Question about Cars & Trucks
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
if its diesel, attach a tube to pipe leading into primer pump.[black bulb ]. attach a pump . and tube from outlet of pump to container pump out diesel till empty. if petrol locate pipe feed from tank and connect to it same as earlier
Posted on May 26, 2009
SOURCE: peugeot expert 20 hdi
Hi, I have a 2.0HDI Expert which was doing the exact same thing as yours, blowing thick black smoke, sluggish and loss of power on gradients, a hissing sound and surging. I replaced the air flow meter but that didn't help. I was told to replace the turbo but a turbo expoert told me not to as it would blow white smoke if it was faulty. I was then told to replace the injectors but a diagnostic test showed them to be functioning fine. I was then told to look at the intercooler which had thick sludge at the lower left pipe. I replaced it today - Sunday 12th July and it is now driving like a new van. It now pulls me up gradients with ease in 4th and 5th instead of having to drop gear to get to the top. I got a replacement from Euro Car Parts for £147 inc VAT. To tell if this is your problem, look through the gaps in the lower section of the bumper at what looks like the radiator and look for sludge over the inside of the bumper and all over the pipe where it joins the back of the radiator (intercooler). Also open the bonnet and look down behind the grille for the same sludge. Hope this sorts it for you. Barry, Newtownards, Northern Ireland.
Posted on Jul 12, 2009
silly question, however did you check the air box for nests. it is not uncommon for rodents to climb in and make themselves at home. i would also say to get a maf from ford. check ALL around the engine compartment and underneath for evidence of rodents and their leavings. youll be very suprised what you may find.cheers
Posted on Dec 19, 2009
SOURCE: renault megane 2004 - when
it`s the oxygen sensor
thats why the car is mix fuel/air in wrong ratio generating unburned fuel in form of black smoke and check lights on
you got to change that sensor
i hope my answer was helpful and convince sir .
Posted on May 30, 2011
I found an answer that worked for me here. (I have a 2001 Chevy Venture.) http://www.fixya.com/cars/t4093012-code_p1404_dodge_ram_1500_meanIn case links are not allowed, here's the text:That code is the EGR. I'd start by checking for a bad connection on the EGR plug-in. Pull the connector off and inspect each individual terminal inside the plug and the connector pins inside the EGR valve.
I found this solution at another forum on this issue. It worked on my 2001 Grand Am:
"Many GM built cars have a tendency to have the 'Check Engine Soon' light come on as a result of DTC code P1404. P1404 is described as EGR valve pintle stuck open, which in most cases is a false alarm. I had this happen with my '01 Grand Am. A little bit surfing on internet reveals that GM has a solution for the problem, a re-flash for the car's computer.
A software re-flash as a fix kind of indicates that the vehicles with this problem were built with it but I don't think GM will be re-flashing cars outside warranty for free. They will want their $100 for it.
Some hands on people I found had purchased a new EGR valve and changed it but the problem remained.
Possible reason (very likely) for the false P1404 code is that the plastic piston of the EGR valve position instrument (LVDT?) wears over time and starts reading a different position at valve closed than what it was when the EGR valve was first installed.
When the car was built and the computer circuits energized for the first time the computer learned the EGR valve closed position signal from the valve position instrument that is built on top of the valve itself. Over time, when the instrument wears, a slightly different signal is sent to the computer and when it differs enough from the 'Valve Closed Signal', that the computer had learned, the trouble code P1404 is set and the 'Service Engine Soon' light comes on.
Replacing the EGR valve with a new one does not necessarily fix this problem because the 'Valve Closed Signal' between valves is slightly different and it is just pure luck if your new valve would give a 'Valve Closed Signal' close enough to your original valve's signal not to set the trouble code. This is why the new EGR valve 'Valve Closed Signal' must be re-learned by the computer.
So, what this all means is that if the P1404 is a false code meaning that the valve pintle is not stuck open, then new 'Valve Closed Signal' can be re-learned by the computer using the old valve.
For fixing this problem the tool you need to have is a simple OBD II code scanner that can be used to erase trouble codes. There are many scanners of different price range on the market. I purchased one from AutoZone for about $90.
A code scanner is a very handy tool to have and I recommend everybody who is just slightly hands on type of a person to get one. It will end up saving a lot of money over time.
The fix goes like this:
1. Disconnect the wire harness from the EGR valve.
2. Turn key ON and erase the trouble code(s) from the car's computer AND TURN KEY OFF IMMEDIATELY WHEN THE SCANNER SAYS CODES HAVE BEEN ERASED. DO NOT TURN KEY ON BEFORE YOU RE-CONNECT EGR WIRE HARNESS.
3. Re-connect EGR wire harness and your problem should be fixed.
Posted on Dec 01, 2011
Tips for a great answer:
Jul 10, 2015 | Peugeot Cars & Trucks
Feb 15, 2015 | Cars & Trucks
Feb 12, 2011 | Pontiac Sunfire Cars & Trucks
Jun 27, 2010 | 2006 Peugeot 604
Aug 03, 2009 | 2006 Peugeot 604
Jul 19, 2009 | 2006 Peugeot 604
Jul 11, 2008 | 2006 Peugeot 604
198 people viewed this question
Usually answered in minutes!