Question about Hyundai Elantra

Open Question

I need a ecm pinout connection for hyundai elantra.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ghost4548
  • 776 Answers

SOURCE: wiring automatic transaxle Elantra 1997

Web site http://www.hmaservice.com/ - register and you'll have access to more info than you can imagine. Crea me.

Posted on May 27, 2009

  • 121 Answers

SOURCE: no crank

first, has the timing belt been replaced? breaks after 60,000 miles and engine locks up.will not crank. .need to take a 22 millimeter socket and see if the engine will turn over by hand. if not remove the timing cover and inspect the timing belt for missing teeth or belt broken.if ther is the cylinder head will have to be removed and the valves replaced.next if there is no communication to the ecm i would check the ecm fuses under the hood and dash use a volt meter and replace the blown fuse.if the fuses and voltage readings are ok you need to remove the computer and test for correct power voltage and for good grounds to the ecm.if ok possible ecm is defective.hope this helps.

Posted on Dec 06, 2009

ZJLimited
  • 17970 Answers

SOURCE: need fil for error code P2626 Hyundai Elantra GLS

P2626 O2 Sensor Pumping Current Trim Circuit/Open (Bank 1 Sensor 1)

I'll sure this has to do with a faulty O2 sensor. This sensor is usually located around the header of your car, or down more on your exhaust.

Try disconnecting your battery for 30 mins, hook it back up, and start your car again. This will erase the error. See if it comes in again.

Hope this help (remember rated this post).

Posted on Mar 25, 2010

  • 7353 Answers

SOURCE: '07 Hyundai Elantra Oil Filter Location

Front of the engine, passengers side. If you have to ask, maybe you shouldnt be trying to do your own oil change.

Posted on May 12, 2010

emissionwiz
  • 75197 Answers

SOURCE: looking for pinout ECM for Dodge RAM 3500 ENGINE CUMMINS 6BT

Fixya has no wiring diagrams due to copyrighting

Posted on Jul 23, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the pinout for this radio that was in a Hyundai Santa Fe 2005?


Do you need Wiring Diagram for hyundai santa fe.Or you need where the radio fits in hyundai santa.The connector of radio.
Please Check the link mentioned below it has all wiring diagram for hyundai santa fe radio.Also it has details for how to connect radio connector.
http://www.allcarhelp.com/2016/05/hyundai-santa-fe-radio-wiring-diagram.html

If you need anything else,please reply.
Thanks.

May 11, 2016 | Hyundai Cars & Trucks

1 Answer

All the service lights are lit up on my 2008 hyundai elantra widows radio breaks and power steering aren't working


use a scan tool to reset the ECM first as the CPU program in the ECM may be corrupted from the battery change

Jan 27, 2016 | 2008 Hyundai Elantra

1 Answer

My 2001 Hyundai Elantra is dying alot the engine light codes are p0720, p0105, p0445


code P105 is manifold absolute pressure barometric pressure circuit. code P0445 evaporative emission system purge control valve circuit shorted. code PO720 AT output speed sensor circuit open or short ground.HAVE MANY CODES COULD BE ECM FAILING HAVE DEALERSHIP CHECK OUT ECM.ECM COULD HAVE SHORT OUT PC BOARD.

Mar 12, 2013 | 2001 Hyundai Elantra

1 Answer

Code p2237on 2004 elantra


CODE P2237 HO2S 11 PUMPING CURRENT CONTROL CIRCUIT OPEN BANK 1 SENSOR 1 POSSIBLE CAUSES. POOR CONNECTION OR DAMAGED HARNESS, OPEN IN HO2S CONTROL CIRCUIT, FAULTY HO2S,THE ECM HAS FAILED.

Feb 21, 2011 | 2004 Hyundai Elantra

2 Answers

Where is the fuel pump relay on a 2000 Hyundai Elantra?


Look under the dash on the left side. You'll see the ECM (computer) under there. Right above the ECM, in fact hooked to it, is a plastic module that will have about 4 relays in it. From Right to Left there should be one relay with an extra opening above it, then a single relay (this is the Fuel Pump Relay), then a slot with 2 emptys and then a large relay on the Le

Oct 21, 2010 | 2000 Hyundai Elantra

1 Answer

99 elantra alt not charging battery' installed new alt and battery and fuse good and still no charge on battery


check 10 amp ECM fuse. Your alternator voltage is regulated by the ECM. If the fuse is good, consider replacing the ECM.

b4f4aeb.gif

Oct 05, 2010 | Hyundai Motor 1999 Elantra

2 Answers

No crank


Sounds like you need new brushes put in the starter,Worn out brushes set no code,does the starter solenoid just click or is it the relay you're hearing?

Dec 06, 2009 | 2001 Hyundai Elantra

2 Answers

My 2001 hyundai elantra (automatic) loss power while driving


The check engine light usually comes on when there is a faulty sensor. or circuit. Sounds like you may have a faulty throttle position sensor. It would be best to have engine codes read to pinpoint exact problem area. Many part stores do this for free.

Sep 25, 2009 | Hyundai Motor 2003 Elantra

1 Answer

Elantra automatic trans problems


Does the Check Engine light come ON when this happens? Whenever the "Check Engine" light comes on, there is always a DTC (Diagnostic Trouble Code) stored in the ECM (Engine Control Module). You'll need an OBDII (On-Board-Diagnostics) scanner to retrieve any codes recorded/set in ECM. Once you do this and let us know what, if any codes are set, then we can go from there.

Jun 28, 2009 | 1998 Hyundai Elantra

1 Answer

My Hyunday Elantra' 94 won't start when hot


uncap and press valve on fuel rsail to purge and confirm fuel. Then ck the first sensor in duct coming out of air cleaner. unplug and plug it back in ensuring good connection. good luck

May 30, 2009 | 2001 Hyundai Elantra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...