two plastic clips from the lines attached to the filter.
  2. Be careful! The lines may be under pressure, and fuel may spray out as you unplug the first line from the filter.
  3. Use a flat screwdriver, or 5/16 nut-driver to loosen the clamp from the body of the filter to remove old filter
  4. Mount the new filter into clamp & tighten (not too much - just snug). Be sure the 'flow' arrow is pointing towards the engine,
  5. Insert the new plastic line clips that are in the box with the filter into the lines and then plug the lines onto the filter until you hear them click in place.
Hope this helped. Thank You for using FixYa!!!

Posted on Jan 27, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1993 ford Taurus GL it turned off while


check ignition module on top of steering colum or the crank positing sensor bottom of engine

Sep 11, 2014 | 1993 Ford Taurus

1 Answer

Mil code 011


NO YEAR, no ENGINE stated, ?????????? what a challenge.
seen WHERE> must we guess that too>?
you connected a scan tool to the USA DLC 16pin OBD2 dash port
and scanned it and got all codes
seems not.
or did the key on.off mad DTC check.? wild key trick?

or the car is a 1993 car that runs the old OBD1 , 2 digit flash codes.
is that it? but added a 0? to confuse us?
the 1993 book is free, seen below, see page 2, emissions under diagnostics.

OBD1 code 11
means cam (cmp) or crank (CKP) are dead, or misfiring,
or that they don't agree.
as you know the cam and crank are locked together, at 2:1 ratio.
if the cam drive is not loose , then the sensor (either ) are bad.
ckp is top fail, (weak by design) the CMP is robust.

read page 3. 1993 if it is, if not, read as appropriate.
no engine stated so I'm brain dead. with this... see?
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

Jul 09, 2014 | Jeep Grand Cherokee Cars & Trucks

3 Answers

Diagnostic code po325 what does this mean


Hi the error code relates to the PCM Knock Sensor Circuit

A knock sensor tells the engine computer when one or more of your engine's cylinders are "knocking", that is, exploding the air/fuel mixture in a way that delivers less power and can be damaging to the engine if prolonged. The computer uses this information to tune the engine so that it doesn't knock. If your knock sensor wasn't operating properly, so that it was always indicating a knock, the engine computer's response may have been to change the ignition timing on your engine. The knock sensor generally threads into the engine block. This P0325 code may show up intermittently or the Service Engine light may be lit constantly.
Symptoms

You may notice drivability problems including a lack of power and perhaps some hesitation. There may also be other symptoms.
Causes

A code P0325 most likely means one or more of the following has happened:

* The knock sensor is faulty and needs to be replaced
* There is a wiring short/fault in the knock sensor circuit

Possible Solutions

* Check the resistance of the knock sensor (compare it to factory specs)
* Check for broken/frayed wires leading to the sensor
* Replace the knock sensor

Hope this helps
Steve

Mar 03, 2011 | 1993 Jeep Grand Cherokee

1 Answer

COOLING CAPACITY FOR 1993 TAURUS


1993 FORD TAURUS 3.0L 6-cyl Engine Code [Y] SHO
Engine oil, with filter..........4.7 liters
Cooling System, Initial Fill..........11 liters


Good luck and hope this helps, thank you for using fixya

Nov 04, 2010 | 1993 Ford Taurus

1 Answer

How to read engine cose 1990 ford escort 1.9


On board diagnostic (OBD) was designed on vehicles equipped with electronic fuel injection so you can generally retrieve the codes yourself. No need buying a scanner or running to any parts stores to check the engine light. This system is called obd1 and applies to most vehicles made before 1995 for domestics and 1993 on imports.
Ford owners can check their check engine light using the diagnostic connector located at the engine compartment by the fender near the battery. Getting the obd1 codes need a couple of tools: a 4 inch long gage 16 jumper wire and a 12 volt test light. Both tools are hooked up to the diagnostic connector and when the IGNITION KEY is turned on (without starting engine) the codes will begin to flash in the test light, not in the dash panel. If there is no code, you will normally get code 11 or 111. On Fords, there are 2 test modes, the KOEO (key on engine off) and the KOER (key on engine running). Both test modes should be used to get the accurate evaluation of the stored fault codes.
Most of the codes can be erased or cleared by disconnecting the battery negative terminal for 1 minute and reconnect. Just make sure to check your service manual in case you have electronic equipment such as radio or clock that needs reprogramming in which battery disconnection is not recommended. Finally after performing repairs on the culprit code, always go for a road test to confirm if the problem is fixed.
http://www.troublecodes.net/Ford/88-951325.shtml

Nov 02, 2009 | 1990 Ford Escort

1 Answer

Need to know where to find a diagram on the firing order of a 1994 ford Taurus GL with a 3.8 liter V6?


3.8L Engine Firing Order: 1-4-2-5-3-6-nl-> Distributor Rotation: Counterclockwise

5fcbbe5.jpg

Good luck.

Sep 14, 2009 | 1994 Ford Taurus

1 Answer

I have a 1993 chevy k1500 5.7 liter 4wd with a 40L60E transmission and it will not shift out of 2nd gear what could the problem be


Your truck could be on a limp mode since your transmission is controlled by the ECM. 
Here is a way for you to retrieve the fault codes in the ECM that is keeping your transmission from shifting past 2nd gear. Just be careful not to burn out the transmission.
On board diagnostic (OBD) was designed on vehicles equipped with electronic fuel injection so you can generally retrieve the codes yourself. No need buying a scanner or running to any parts stores to check the engine light. This system is called obd1 and applies to most vehicles made before 1995 for domestics and 1993 on imports. 

For GM domestic vehicles made before 1995, the diagnostic connector is located under the dash panel by the driver side. To get the check engine codes to flash in your dash panel, use a jumper wire or a paper clip and connect terminals A and B of the diagnostic connector. Turn your ignition key on with engine off and the codes should start to blink. All codes should start with code 12 which is one long flash followed by 2 short flashes. This code 12 means the diagnostic system is normal and will repeat itself continuously if there are no trouble codes. Otherwise, code 12 will flash 3 times before flashing the fault codes.

For GM and domestic vehicles and most of the codes can be erased or cleared by disconnecting the battery negative terminal for 1 minute and reconnect. Just make sure to check your service manual in case you have electronic equipment such as radio or clock that needs reprogramming in which battery disconnection is not recommended. Finally after performing repairs on the culprit code, always go for a road test to confirm if the problem is fixed.

Good luck and here is a link for the OBD 1 codes. http://chevythunder.com/199295_lt1_trouble_codes.htm#Code 28

May 03, 2009 | Chevrolet 1500 Cars & Trucks

1 Answer

93 Ford Taurus GL 3.0 V6) whrer exactly is the solenoid?


it on the starter check under the car it shoud be in the front of the engine on the dirvers side but if i were you take the start to autozone or advance and have it tested if it is the solenoid just replace the whole thing it not worth just fix the solenoid it self

Oct 09, 2008 | 1993 Ford Taurus

1 Answer

1996 ford taurus GL


The air bag module monitors all of the electrical circuits of the air bag system. If it detects a fault in any of these circuits, it will cause the air bag light to come on. If it's flashing, count the number of flashes between pauses, this should be the diagnostic code the module is telling you what is wrong with the airbag system (or you can use a scan tool) The only way to keep the light off (besides removing it from dash) is to repair the fault, you can clear the code with the scantool, but it will come right back on if it still sees the fault.

Sep 28, 2008 | 1996 Ford Taurus

Not finding what you are looking for?
1992 Ford Taurus Logo

Related Topics:

59 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

fordexpert

Level 3 Expert

5537 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...