Question about Chevrolet Chevy

1 Answer

How do you remove an ignition switch on a 2003 Chevy G3500?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,036 Answers

The ignition switch located right side of the steering column. you need to remove steering column covers and drivers knee bolster

Posted on Oct 17, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76630 Answers

SOURCE: remove ignition switch

U must dis-arm the airbag 1st, disconnect the battery for 30 minutes before you begin work, then remove the airbag, the retaining screws are at the back of the steering wheel down in holes I believe, after that remove the safety clip at the top of the steering wheel threads, then the steering wheel nut, you will need a steering wheel puller to remove the steering wheel, they are about $10 from any parts store, after the wheel is removed remove the airbag clock-spring rotating contact, then remove the turn signal switch, there will be 3 screws holding the turn signal switch in, remove them, then remove the lower trim under the dash and crawl under and and disconnect the large flat connector at the bottom of column, this will allow u to pull the turn signal switch up and out of the way, don't force anything be patient, under the turn signal switch on the right of the area above the ignition lock cylinder u will see a black headed screw, it may be a tamper proof torx/star screw head or a phillips, remove it, then turn the ignition to the on position and slide the ignition switch out, reverse it all and put it back together. take your time, don't rush, good luck, contact me with any further questions.

Posted on Dec 08, 2008

  • 1 Answer

SOURCE: Replaced ignition switch 2003 chevy impala and car will not start

After you replace the ignition switch turn the key to start the car and release leave the key were it stops after trying to start wait 10 minutes until security light goes out turn key to full off position then repeat the above procedure two more times for a total of three on the 3rd attempt to start car wait for light to go out then turn key to full off positoion wait 10 seconds then try to start car body control module should learn new pass code and the car should start.
Big john, J@J Automotive

Posted on Mar 02, 2010

alicantecoli
  • 22219 Answers

SOURCE: How to Remove the Ignition Switch From a 2003 kia

do you have the key?? if so then its relativly easy without teh key you will have to cut the whole lot off

Posted on Jun 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Security light on after replacing ignition switch on 1998 g3500 5.7


Your security module doesn't recognize your key, you may have to get a locksmith or the dealer to make sure you have the right chip in your key to recognize the security module, otherwise youll never get going.

Jan 07, 2015 | Cars & Trucks

1 Answer

No voltage on purple wire @ starter. I have 12 volts on yellow wire coming out of the ignition switch.


You should have 12 volts on the purple wire when you turn the ignition key to start and not in run. If you have no voltage on purple wire at starter (and the wire is clean) when key is turned to start, check the fuses (the fuse block is located behind a cover in the dash to the left of the steering column). If fuses are good you may need an ignition switch. Hope this helps.

Sep 01, 2011 | 1991 GMC G3500

1 Answer

1992 gmc vandura g3500 ecm location


In most gmc/chevy trucks/ vans it is located behind the gove compartment, just remove the glove box and you will see it on top of your heater box.

Oct 25, 2010 | 1992 GMC G2500

2 Answers

2003 Chevy Impala periodically won't start


Try under the dash, attached to colum is a switch that the rod goes into from your ignition key switch, that may need to be adjusted tword your steering wheel just a touch, they go out of alignmnet from time to time

Sep 15, 2009 | 2003 Chevrolet Impala

2 Answers

98 chevy g3500, where is the ignition modual, how do i test it?


your first mistake was buying a reman starter from autozone ....go to napa, oreilly, or anywhere but autozone to buy reman starters
alternators etc ....autozone parts are junk ...
get a new starter motor and replace the autozone one ....

Aug 08, 2009 | 1998 Chevrolet Express

2 Answers

Van keeps running after turning off ignition and removing key


need to check the engine timing and to make sure you have the right octune of fuel in your car.

Apr 09, 2009 | 1984 Chevrolet Chevy

1 Answer

Remove ignition switch


U must dis-arm the airbag 1st, disconnect the battery for 30 minutes before you begin work, then remove the airbag, the retaining screws are at the back of the steering wheel down in holes I believe, after that remove the safety clip at the top of the steering wheel threads, then the steering wheel nut, you will need a steering wheel puller to remove the steering wheel, they are about $10 from any parts store, after the wheel is removed remove the airbag clock-spring rotating contact, then remove the turn signal switch, there will be 3 screws holding the turn signal switch in, remove them, then remove the lower trim under the dash and crawl under and and disconnect the large flat connector at the bottom of column, this will allow u to pull the turn signal switch up and out of the way, don't force anything be patient, under the turn signal switch on the right of the area above the ignition lock cylinder u will see a black headed screw, it may be a tamper proof torx/star screw head or a phillips, remove it, then turn the ignition to the on position and slide the ignition switch out, reverse it all and put it back together. take your time, don't rush, good luck, contact me with any further questions.

Dec 08, 2008 | 2003 Chevrolet Suburban 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...