Question about Cars & Trucks

Open Question

How to replace front wheel bearings 2007 mercury Milan

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

blueextc3221
  • 15935 Answers

SOURCE: replacing front wheel bearing

  1. Loosen the wheel nuts and the center axle nut.
  2. Raise the vehicle and safely support it.
  3. Remove the wheel. Remove the ABS speed sensor if so equipped.
  4. Unclamp the brake hose from the shock absorber, but do not disconnect the line.
  5. Remove the brake caliper and hang it out of the way on a piece of stiff wire. Do not disconnect the brake line; do not allow the caliper to hang by the hose.
  6. Remove the brake disc.
  7. Place a dial indicator near the center of the axle hub, and check the backlash in the bearing shaft direction. Maximum is 0.0020 inch (0.05mm). If the backlash exceeds the maximum, replace the bearing.
    1. Usiung a dial; indicator, check the deviation at the surface of the axle hub outside the hub bolt. Maximum is 0.0028 inch (0.07mm). If the deviation exceeds the maximum, replace the axle hub.
    2. Install the disc and caliper. Tighten to 65 ft. lbs. (88 Nm).
  8. Remove the cotter pin and install the wheel. Lower the vehicle to the ground.
  9. Remove the lock nut cap. While depressing the brake pedal, remove the center axle nut.
  10. Raise and support the vehicle again and remove the wheel, caliper and disc.
  11. Loosen the 2 nuts on the lower side of the shock absorber. Do not remove the 2 nuts and bolts.
  12. Remove the cotter pin and nut from the tie rod end.
  13. Remove the tie rod end from the knuckle using a joint separator or equivalent.
  14. Remove the bolt and 2 nuts holding the bottom of the ball joint to the control arm and separate the arm from the knuckle.
  15. Remove the 2 nuts from the steering knuckle. Place a protective cover or shield over the CV boot on the driveshaft.
  16. Using a plastic mallet, tap the driveshaft free of the hub assembly.
  17. Remove the bolts and remove the axle hub assembly.
    1. Clamp the knuckle in a vise with protected jaws.
    2. Remove the dust deflector. Loosen the nut holding the ball joint to the knuckle. Use a ball joint separator tool or equivalent to loosen and remove the joint
    3. Use a slide hammer/extractor to remove the outer oil seal.
    4. Remove the snapring.
    5. Using a hub puller and pilot tools or equivalents, pull the axle hub from the knuckle.
    6. Remove the brake splash shield (3 bolts).
    7. Use a split plate bearing remover, puller pilot and a shop press, remove the inner bearing race from the hub.
    8. Remove the inner oil seal with the same tools used to remove the outer seal.

    To install:
    1. Place the inner race in the bearing. Support the knuckle and use an axle hub remover with a plastic mallet to drive out the bearing.
    2. Clean and inspect all parts but do not wash or clean the wheel bearing; it cannot be repacked. If the bearing is damaged or noisy, it must be replaced.
    3. Press a new bearing race into the steering knuckle using a bearing driver of the correct size.
    4. Place a new bearing inner race on the hub bearing.
    5. Insert the side lip of a new oil seal into the seal installer and drive the oil seal into the steering knuckle.
    6. Apply multi-purpose grease to the oil seal lip.
    7. Apply sealer to the brake splash shield and install the shield.
    8. Use a hub installer to press the hub into the steering knuckle.
    9. Install a new snapring into the hub.
    10. Using a seal installer of the correct size, install a new outer oil seal into the steering knuckle.
    11. Apply multi-purpose grease to the seal surfaces which will contact the driveshaft.
    12. Support the knuckle and drive in a new dust deflector.
    13. Install the ball joint into the knuckle and tighten the nut to 105 ft. lbs. (142). Install NEW cotter pin.
    14. Temporarily install the hub assembly to the lower control arm and fit the driveaxle into the hub.
    15. Install the knuckle to strut bolts, then attach the tie rod end to the knuckle.
    16. Tighten the strut bracket nuts to 203 ft. lbs. (275 Nm) and tighten the tie rod end nut to 36 ft. lbs. (49 Nm). Install the NEW cotter pin.
    17. Connect the ball joint to the lower control arm and tighten the nuts to 105 ft. lbs. (142 Nm).
    18. Install the brake disc.
    19. Attach the brake caliper to the knuckle and tighten the bolts to 65 ft. lbs. (88 Nm).
    20. Install the center nut and washer on the drive axle.
    21. Install the ABS speed sensor if so equipped. Install the wheel
    22. Lower the car to the ground.
    23. Tighten the wheel nuts to 76 ft. lbs. (103 Nm). Tighten the hub nut while depressing the brake pedal to 137 ft. lbs. (186 Nm) on 1988-91 models and 152 ft. lbs. (206 Nm) on 1992-97 models. Install the cap and cotter pin.
    24. Remove the protective cover from the CV boot. Check front wheel alignment

Posted on Apr 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the panel from below the steering wheel of a 2006 Milan so that I can access easier to remove and replace the malfunctioning brake switch


Just look at it. There could be a few screws to remove or plastic plugs. Some remove by pushing a tab. all are at the front of the panel. Front meaning the furthest from the firewall.

Jan 08, 2017 | 2006 Mercury Milan

1 Answer

Where is the fuel filter on a 2007 mercury milan. And how min are there?


This car has one inline fuel filter, it is located under the car at the right rear, if you lay in front of right rear tire (passenger side) and look under the vehicle you might see it. You need a special tool to release the line. Any auto parts store will have the tools needed.


26229107-tzeeu2zpro05qaxsdkdfurfl-1-0.jpg

Jul 01, 2016 | 2007 Mercury Milan

1 Answer

How to clear vacuum hose on 2007 milan?


if you know there is suppose to be vac.pull it off aand feel with your finger you can feel it.mechanics wire, carb cleaner with red supplied tube,maybe easier to splice new peice in.

Aug 25, 2014 | 2007 Mercury Milan V6 AWD Sedan

1 Answer

How do you change a headlight on my milan?


After studying one for some time and almost giving up I finally checked the owner's manual. It pointed out that there is a bulb access door under the front passenger-side wheel well. I found it, removed the screw and the bulb access door, and was able with some nimble finger work to replace the bulb. It was really neat the way they designed it. But it almost made me take the car to a dealership for what turned out to be a fairly easy repair. When in doubt, read the instructions!

Feb 24, 2011 | 2007 Mercury Milan V6 AWD Sedan

1 Answer

2007 mercury milan factory remote start?


I did the same thing twice, But i can't get it to start again. What gives?

May 12, 2010 | 2007 Mercury Milan V6 AWD Sedan

1 Answer

2007 mercury milan factory remote start?


I did the same thing twice, Yet i cannot figure out how it works. What gives?

Mar 19, 2010 | 2007 Mercury Milan V6 AWD Sedan

1 Answer

Have a 2007 mercury milan and the blower does not work i checked the fuses under the hood and one was burned out i replaced just to have it burn out again


Try disconnecting the wires to the blower motor before you put in another fuse. If the new fuse does not blow you need to replace the blower motor.

Nov 05, 2009 | 2007 Mercury Milan V6 AWD Sedan

1 Answer

2007 mercury milan V6 Car wont start. Jumped it


Remove the lugs at the battery. Clean the posts and the lugs - then reconnect. Your battery won't charge (and the jumpers won't work) largely because of a film on the + post and lug. If you live in a hot summer area, (Arizona) the problem is especially troublesome.

Jul 15, 2009 | 2007 Mercury Milan V6 AWD Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

956 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...