Question about Buick Cars & Trucks

Open Question

Rocker arm torque adjustments 2000 buick park ave

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 312 Answers

SOURCE: torque spec for rocker arm

25 ft lbs

Posted on Oct 20, 2010

sawdust46694
  • 398 Answers

SOURCE: How do you replace the serpentine belt on a 2000

there is a pic under the hood that showes the corect way to run the belt. over and under diferant pulleys. figure out the corect way it goes and use a breaker bar to pull the tenchenor so you can slide the belt on, then let go slow and your done. the soring holds the pulley at the exact right tension. you can do this it's not that hard... good luck
saw

Posted on Jul 09, 2009

  • 98 Answers

SOURCE: how do i install serpentine belt on a 1998 buick

  1. there should be a place on the tenshoner pully to put a ratchet and tale tenshon off the pully then follow the routing diagram for the belt on the radiator suport pannel on the front of the car

Posted on Mar 09, 2010

Testimonial: "Thanks for taking time to answer my ?, but I'm wondering do I have to remove pessenger side motor mount to install serpentine?"

L Holland
  • 70 Answers

SOURCE: how to replace a fuel pump

It's not easy but heres a guide Hope it can help you.


http://autorepair.about.com/od/fixityourself/ss/fuel_pump_repl.htm

Posted on Jun 30, 2010

  • 1 Answer

SOURCE: 1998 Park Avenue: where is the fuse box on a 1998 buick park ave?...

i have a 98 buick park avenue
i got a problem running it. it start but when i hit the break pedal some light comes out the direction signal and it shuts off i check all the fuse

Posted on Aug 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need torque on 1997 chevy tahoe 5.7 rocker arm torque


The rocker arms need to be adjusted, they are not set to a specific torque, they use self locking "crimp" nuts to hold the adjustment, these nuts should not be used over to hold the adjustment replace them.. With the lifters fully "pumped" up tighten the rocker arms to "zero" lash, the turn them in an additional 3/4 turn, you are done.

Feb 21, 2017 | Cars & Trucks

1 Answer

What is the correct torque specs. for lower intake manifold and upper, and rocker arm torque for 02 Buick Rendezvous 3.4 v-6 are the rocker arms pre load non adjustable


Call any major autoparts store for the correct answer. There are updated torque specs for the gm 3.4 vs in order to deal with a common issue of leaking intake manifold gaskets. They should have the correct updated spec for you vehicle based on the specific Vin number

Feb 01, 2017 | 2002 Buick Rendezvous

1 Answer

What is the right way to torque the rocker arms an the sequence


No torque sequence on rocker arm bolts. 11 ft lbs plus 30 degrees.
A torque wrench rated for inch lbs should be a finer adjustment.

Oct 06, 2016 | 2002 Buick Rendezvous

1 Answer

Bought 2000 buick park ave. ultra & do not know how to adj drivers seat up or down.


should have buttons on your armrest or down on the side of the seat by the drivers door if not check in front of the seat

Nov 24, 2013 | 1993 Buick Park Avenue

1 Answer

I have an 1987 Buick Park ave that will not start... I have replaced the fuel filter, fuel pump and even the computer. It does not seem to get any fire. I have checked all fuses. Please help.


POSSIBLE BAD CRANK SHAFT SENSOR OR COIL. YOU SHUOLD ALSO CHECK THE TIMING CHAIN. THE EASIEST WAY TO DO THAT IS TAKE OFF OIL CAP AND HAVE SOMEONE CRANK IT OVER YOU SHOULD BE ABLE TO SEE THE ROCKER ARMS MOVE

Sep 27, 2012 | Buick Park Avenue Cars & Trucks

1 Answer

How do I adjust the valves on a 1998 old bravada 4.3 vortec


You don't. They are non-adjustable hydraulic lifters. GM's spec for torque on the rocker arm nuts: Tighten the valve rocker arm ball studs to 47 N·m (35 lb ft). Once the valve rocker arm nuts are installed and properly torqued, no additional valve lash adjustment is required.

Aug 05, 2011 | Oldsmobile Bravada Cars & Trucks

1 Answer

Dtc po321 on a 94 buick park ave runs good check engine light comes on at 2nd start up i replaced;crank sensor cam sensor and modlue


po321 inthe code for the knock sensor error.look for any unusual knock type sounds, such as , noisy rocker arm, harmonic balanced rubber getting loose, or detonation from low octain fuel, or egr malfunction. check to be sure sensor wiring is ok, or that it's not unplugged.knock sensor is there to detect detonation (spark knock) so pcm can ****** timing.

Dec 18, 2010 | 1994 Buick Park Avenue

1 Answer

How do you adjust valves on a 3.1 buick century


valves are not adjustable torque rocker arms to 120 inch/lb then 30 degrees

May 10, 2010 | 2002 Buick Century

1 Answer

Power door lock switch replacement





Remove or Disconnect

Door handle trim plate.
  1. .Install or Connect

  2. Electrical connector and door lock cable.
  3. Trim panel by engaging hooks on backside of panel.
  4. Push pin fastener in defroster duct.
  5. Screw from behind lamp assembly.
  6. Courtesy lamp assembly.
  7. Two screws in arm rest.
  8. Arm rest cover plate.
  9. Door handle trim plate.
There May Be A Need to Drill Out RIVETS that Hold Motor in place,. Just Replace with>>MACHINED SCREWS & BOLT'S




Remove or Disconnect

  1. Trim panel. See: Doors, Hood and Trunk\Doors
  2. Four tabs retaining switch.
  3. Electrical connector.
Install or Connect

  1. Electrical connector.
  2. Snap switch into trim panel.
  3. Trim panel.

Mar 14, 2009 | 2000 Buick Park Avenue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...