Question about Cars & Trucks

1 Answer

I have a 2006 ford fusion and currently my heat and air hardly blow out even when its turned on high and my heated seats flash twice and doesn't stay on

Posted by on

1 Answer

Check voltage if alternator is put out 14 volts

Posted on Oct 18, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: rear heat in 2004 gmc

I have a 2006 yukon and have had to replace the actuator in the rear heat/ac twice.  It moves a valve that closes the cold/hot ducts.  It is a cheap defective part/design.

Posted on Nov 07, 2008

  • 2 Answers

SOURCE: my 1995 ford areostar van when heat is on only blows cold air

The aerostar has a vacuum operated watervalve in the heater tubing.the valve is located on the
passenger side inner fender behind the aircleaner.with someone operating the controls inside the van
you can check to see if you get vaccum by removing the tiny hose that goes to the water valve
and checking for suction as you in the van person operates the heater conthttp://www.fixya.com/PostAnswer.aspx?thid=1323651&prdid=696348rols. If you have no
vaccum there is a break in the hose between the intake manifold and the valve. If you do get
vaccum check to see if the valve changes position from vaccum on to vaccum off. you can see
this motion on the small lever on the side of the valve. If the valve lever doesn't move you can
move it manually to allow the water to flow through the heater core. if the valve won't move manually
there is an obstruction in the valve. If it does move manually the vaccum diaphragm is gone.
replace the valve. if it moves to the manual open position you can hold it open with a tywrap.
before you get to this point you should first check to see that there is enough coolant in the
radiator. If you still have no heat you can check the coolant flow through the heater core. to do
this remove both heater hoses from the valve and pump water from a hose into one of the hoses
water should flow from the other hose. If it doesn't the heater core is blocked. The rear heater
operates the same way with the watervalve under the van just behind the drivers seat.
Good luck.

Posted on Dec 31, 2008

  • 1 Answer

SOURCE: 03 chevy tahoe

There are seperate blowers for the front and rear air. It is most likely either your blower motor or the resistor, both located under the passenger side dash. I got a blower from a salvage yard for $25, But ended up having to get the resister from the dealership for about $130. Hope this helps.

Posted on Jan 20, 2009

  • 7 Answers

SOURCE: Ford Windstar SE, 3.8L V6, 1999, front seat heat/defrost is cold

the blendor actuators strip out the gear inside the actuator cases on these all the time. replace the actuator.

Posted on Mar 19, 2009

  • 1 Answer

SOURCE: Heated seat

It is the heatling element, stock elements have a single wire snaked through the element and when the circuit breaks it is done, aftermarket elements have a wired grid that if one area fails it still works, they also spread a more even heat.

Posted on Oct 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater won't work after changing battery


Check your coolant level. The changing of the battery may not have anything to do with the heater not blowing hot air (I assume that is the problem? air blows but no heat?).

Dec 27, 2013 | 2006 Ford Fusion

1 Answer

Changed thermostat in 2006 ford fusion now have no heat


did you put right.did you bleed, air lock,coolant.

Mar 02, 2013 | 2006 Ford Fusion 2.3

1 Answer

2007 ford fusion, heater blows cold air most the time


its probably low antifreeze. or your heating core is going out or your thermostat is sticking and may need to be replaced

Jan 16, 2013 | Cars & Trucks

2 Answers

2006 Ford Fusion Air Conditioning compressure not turning on.


Thats pretty high if the system is not running. Average pressure on the low and high side should be near outside air temp.
Normal low side is 30-40 psi and high side is 200-250 psi when the system is running and the freon charge is full.

Aug 28, 2012 | 2006 Ford Fusion

1 Answer

Lack of power, hesitation, climate control blowing hot air


Always check body grounds. You may have good power to the engine with a good ground still, but your body grounds control power to all else.

May 03, 2017 | 2006 Lincoln Mark LT

1 Answer

My heated seat in my 2006 ford fusion won't turn on when engine is started it lights up and goes off. it lights up only right after starting


You really need a scanner to diagnose, along
with the service manual
Most likely a bad under seat blower assy.
Do you hear it running? Listen to the other side

Jan 27, 2011 | 2006 Ford Fusion

1 Answer

Driver side seat heater light comes on and goes right out seat wont heat up passenger side works fine


The problem lies in the drivers side seat, the heating element for the back of the seat or the seat heating element has an open or shorted circuit. the part from ford will run you about $150.00 dollars.

Dec 09, 2010 | 2006 Ford Fusion

1 Answer

2006 tahoe with heated seats. when the seat is


The heating element in the seat may be failing, even thogh it heats the seat, the element could be causing the circut to spike upon power shut down. Relay takes mili-second to shut down after ignition kill and power feed comes direct from battery. Check amp. draw at switch of bad seat and good seat upon shut down. If bad seat higher that 5 amp difference element n/g. Also check for bad relay as they can short internal and cause problems if primary power cut before switch shut down.

Jan 30, 2010 | 2003 GMC Sierra 1500

1 Answer

Rear heat in 2004 gmc yukon blows only cold air when turned to heat. driver heated seat button lights up for only a few seconds and turns off.


I have a 2006 yukon and have had to replace the actuator in the rear heat/ac twice.  It moves a valve that closes the cold/hot ducts.  It is a cheap defective part/design.

Nov 07, 2008 | GMC Yukon Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...