Question about 1998 Nissan Altima

Open Question

How do you disconnect the alarm system on 2002 Nissan Altima 2.5s

Posted by on

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 383 Answers

SOURCE: replacement of a head gasket on 2.5 liter nissan altima 2002

frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!

Posted on Apr 23, 2009

  • 1 Answer

SOURCE: 2002 Nissan Altima Exterior Door Handle

I seriously doubt that supergluing or even epoxying a handle back will hold at all, or hold for more then few days.
I would only suggest doing the replacement yourself if you familiar with this type of work, or has the aptitude to figure out how to do it, and have the right tools because it is NOT trivial and a number of things can be done wrong, broken or scratched.
The handle itself cannot be replaced. The outside door handle assembly (which includes the handle, the bezel with all associated springs, plastic and metal hardware) has to be replaced. Besides junkyards, which is a long shot for number of reasons, the only place where the handle assembly can be bought is the dealer. And these handle assemblies are not cheap ether. The driver side handle on my 2002 Altima broke first. I paid $60.23+tax, and they had to order it. BEFORE anyone goes to the dealer I suggest to call first, and ask them if they have it in stock. Since door handles are sold painted they will ask you for your car's VIN number so that they match the paint color.
After you pick it up, the replacement will take about an hour (if you know what you doing). The inside door panel has to be removed, it is held in place by the inside door handle and the panel is attached by a number of clips, the handle assembly is attached to the door by three bolts, to remove which you will need a socket with extension. You will also need a good flashlight so you see what you are doing.
If you are familiar how to do this type of work and plan to keep the car for a while I strongly suggest buying a factory service manual on a CD (I bought mine on eBay for under $10). It is worth its price 1000s of times over, and makes almost ALL repair work SOOO much easier.751424a.jpg73e3811.jpgd240851.jpg

Posted on Nov 16, 2009

  • 1 Answer

SOURCE: 2002 Nissan Altima P0720, P1574, P0420

I have a 2002 Nissan Altima. Can anyone tell me what these codes are? And how to fix them? P0420

Posted on Jan 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to check why my car alarm in 2006 nissan altima is not working


If it aftermarket(bunch of wires and modules under the dash on the drivers side) remove it. If it is still factory it takes a scanner.

Dec 03, 2015 | Nissan Cars & Trucks

1 Answer

After setting alarm it sounds off once and then the windows open after car is locked


Reset alarm system. Disconnecting battery leads for thirty min. may do it.

Jun 23, 2015 | 2005 Nissan Altima

1 Answer

Horn randomly honks while key is not present


Some alarm systems use the horn to confirm engagement/disengagement. To randomly work I would suspect an adjustment in the sensitivity of the alarm system or a fault occurring in the system.

Apr 22, 2014 | 2002 Nissan Altima

1 Answer

Nissan altima key fob broke when dropped


The alarm will sound if the alarm was set before you dropped the key fob. Just put the key in the ignition and start the car, the alarm should turn off.

Jan 15, 2014 | 2002 Nissan Altima

1 Answer

Alarm wont chirp when locked 1997 nissan pathfinder


Check your owners manual I believe this can be turned on or off, so you may have it set that way. It would be under vehicle functions or security system in the index.

Jun 22, 2012 | 2002 Nissan Altima

1 Answer

When trying to jump dead battery alarn horn goes off


THE ALARM NORMALLY IS CONNECTTED DIRECTLY WITH THE BATTERY IS PROTECTED BY FUSE OR BREAKER..
Disconnect the fuse or breaker for to avoid the problem
sincerely.
E.CUADRA

Oct 23, 2011 | 2002 Nissan Altima

1 Answer

Changing crankshaft sensor on 2002 nissan altima


I have replaced many of these. What I find works is a small flat screw driver. Pry under the sensor bodyand turn at the same time. That works for me

Nov 10, 2009 | 2002 Nissan Altima

1 Answer

I'acontrol m working on a 2002 nissan altima.


where is the ac relay on a nissan altima 2002

Aug 04, 2009 | 2000 Nissan Altima

1 Answer

Car alarm


dear friend- it appears that your remote lost it code if this is a factory system you can disconnect the battery for a while,but before you do that press the lock and unlock buttons similtanious if it does work disconnect the battery.reconnect and try again do not leave the key in the car when doing this.

Jul 05, 2009 | 2002 Nissan Altima

1 Answer

2002 nissan altima - doesn't have any heat


nissan altima notorious for air pockets in cooling system , bleed system well , make sure cooling system is topped off and retry , cheers .

Jan 12, 2009 | 2002 Nissan Altima

Not finding what you are looking for?
1998 Nissan Altima Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

713 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...