Question about 1990 Mitsubishi Minivan

1 Answer

One light wount go the bulb is good it is in a l200 ute four front lights one inside light dont go

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Fuse or badconnectin

Posted on Dec 17, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
leetamara
  • 702 Answers

SOURCE: my reversing lights dont work how do I change the bulb? Its a Mitsubishi L200

Remove the screws that attach the lense to the truck. Twist the bulb hold from the backside and remove the bulb. Installation is the reverse.

Posted on Jun 12, 2008

afarri
  • 1386 Answers

SOURCE: ute has just started squeaking

Hello and welcome to FixYa!

Surely the suspension bushings are worn out and needs replacement. I strongly suggest that you replace the shock absorbers too to lessen the stress on bumps. Tie rod bar and tie rod end replacement will be required to make the car stand right again. This will get rid of uneven tire wear.

Hope this helps and thank you for using FixYa! Have a good one!

Posted on Apr 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota hiace lights wount come on


Check the dimmer switch! Head lights should still work if dimmer! But no interior dash lights! Fuse for lights is under hood in fuse center! If it is the headlights I would check the switch and if applicable the relay! I assume you have checked for ground at the light and power at the headlight fuses!! Good luck

Feb 10, 2015 | Toyota HiAce Cars & Trucks

Tip

Dash lights out Taillights out (Round 1157 bulbs all cars)


Common problem or complaint, Dash lights out or rear running lights not working. Most common problem for this is the round bulb for the brake and running lights flatten out over time and touch each other inside the bulb holder normally the ends should look like nn but when flattened out look like this _ _ and end up touching and shorting out, replace both bulbs. And on GM cars front running lights can cause the same thing so always check all four running light bulbs(Front and Rear). If it has the turn signal and running lights on the same socket always check this first. G.M. had built into it's wiring system a fail safe that if one running light went out the dash lights will not come on, this is so that you don't get a ticket for a running light or brake light out.

on Dec 03, 2009 | Chevrolet C2500 Cars & Trucks

1 Answer

Where does the bulb go for brake light


Front or rear? Often you can get to the light either in front, under the hood near the inside side of the grill. The rear one would be under the trunk lid on the inside. All it should take is a screwdriver, and a new bulb, and some manual labor. Good Luck.

Jul 01, 2012 | 2001 Cadillac DeVille

1 Answer

I have a blown car fuse and when replaced it blows right away


no idea without a good look but i suspect a incorrect type of bulb fitted as some have two contacts and some one and this i think could be the problem as a single pole bulb is fitted into a double pole bulb holder

Jun 09, 2012 | Ford Escort Cars & Trucks

1 Answer

Rear lights dont come on...front works and fuses/bulbs are good. Any ideas?


The bulb check unit, which detects when the rear lights are blown, is malfunctioning or has gone totally bad. It's located inside the trunk mounted, drivers side tail light assembly. Have it checked out and repaired if necessary.

Sep 16, 2011 | 1991 Honda Accord

1 Answer

Blinkers dont work properly


start by looking for a bad ground to one of the light sockets

Jul 23, 2010 | 1997 Oldsmobile Cutlass Supreme

3 Answers

Running lights dont work, fuse is good


replace headlight switch this is very common problem

Jun 29, 2009 | 2003 Ford F350 Super Duty DRW SuperCab

2 Answers

1991 volvo tail lights


Could you take out a bulb and with a testlight/probe check that you do in fact have power to that circuit .Also check that they are the correct bulb for that application I have seen people put indicator bulbs in where therse supposed to be a double filament bulb.Does the base of the bulbs lead contacts line up with the two steel terminals inside the plug?

Oct 20, 2008 | 1991 Volvo 240

1 Answer

My reversing lights dont work how do I change the bulb? Its a Mitsubishi L200


Remove the screws that attach the lense to the truck. Twist the bulb hold from the backside and remove the bulb. Installation is the reverse.

Jun 11, 2008 | 1988 Mitsubishi Pickup

Not finding what you are looking for?
1990 Mitsubishi Minivan Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...