Question about Cars & Trucks

Open Question

How to remove brake light cover of chevrolet matiz 2009 after remove two screws?

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

moparownr
  • 667 Answers

SOURCE: Ford Expedition brake light replacement

once those two screws are removed grab both sides of the light and pull out, the lights are held in with to pop locking pins and those two bolts

Posted on Mar 26, 2009

pippall
  • 1486 Answers

SOURCE: Brake light cover wont come off?

you have anouther screw inside on piller.

Posted on May 28, 2009

  • 13 Answers

SOURCE: My third brake light is out and needs replacing

If I remember correctly, you need to pop off the plastic trim panel on the inside of the trunk to access the wiring. Just unplug it after removing all the screws and it should come out.

Posted on Aug 05, 2009

  • 280 Answers

SOURCE: How do I replace the passenger side brake light on

there is most likely a 3rd screw that you can not see because of the trim.

Posted on Mar 12, 2010

alicantecoli
  • 22095 Answers

SOURCE: what tools are needed to replace the front brake

12mm ring spanner and big screwdriver .make sure vehicle has a stand under it as well not just the side jack.

Posted on Apr 03, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the cabin air filter on a 2009 chevy malibu?


It is under the dash on the passenger side of the car. It will be behind a plastic cover with some screws holding the cover on. remove cover and you will see the filter.

Jul 14, 2014 | 2009 Chevrolet Malibu

1 Answer

I have a 2009 Chevrolet Impala, and I want to remove the third brake light to black it out to match the main taillights. How do I get the third brake light lens out?


open the trunk and remo0ve the interior trim panel on the trunk lid. You will see a couple of nuts that hold the lens in place.

Feb 09, 2012 | 2009 Chevrolet Impala

1 Answer

Changing mirrors to camping mirrors, 2009 silverado 2500 HD crew cab LTZ. got mirrors loose, but can't get cord out to unplug and plug in. appears that I have to take door panel off to remove cord and...


remove any snap in covers
remove retaining screws
panel will then lift straight up
snap in cover around door release (open) handel
power windows etc.etc.
retaining screws aroun handel (under plastic snap trim)
around lower section etc. etc.

Jul 02, 2011 | 2009 Chevrolet Silverado 2500HD

1 Answer

I need to replace the driver's side brake light.


Rear Combination Light- 2007 might vary from these diagrams:
Removal & Installation 2004 (Early Production) 4 Door To Remove:
  1. Disconnect battery negative cable.
  2. Disconnect electrical connector. Rear Combination Light kia-06-18-7495.gif

  3. Remove 2 screws and 2 nuts and remove light assembly.
To Install:
  1. Install light assembly and 2 screws and 2 nuts.
  2. Connect electrical connector.
  3. Connect battery negative cable.
5 Door To Remove:
  1. Disconnect battery negative cable.
  2. Disconnect electrical connector. Rear combination light kia-06-18-7496.gif

  3. Remove 2 screws and push light assembly toward outside of vehicle. CAUTION
    Use care to not damage gasket.
  4. Pull rear combination light from vehicle.
To Install:
  1. Install rear combination light and 2 screws.
  2. Install 2 screws.
  3. Connect electrical connector.
  4. Connect battery negative cable.
2004 (Late Production), 2005-2009 To Remove:
Turn Signal Lamp kia-06-20-7698.gif

  1. Disconnect battery negative cable.
  2. Remove 2 screws and cover inside trunk.
  3. Remove 4 nuts and disconnect electrical connector (A).
  4. Remove rear combination lamp.
To Install:
Turn Signal Lamp kia-06-20-7698.gif

  1. Install rear combination lamp.
  2. Install 4 nuts and connect electrical connector (A).
  3. Install cover inside trunk and install 2 screws.
  4. Connect battery negative cable.
prev.gif next.gif

Oct 28, 2010 | 2007 Kia Spectra5

1 Answer

How to change the inside overhead brake lights in an 86 corvette


Hi,
1.Remove the two Phillips head screws from the brake light lens cover.
2.
Pull the lens cover away from the tail light panel. Set it aside on a soft surface because the lens scratches easily.

3.Push in the bad brake light bulb. Twist it counterclockwise to disconnect it from the socket
4.
Insert the new brake light bulb while wearing gloves. Twist it clockwise to secure it to the socket.

5.
Re-position the lens cover. Push it in firmly to secure it, and then tighten the two screws.

Good luck!!!!!

Aug 03, 2010 | 1986 Chevrolet Corvette

1 Answer

No brake lights-changed brake light switch-no fuses blown-all lights and signals are working-NO BRAKE LIGHTS


One of the most common problems with that situation is the turn signal switch. It is most commonly known as the multifunction switch, You can obtain one at an auto parts store. To replace it you will have to remove the cover from around the middle section of the steering column. You should be able to see some holes in the bottom section of the center section, inside those holes are screws that are usually phillips screws or torx(star shaped) screws. Remove those screws and you can remove the switch. The brake light switch power travels through the multifunction switch, I do not know what vehicle you have but I would guess ford or Gm. Hope this helps please leave a comment.

Jun 26, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

Rear brake light and taillight out how to remove cover chevy subu


When you open the rear door there should be 2 screws in the door jam holding the tail light in.

Apr 04, 2009 | 2003 Chevrolet Suburban 1500

4 Answers

Replacing a brake light bulb for a 2006 chevrolet equionx


I just replaced the p/s brake light:
1. Pop off the tabs that cover the screws. (flat screwdriver)
2. Unscrew both screws. (philips-head)
3. There is a metal post attached to the light assembly located towards the front of the assembly pointing in towards the center of the car. This post fits into a rubber grommet that is attached to the car. I had to wiggle and rock the assembly to get the post free from the grommet and the assembly off the car, by pulling to the right.
4. Re-assembly requires lining up and inserting the post back into the grommet (use your best Beavis and ******** sound effect now). Put the screws back in and don't forget the covers.

Jun 20, 2008 | 2006 Chevrolet Equinox

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...