Question about Dodge Dakota

Open Question

1995 Dakota 3.9 engine frame mounts same as 5.2

Posted by Anonymous on

2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 1796 Answers

SOURCE: So I have the 1995

To remove the left motor mount place a jack under engine just as you done it before, unbolt the mount assembly from the frame, remove the engine mount through bolts attaching the rubber insulator to the frame brackets, jack up the motor and remove the rubber insulator, then remove the engine mount brackets from frame and engine To install back, attach the engine mount frame brackets to the mounts. Tighten the nuts just enough to hold them securely, Lower the engine slowly onto the supports. Tighten the engine support nuts to 74 ft. lbs. (100 Nm). Tighten the bracket bolts to 70 ft. lbs. (95 Nm).

Good Luck! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Posted on Jan 08, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers


Inside the engine compartment should be a black fuse box with the location of everything inside the lid.

Feb 22, 2011 | 1995 Dodge Dakota

1 Answer

I am stupid when it comes to cars, just to warn you. i need to know exactly how to get to my crank sensor on a 1991 3.9L Dodge Dakota 2wd auto.

V6 and V8 engines
See Figure 3
  1. Remove the air cleaner assembly.
  2. Unplug the wire from the sensor.

0900c15280070e13.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Crankshaft position sensor location-V6 and V8 engines

  1. Unbolt then remove the sensor from the engine.

To install:
  1. Position the sensor to the engine, then install the mounting bolts, tightening them to 70 inch lbs. (8 Nm).
  2. Install the air cleaner assembly.

***This can be viewed at become a member and look up repair guide for crankshaft postion sensor. *** be sure mounting surface is clean before installation.

Jan 03, 2011 | 1995 Dodge Dakota

1 Answer

Can't find a motor mount

Your engine sets on motor mounts and then the motor mounts set on the frame. There are also some motor mounts in the front of the car that attach to the frame with a rubber housing and big bolts running through them. Usually in the middle of the engine.

Dec 14, 2010 | 1995 Saturn Sc

1 Answer

How do i change a moter mount

You have to have a way of razing the engine weather its jacking or an engine lift from up top. Support the engine then unbolt the mount from the engine raise the engine unbolt from frame then pull the motor mount out. Put the new one in reverse of taking out. Take ex stream caution use jack stands and a backup engine support. Safety first.

Nov 24, 2010 | 1996 Dodge Dakota

1 Answer

Where is oil filter located for a 1995 dodge dakota 4x4 v6

its around the engine mount L/S or R/S some have it on V6 left but you have a 4X4 and due to that is changees or there tuckd in higher. let me if this help.

Aug 01, 2010 | 1995 Dodge Dakota

1 Answer

Wheres the fuel pump located

It is usually mounted in 1 of 3 places, on the drivers side of the engine block and operated by the cam, inside the fuel tank, which usually requires removal of the fuel tank or mounted on the frame, however this is usually not that common. If you still can't find it, I suggest tracing the fuel lines down from the motor and they will lead to the pump itself. Hope this helps?

Jan 03, 2010 | 1988 Dodge Dakota

1 Answer

I have a 93 dodge dakota,i'm trying to find the ground strap.

on some it goes from motor to firewall or motor to the frame.. you have to have a good eye for it is easily overlooked...good luck

Nov 17, 2009 | 1993 Dodge Dakota

2 Answers

Where is fuel filter on 1995 Dodge Dakota

That because it is located in the fuel tank built into the fuel pump:]

Jun 21, 2009 | 1999 Dodge Dakota

1 Answer

1995 Taurus motor mounts

these are known as cradle bushings. the frame around engine is called the cradle. you can get mounts from ford should just replace these and be fine

Oct 16, 2008 | 1995 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides