Question about Cars & Trucks

1 Answer

How do i replace a broken rear centre bolt on my nissan 4x4

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 94 Answers

They will have your part here http://www.diyobd2.fr/wholesale/kess-v2-obd-tuning-kit-2262.html


let me know if that helps you

Posted on Oct 17, 2013

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

F.U.B.A.R.
  • 19 Answers

SOURCE: two broken lug studs. 07 Nissan titan 4X4.

They should be replaceable w/o pulling the axle. Imagine a common nail; you have the shank of the nail with its point and the flat head on the other end. Your lug stud looks a little like that except the part that comes through the axle flange. It is a little larger than the threaded part and has "lateral lines" machined into it to grip inside the flange. Otherwise it would spin either way when you tried to tighten or remove it. To get the broken ones out, use a high quality flat end punch and a hammer to drive them backwards (toward the center of your differential) and eventually out of the flange. Look for the area that will give you the most room so they will not hit aything while they are backe out of the flange. The new studs can be installed in the reverse manner. When you get them just barely started through the flange, use your fingers to twist them back and forth to "feel" for the grooves where the old stud was seated. Once you get it barely started in the grooves, grease the threads, slip an old 1/2 inch drive socket over the new stud (make sure it doesn't fit tight) slip on a thick flat washer or 2--3 thin ones, turn your lug nut around backwards so the tapered end faces out and begin to tighten it. Go slow, make sure the new stud pulls through the flange evenly. Take the nut, washers and socket off every now and then and look at your progress. When the back side of the stud is seated on the back of the flange, you're finished. Now, always grease the studs. ALL OF THEM, EVERY WHEEL. The monkeys that put on tires these days use impact wrenches and if you just have to let them do it, grease will help you loosen the nut if you have to and it will help prevent future failures. A DRY stud and nut causes a twisting motion to take place in the body of the stud when its tightened. This leads to premature metal fatigue.

Posted on May 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm looking to replace the rear axle on my 1997 4 door 4x4 GMC Yukon 3.73 gears would a rear axle from a 1998 Yukon 4door 4x4 with 3.73 gears bolt directly to my 1997 Yukon


yes
the housings will be the same
clue here --if the diff center comes into the housing from the front not a problem
if it comes in from the rear ( tin cover removed ) replace the complete housing as you will have to have expertise in resetting the bearing pre-loads for the diff center bearings

Jul 15, 2017 | GMC Cars & Trucks

1 Answer

How do l adjust rear wheel tracking on fiat doblo van


if it is a leaf spring set up check for loose "U" bolts or broken centre bolt in the spring pad
if it is an independent rear end take it to an accredited wheel aligner shop and have them align the rear end
mounting points will have en centric washers under the bolts and when they are turned the wheels will align.

Feb 18, 2015 | Fiat Cars & Trucks

1 Answer

Rear Tires: Balding


if it has independent rear suspension then have the suspension rubbers checked and replace if necessary. Next for all wheel alignments it is essential that the rear end is aligned first to stop this tyre wear before the front wheels are aligned . IF you have leaf springs at the rear check for axle alignment and broken centre bolts or worn rubbers at the centre bolt mounts.

Mar 24, 2014 | 2003 Buick Rendezvous

1 Answer

1993 chevy 1500


if there are leaf springs in the rear of both vehicles and the centre bolts of the springs are the same distance apart then it will fit unless the wheels on one are closer to the body than the other. (track) A tape measure will prove this.. The drive pinion and tail shaft u-joint set up should be the same. Check that the diff ratios are the same or you will have transmission problems ( this is the most important point). Difference between front and rear diffs.

Dec 08, 2013 | Cars & Trucks

1 Answer

Exhaust manifold leak


Hi Kevin,should of bought a 85 nissan 720 4x4,lol,here's a link to replacing your gasket,join the site,it's free then you can use their repair guides.Check my video out.

Nov 22, 2013 | 2003 Mazda Tribute

1 Answer

Nissan frontier starter binds the flywheel


You need to put shims in between the starter and the engine block.You should be able to pick them up at your local auto parts store.

Oct 31, 2012 | Nissan Frontier Cars & Trucks

1 Answer

Where is and how to change the cranck sensor on 2000 nissan frontier 3.3 4X4.


Hello shalom570,

The crank position sensor is on the rear left-hand side(drivers side) of the engine. See image below.

netvan_185.png

To replace follow steps outlined below.

1. Disconnect crank position sensor harness.
2. Loosen and remove the bolt securing the sensor.
3. Remove the sensor.

To install revers process.

Regards,

Jerry

Aug 20, 2011 | 2000 Nissan Frontier

1 Answer

How to check transfere case oil 1995 Nissan 4x4


The transfercase is located just off the transmission under the middle of the truck. The check and drain plug should both be located facing the rear. And should both be different from all the other bolts. To remove it should eather be a 1/4 or 3/8 ratchet or close to a 1'' wrench. Hope this helps

Apr 21, 2010 | 1995 Nissan Pickup

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...