Question about Saturn SL

Open Question

Neutral safety switch saturn

How to test or temporily bypass

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75797 Answers

SOURCE: Neutral Safety Switch Location

on the transmission where the shift cable attaches.

Posted on Jun 15, 2009

  • 1129 Answers

SOURCE: neutral safety switch

It is located on the side of the transmission, follow the shift cable down to it you will recognize it because it has a electrical wire comming off it and either a shift lever or shift cable going to it.

Posted on Jul 14, 2009

  • 523 Answers

SOURCE: replace neutral safety switch on a 1988 gmc sierra

Typically the Neutral Safety Switches are located with the gear selector, either in the column or the floor.

Hope this helps,
Tom

Posted on Aug 21, 2009

dncholas
  • 222 Answers

SOURCE: neutral safety switch '97 eclipse

Under dash driver side look behind the upper arm of clutch pedal and you should see a green and black wire coming from the button (switch) assembly on the firewall. The wires go up above the clutch pedal. About in the middle of under dash on the left side you should see a white connector these wires run to. Disconnect. I just had the problem and not only starts now but not stalling like it was but it's only been one day but tested it pretty good.

Posted on Aug 16, 2010

dttech
  • 4803 Answers

SOURCE: what wires do I need

The wires on the Transmission Range Sensor that control the ability to crank the starter are the BLACK/GREEN wire at Pin 6 and the wire at Pin 10 which is either BLACK/GREEN or BLACK WHITE depending on your model. (build - date and transmission type)

With all that said, I think it only fair to warn you that bypassing these wires will set codes in your Engine Control Module. It is not going to like it if there is power at pin 10 with the transmission in reverse or any of the forward gears. This may also cause your transmission to not shift properly because the ECM will not know for sure what gear you are in.

Posted on May 10, 2011

Testimonial: "thanks so much for the information I will install a switch and only use it when needed and to ensure that this is my problem."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What are the wire colors of the neutral safety switch on a 2000 Caravan 3.0 liter with a 4-speed automatic transmission.


Brown wire with yellow tracer shows to be wire color. You can always jump the starter to get it to crank, but, that doesn't mean it will start. In the past I have been lucky, different vehicle, I put the key in on position, jumped the starter relay, the vehicle started, I managed to get it home.
When testing, make sure tranny is in park or neutral and functional parking brake is set. There are safety issues, safety is your responsibility. You don't want the vehicle to move when your working on it.
You realize if you bypass anything, it may start in any gear, if it does it will run over you or one of the kids, anything that gets in the way. Again, safety for everybody is your responsibility.

May 09, 2016 | Cars & Trucks

1 Answer

I have a 00 dodge stratus 2.5 how will bypass the antitheft circuit in order to start


Bypassing Neutral Safety Switch, Chrysler sebring 2000 ...

? 2:21
https://www.youtube.com/watch?v=uBszX3CnXeo
Apr 27, 2012 - Uploaded by Brianna Kufa
Bypassing Neutral Safety Switch, Chrysler sebring 2000. Brianna Kufa ... 1) Remove wiring harness attached to tranny. (there's 4 connections: ...

Part 1 -How to Troubleshoot a No Start (Chrysler 2.0L, 2.4L)

troubleshootmyvehicle.com > Chrysler > 2.0L, 2.4L
Dec 29, 2012 - Failed starter motor. Failed neutral safety switch. ... Dodge Vehicles: Avenger. 1995 ... Stratus. 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002.

Automatic Shutdown Relay - Allpar



Nov 13, 2015 | Dodge Cars & Trucks

1 Answer

I am running a 2000 good Taurus in a demo derby can i bypass the neutral safety switch and if yes how?


How to Bypass neutral safety switch - YouTube

? 2:15
www.youtube.com/watch?v=poLZ7od9vCM
Apr 7, 2014 - Uploaded by Fix Your Car Videos How to Bypass neutral safety switch is easy. ... I get the part where you hook up a positive wire to the push button but where.... Neutral Safety Switch Replacement 98 Silverado (full size GM trucks) ... Bypassing Neutral Safety Switch, Chrysler sebring 2000 - Duration: 2:21. by Brianna Kufa 36,694 views.

Sep 15, 2015 | Cars & Trucks

1 Answer

How to bypass the neutral safety switch on a 2000 Chevy Silverado Z 71 4 x 4


The purple wire with a white stripe goes to the starter from the neutral safety switch. I believe it is the yellow wire at the neutral safety switch that will have the the signal from the ignition switch for the start signal. ( Test this yellow wire with a test light while holding the key in the start position to see if it lights to make sure yellow is the correct color ) and join the wires together. This will by-pass the neutral safety switch

Aug 22, 2015 | Cars & Trucks

1 Answer

I gotr a 98- 4L60E trans in limp mode & want to bypass neutral saftey switch. Can you help?


Bypassing the neutral safety switch won't help with the transmission problem. That switch is only wired into the start circuit.
Scan the computer for trouble codes. Has to be a code if it is in limp-in mode.

Nov 20, 2013 | 1994 Nissan Pathfinder

1 Answer

The clutch safety switch behind peddle seems to need replacement.


of course!...however you do not want to bypass this safety switch! bypassing it will allow a car in gear to start...possibly running over and/or killing someone! get a cheap switch at a salvage yard!

Feb 09, 2013 | 1997 Saturn SL

2 Answers

I have a chevy 305 with an older transmission with no neutral safety. The starter that i have has 3 prongs the only way to have the system work is to short the starter and it will start the engine is there...


The neutral safety switch is on the transmission not the starter. If you suspect it's not working, simply unplug it. Just REMEMBER that the truck will now start in ANY gear not just park or neutral. Hope this helps.

Sep 07, 2010 | Chevrolet 1500 Cars & Trucks

1 Answer

My 2001 porsche boxter S 3.2 will not start in park, but will start normally in neutral, does anyone know why? (it's an automatic)


1.Shifter linkage could be out of adjustment, and not allowing the Neutral safety switch to be bypassed, when in the Park position.

The shift linkage, could move the arm of the neutral safety switch far enough, to bypass it when the shifter is in Neutral, but not far enough when the shifter is in Park.

2.Perhaps the Neutral safety switch is bad, or has come loose on it's mount, and is out of position.

Aug 01, 2009 | 2001 Porsche Boxster

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...