Question about 1992 Dodge Dakota

1 Answer

Speedometer magnetic sensor located top of bellhouseing

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 100 Answers

Crank position sensor otherwise known as engine speed sensor.

Posted on Oct 18, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1998 mercury sable won't start no fire to plugs or fuel any ideas.


make sure when ignition is turned on or when cranking engine that immobiliser is disengaging.also locate crank angle sensor usually mounted in bellhousing to read off flywheel or at crankshaft damper pulling.inspect and clean magnetic side of sensor and connection terminals also possible damage to cable

Dec 24, 2015 | Mercury Cars & Trucks

Tip

Speedometer quits working and D4 light flashes on 1995 Honda Odyssey. The...


Speedometer quits working and D4 light flashes on 1995 Honda Odyssey. The Vehicle Speed Sensor (VSS) is bad. You will need a replacement ($39 online) sensor, Ratchet with extra long extension, 10 mm socket w/ swivel, a long flexible wand with a magnet on the end, and a flashlight. Unplug the wire from the old VSS. Remove the two mounting bolts. Lift out the old VSS and the drive key. Put a small amount of grease on the new drive key and insert it into the new VSS. Plug the wire into the new VSS and use the wire to lower the VSS into place aligning it with the two mounting holes. Use the magnet wand to lower the bolts into the holes and turn to just get the bolts started. VSS IS FLUSH WITH THE TRANSMISSION BEFORE TIGHTENING THE BOLTS. You are now finished. You can access the VSS from the top of the engine in your garage/driveway. It is located on the top/backside of the transmission, just below the air cleaner hose. Best done in the morning when the engine is cold unless you like getting burns on your forearms. Good luck!

on Jan 31, 2009 | 1995 Honda Odyssey

1 Answer

1989 toyota corolla 1.6 gl, where can i find the terminal for speedometer in the engine bay..


Output speed sensor usually located in transmission usually close to where axles go into transmission. The sensor can be identified by having 8 mm headed bolt that hold the sensor in. These speed sensors just don't quit one day. A wire is usually the culprit or debris on magnet of sensor or physically broken sensor. If speedometer intermittently starts working then its always a wire with bad connection.

May 13, 2014 | 1989 Toyota Corolla 1.6

1 Answer

Crankshaft Position (CKP) Sensor LOCATION


Under hood, center, rear engine area, top driver side of transmission bellhousing, mounted in bellhousing

Oct 18, 2011 | 1997 Jeep Grand Cherokee

1 Answer

How to replace crank shaft position sensor


Click over image for zoom...

zjlimited_1122.jpg

Fig. 1: View of the crankshaft position sensor and its location-1996 5.2L engine shown


zjlimited_1123.jpg

Fig. 2: View of the crankshaft position sensor and its location-1996 4.0L engine shown


Removal & Installation
4.0L Engine
  1. The CKP sensor is located on the transmission bellhousing. Disengage the sensor wiring connector and remove the sensor wiring hold-down clip from the fuel rail.
  2. Remove the sensor mounting bolt and carefully pull the sensor out of the bellhousing.
  3. Installation is the reverse of removal.

5.2L and 5.9L Engine
  1. The CKP sensor is bolted to the top of the cylinder block near the rear of the right cylinder head. Disengage the sensor wiring connector and remove the two sensor mounting bolts.
  2. Carefully pull the sensor out of the cylinder block.
  3. Installation is the reverse of removal.

Hope this helps (remember to rate this answer).

Apr 28, 2011 | 1996 Jeep Grand Cherokee

1 Answer

My sports light keep flashing and when i start driving in slows down when it hit second gear...


It is your speedometer sensor that is doing this. Located on the top of bellhousing just to the left as you look down at it.

Feb 14, 2011 | 1991 Honda Accord

2 Answers

Crank sensor location for 2002 durango 5.9


should be on the drivers side back of motor stuck in the tranny bellhousing at the top held in by either a 10mm bolt or a 12 mm

Jan 21, 2010 | 2002 Dodge Durango

1 Answer

Is speedometer connected to Tranny?


There is a vehicle speed sensor on top of the rear differential, this sensor is also for the anti-lock brakes. Sometimes you just remove it and clean it (it's magnetic) and may start working again otherwise you have to buy new. Yes, this sensor will affect the trany shifting.

Nov 07, 2009 | 1999 Ford Explorer

1 Answer

Broken speedometer


Not much info to go on, If your speedometer is not working it is more than likely a speed sensor. On the 96 it is located on the rear differential. It bolts in on the top of the hogs head, and only takes a single 10 mm bolt to hold it in. Before you replace it, take if off and clean it and try it. Sometimes the magnet gets too much wear particles on it to read the pulses. If that does not work , replace it before having to go to the computer or the cluster. 9 ot of 10 times it is just the speed sensor,.

Oct 01, 2009 | 1996 Ford Explorer

2 Answers

Green sports light blinks , speedometer needle bounces or doesn't


Does your D4 blink and is your cruise control operating. When you start it does it sometimes start real rough and shake a lot? If so it's probably your ICM.

May 19, 2009 | 1991 Honda Accord

Not finding what you are looking for?
1992 Dodge Dakota Logo

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7697 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...