Question about Cars & Trucks

Open Question

Engine removal ford transit 2001 model

Is it easier to pull the motor out of a ford transit through the top or the bottom

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75005 Answers

SOURCE: engine removal on 2002 ford taurus se

the engine comes out the bottom, u have to remove the entire sub frame.

Posted on May 07, 2009

c17hydro
  • 2984 Answers

SOURCE: need to replace "check engine" lamp in dash of 2001 Ford Explorer

The easiest way is to actually remove the instrument cluster. You would have to have teenie tiny hands to get to the bad bulb from underneath/behind/and up to the bulb.

It is really not that difficult to remove the dash. If you go to your library you can take a look at a Chilton's or Haynes manual...or better yet, just invest in one from a parts store and it will tell you how to do it step by step.

Posted on Mar 13, 2009

  • 1118 Answers

SOURCE: knocking in the bottom of ford 5.4 liter engine

If you hear it knocking no bearing replacement is going to fix that long term. Its best to pull it, the crank shaft will have to be turned or polished and or replaced, weather its a rod or a maine, and posibly line boared if its a maine thats knocking. Do it right and pull it.

Posted on Apr 10, 2009

  • 13 Answers

SOURCE: trying to remove engine from 2001 sebring sedan

comes out through the bottom with the tranny att. if you cannot get the car high enough, take off the compleate front clip and slide it out the front, and yess lots of screws will snap and break. there is 2 or more hidden bolts on the cross member just be patient and have lots of kitty litter... lol

Posted on Dec 03, 2009

Testimonial: "excellent thanks"

jasonburchel
  • 24 Answers

SOURCE: ford transit starter motor removal

disconnect battery earth leadlocate starter motor (by gearbox and engine)start undoing boltspull out starter motorreverse the steps to put back in

Posted on Jul 08, 2012

Testimonial: "Good thinking about following lead.I shall go and try that method "

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove engine 2004 ford freestar 3.9


Pull it from the bottom it's way easier drop the cradle and lift the van up and over the engine

Aug 21, 2014 | 2004 Ford Freestar

2 Answers

I have a 2001 cadilac deville that has a wicked knock in the engine. it is a rod knock (from the sound) so i figure my options are to change the engine, or change the rod ect. I wanna know if the engine...


Thats going to be a tricky pull. you can actually do BOTH methods fro pulling that motor. Which ever is easier for you would be better.

As far as the rod knock. Rod knock simply means that the rod bearing has spun and is no longer a smooth surface. potentially, you could pull the motor and replace just that rod and bearing if the crankshaft was unaffected. the majority of the time, more work needs to be done. I think in this case, it may be cheaper to remove the motor and replace the crank and bearings. A replacement used motor will probably run about 1k if you can find one at a yard.

Apr 07, 2014 | 2001 Cadillac DeVille

1 Answer

2001 ford ranger oil pan gasket removal?


Remove the engine mount pin and carefully raise the engine yup as far as possible, be sure to use a large block of soft wood like pin under the pan so you won't damage it. Remove all the pan bolts, You do not have to remove the oil pan completely. With the pan lowered, remove the old gasket completely and take the new gasket and pull it around the bottom of the pan an pull it up to the engine. Basically wrap it around the oil pan. It you have the gasket that is plastic with rubber seal inserted in it, it is easier. It has clips that hold it to the pan and stays in place when lifting the pan back to the engine. Also add silicone in the corners on the front and rear bearing caps.

Jul 02, 2012 | Ford Ranger Cars & Trucks

1 Answer

Which way do u pull a engine out of a 99 winstar van from the top or bottom of the vab


after disconnecting tranny and all other things. it is much easier to remove engine from top.

May 10, 2011 | 1999 Ford Windstar

1 Answer

Removing engine mounts to pull engine only


Most mounts have a big bolt through the middle of the the 2 halfs, top and bottom, to make it easier to pull the motor. Just pull the one bolt, and it should be free. Hope this helps.

May 19, 2010 | 1999 Dodge Durango

1 Answer

How to take the engine out?


I have done this a ton a two post lift is a definite helper in this situation as you will most likely have to pull it from the bottom unless you disassemble most of engine to pull from top anyways if you pull from the bottom it is easier to keep engine and trans together remove exhaust and unplug everything that attaches to car remove drive shafts be careful when removing them dont beat on the threaded end you wont be able to get nut back on. support engine and trans and remove driverside mount that goes to trans it is located around or under the battery tray and then remove the passenger side mount you will need to unbolt the three bolts that bolt it to the car and the one big nut that holds to engine. then drop out or set on ground and lift car. remember radiator hoses,intake,fuel lines,battery,starter cables,etc. need to be removed pretty easy once it pretty much done hope this helps you can email me direct Russ899@msn.com for help I also take it that this is a SOHC engine?

Apr 30, 2010 | 2001 Ford Focus

1 Answer

On the 2000 and 2001 acura tl is it easier to pull the engine from the top of the car or the bottom?


i would say from the bottom. there might be more work invoved but i believe removal and installation would go easier. but if you feel there's enough room to get the engine past the trans , go for the top

Mar 09, 2010 | 2001 Acura 3.2TL

1 Answer

2001 F-150 HOW TO REPLACE AC BLOWER


on the pass side in the engine compartment on the fire wall you will see an electric motor. unplug the wire connecter and detactch the rubber tube from the main box.then remove the three retaining screws and pull out the motor and fan assembly,if it has cruise control you might find it easier to also remove the acuater from the fender.this is held in place by two 10 mm bolts.just lay it off to the side to give yourself more room

Sep 27, 2009 | 2001 Ford F150 Styleside SuperCrew

1 Answer

I am changing a motor in 2001 intrepid is it easier to pull the transmission with it or should i separate the engine and leave the tranny there


IT IS EASIER TO SEPERATE ENGINE FROM TRANS AND REMOVE IT FROM VEHICLE..REMOVE UPPER RAD SUPPORT AND RAD FANS..REMOVE WIPER ARMS/COWL TRIMAND LINKAGE/CROSS BAR AND WILL OPEN IT UP QUITE WELL TO WORK ON

Aug 29, 2009 | 2001 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...