Question about Cars & Trucks

1 Answer

Torque wrench settings for rear hub nut on 2003 Nissan micra

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 14,161 Answers

Posted on Feb 23, 2016

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: Torque specs for front wheel hub nut

112 to 174 ft lbs

Posted on Apr 04, 2009

  • 72 Answers

SOURCE: Front Hub Bearing Torque specs to complete replacement

THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Posted on May 09, 2009

  • 15 Answers

SOURCE: VW Jetta torque setting and hub nut size????

129 ft/lbs. Per Bentley...I'm pretty sure it's a 30 mm 12 point socket.

Posted on Jun 01, 2009

  • 101 Answers

SOURCE: Torque setings

if it is a solid bearing do it up as tight as you can.if it is a tapered bearing do it up untill the nut is touching the bearing check the hub for play if you have got play do the nut up a bit more until the play is gone in the hub.make sure you do not over tighten the bearing or the wheel will not turn freely.the wheel needs to spin with no drag.

Posted on Jul 31, 2009

  • 5 Answers

SOURCE: My nissan micra 2003, malfunction indicator light

OH YES !!!! u have to get ur car computer scanned right away. Theres surely a problem on the way, and before it gets worse, get it scanned and u will easily get to know what needs to be changed. So instead of changing 3-4 things when its gets worse, its better to change only the thing which is required right now.

DO IT RIGHT AWAY !!!

Posted on Aug 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Renault clio2006 mk111 torque wrench setting rear brake hub drum nut Also do you have to fit a new nut


275 Newton meters, yes you should use new nut, but should be fine if nut is in good condition

Dec 03, 2016 | Renault Cars & Trucks

1 Answer

How do you install front hub assembly on 2008 nissan altima?


The torque spec is way more than any torque wrench
you will own

All you can do is get it as tight as possible with a very long
ratchet

The spec are from180 to 230 lbs on some axle nuts

Dec 13, 2012 | Nissan Altima Cars & Trucks

1 Answer

Replace front ball joints on jeep


Hello there,
To replace the front ball joint on your jeep. You will be needing these instruments, Lug wrench Jack, Jack stands, Wheel chocks, Socket set, Wrench set, Needle-nosed pliers, Hub puller, Ball joint separator, Hammer, Ball joint press, Torque wrench, then, Please follow the steps below:
Loosen the lug nuts on your Cherokee's front tires, using the lug wrench. Jack up the front end of the vehicle and brace it with jack stands. Place wheel chocks behind the rear tires to prevent rolling. Back the lugs off the lug nuts, and remove both front tires from your Cherokee.
Remove the bolts behind the calipers. Lift the calipers off the hubs and set them on a support so they do not stretch the rubber lines.
Pull straight out on the brake rotor to remove it from the wheel studs.
Remove the cotter pin from the end of the axle shaft that extends through the hub. This is best done with a pair of needle-nosed pliers. Remove the drive nut from the axle shaft, and set it off to the side.
Remove the three bolts retaining the hub. These 12-point bolts are on the rear of the assembly.
Separate the hub assembly from the knuckle; a hub puller will make this easier.
Remove the cotter pins from the ball joints, using the needle-nosed pliers. You must detach the pins from both the upper and lower ball joints. Use a socket and ratchet to remove the nuts at the bottom of each ball joint.
Insert a ball joint separator between the knuckle and the ball joint. A hammer can be a big help to drive the separator into place and force the knuckle and ball joint apart.
Use a ball joint press to remove the joints. The ball joint press will force the upper and lower ball joints out. Follow the instructions included with your press.
Insert the new joints, using the ball joint press. You must reverse the motion of the press this time, pressing down on the upper joint and up on the lower joint. Be sure that the joints are completely in place within the knuckle.
Reinstall the steering knuckle onto the new ball joints, and thread the nuts onto the bottom of the joint. Check your manufacturer's specifications for the torque requirements for the nuts. Insert the cotter pins, and bend them down around the nut.
Reassemble the hub and axle around the knuckle. When replacing the three bolts, torque them to your manufacturer's specification.
Place the brake assembly back into position, both rotor and caliper. Replace the two bolts you removed on the caliper. Torque the bolts to your manufacturer's specification. Place the wheel back on the Cherokee, and tighten the lug nuts appropriately. With the wheel secured, lower the vehicle back to the ground.
Hope this was helpful to you. Goodluck Elect_Comp

Sep 03, 2011 | Jeep Cherokee Cars & Trucks

2 Answers

Torque on the rear spindle nut of a 1992 mercury cuogar


there is no torque you turn the nut till its thigh than back it off 1/4 turn put the cotterpin in and then the cap

Apr 24, 2011 | 1992 Mercury Cougar

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

Does anyone know the torque wrench settings for the rear hub/wheel bearing nuts on a 2002 Peugeot 206 1100cc please? Also the road wheel bolts?


Tightening torque for the hub nut is 200Nm and the road wheels are 85Nm

NOTE: The rear wheel bearings are remowned on these cars for sticking to the stub axle quite badly, and often have to be forced off using a slide hammer on the drum, it is quite common to end up damaging the wheel bearing, so be prepared to replace this as well in this event

Jan 23, 2010 | 2005 Peugeot 405

1 Answer

Torque setings


if it is a solid bearing do it up as tight as you can.if it is a tapered bearing do it up untill the nut is touching the bearing check the hub for play if you have got play do the nut up a bit more until the play is gone in the hub.make sure you do not over tighten the bearing or the wheel will not turn freely.the wheel needs to spin with no drag.

Jun 02, 2009 | 2003 Renault Sportwagon

1 Answer

Hub nut loosened


The hub nut should have a crowned cover that goes over top of it and a cotter pin hold it and the hub nut in place. Make sure these are not missing. Without the torq specs, tighten the nut handle tight ONLY. (NOT WITH A WRENCH) put crown back on and cotter pin.

Jun 01, 2009 | 2003 Nissan Maxima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

402 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...