Question about 2003 Nissan Altima

Open Question

What does IPDM MEANS ON A 2003 NISSAN ALTIMA MEANS

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: 2003 Nissan Altima?

Where is the sensor placed on the car?

Posted on Oct 07, 2008

Ad
  • 1 Answer

SOURCE: 2003 Nissan altima alternator

how do yow remuve alternaotor on a 2003 nissan altima

Posted on Jan 05, 2009

breddi2
  • 126 Answers

SOURCE: how many termostats does a 2003 nissan altima have

There is one thermostat for coolant and it is located at the end of top radiator hose inside the kneck that it connects to. To replace this the hose has to be removed and then the kneck,thermostat is brass colored valve that covers center of hole,clean old gasket from block side and kneck replace with new one and gasket with a bit of rtv sealant tighten kneck evenly when putting it back on,connect hose wait a short while for rtv to set up and should be good to go,"make sure engine is full of coolant b4 reassembling,just pour strait in engine if it isn't or you can damage new thermostat.overheating can also be sign of water pump not working as well so if still having problem then it is possible cause and on older models radiators get clogged.

Posted on Apr 20, 2009

emissionwiz
  • 76630 Answers

SOURCE: Is there a way that I can reprogram a key fob

yes u can and here is the procedure.
1. Close and lock all doors with the driver’s side power lock/unlock switch.

2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Hazard
Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition cylinder
each time. If this procedure is performed too fast, system will not enter programming mode.

3. Insert key into the ignition cylinder and turn to the ACC position.

4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not press
the button more than one time in the above step. If the button is pressed more than one time, the programming
procedure will not be successful.


5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side
power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing transmitters).

6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/unlock switch and open the driver side door.

Posted on Jun 12, 2009

  • 25 Answers

SOURCE: how to replace the crankshaft sensor on 2003 Nissan Altima

The cam sensor is mounted in top of the engine on the right side of the engine where the tranny mounts. You have to remove the top cover of the engine to get to it. Remove the electrical connector from the sensor, there is a clip that holds the connector in place. Push down on the back of it and then pull back at the same time. Pull on the connector and not the wires, they are very small and will break. Remove the bolt holding the sensor. To remove the sensor by twisting and pull on it at the same time. Is the engine not running, why are you replacing the cam sensor?

Posted on Sep 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the passenger side low beam fuse located on a 2006 Nissan Altima


Low Beam Operation With the lighting switch in 2ND position, the BCM receives input requesting the headlamps to illuminate. This input is communicated to the IPDM E/R across the CAN communication lines. The CPU of the IPDM E/R controls the headlamp low relay coil. When energized, this relay directs power ? through 15A fuse (No. 36, located in the IPDM E/R) ? through IPDM E/R terminal 20 ? to headlamp RH terminal 1, and ? through 15A fuse (No. 45, located in the IPDM E/R) ? through IPDM E/R terminal 30 ? to headlamp LH terminal 1. Ground is supplied ? to headlamp RH terminal 2 ? to headlamp LH terminal 2 ? through grounds E15 and E24. With power and ground supplied, low beam headlamps illuminate.

IPDM E/R - fuse box E/R -- engine room , under hood fuse box .

System Description EKS008LH Control of the headlamp system operation is dependent upon the position of the combination switch (lighting switch). When the lighting switch is placed in the 2ND position, the BCM (body control module) receives input requesting the headlamps (and tail lamps) to illuminate. This input is communicated to the IPDM E/R (intelligent power distribution module engine room) across the CAN communication lines. The CPU (central processing unit) of the IPDM E/R controls the headlamp high and headlamp low relay coils. When energized, these relays direct power to the respective headlamps, which then illuminate. OUTLINE Power is supplied at all times ? to headlamp high relay, located in the IPDM E/R, and ? to headlamp low relay, located in the IPDM E/R, and ? through 50A fusible link (letter f , located in the fuse and fusible link box) ? to BCM terminal 70. With the ignition switch in the ON or START position, power is supplied ? through 10A fuse [No. 1, located in the fuse block (J/B)] ? to BCM terminal 38. With the ignition switch in the ACC or ON position, power is supplied ? through 10A fuse [No. 6, located in the fuse block (J/B)] ? to BCM terminal 11. Ground is supplied

https://carmanuals2.com/brand/nissan/altima-2006-4924

May 05, 2017 | Nissan Cars & Trucks

1 Answer

Replaced engine fuse box (with ipdm )on 2003 Nissan Altima SL and now the wipers will not turn off even with switch removed


With IPDM - intelligent power distribution module . Pull the front wiper relay and front wiper hi relay , see if they reset . If that doesn't work you'll need to take it to the dealer an have them reset with factory scan tool . Also ,sometimes new modules need to be programmed . Download 2003 Nissan Altima Wiper Washer Section WW PDF Manual 36 Pages

Feb 14, 2017 | Nissan Cars & Trucks

1 Answer

Where is the fuel pump relay located? Altima 2005


Its located in the IPDM box....remove the cover and you ll see a side with 4 relays close to the fuses and the other side 3line of relays,the relay in the middle is your fuel pump relay......hold the ipdm in position the fuses in the box upside....

Nov 01, 2013 | 2005 Nissan Altima

1 Answer

Ipdm


REPLACED THE WRONG COMPONENT...OR NOT FOUND THE COMPLETE ISSUE

Jul 21, 2013 | 2003 Nissan Altima

3 Answers

Low beam headlight doesn't work after replacing with 3 new ones. Any suggestions?


My 2003 Altima had a similar issue...Long story, short....I located a blown fuse (location 49 & 50) for the low beams in the IPDM E/R and replaced it. The headlight worked right away. My IPDM E/R was under the hood close to the front passenger side head light and coolant bottle.

May 07, 2010 | 2005 Nissan Altima

1 Answer

THE AUTO DOOR LOCK AND POWER WINDOW DO NOT WORK AND I CANT FIND THE FUSE FOR THEM ON 2005 NISSAN ALTIMA


From the service manual, which is available relatively inexpensive at Promanuals.net here

 Both front wiper relays are located in the IPDM E/R (intelligent power distribution module engine room)
 Wiper switch (combination switch) is composed of a combination of 5 output terminals and 5 input terminals.
Terminal combination status is read by BCM (body control module)
 BCM controls front wiper LO, HI, and INT (intermittent) operation
 IPDM E/R operates the wiper motor according to CAN communication signals from the BCM.
Power is supplied at all times
 through 50A fusible link (letter f , located in the fuse and fusible link box)
 to BCM terminal 70, and
 through 20A fuse (No. 39, located in the IPDM E/R)
 to front wiper relay, located in the IPDM E/R
With the ignition switch in ON or START position, power is supplied at all times
 through 10A fuse [No. 1, located in the fuse block (J/B)]

Sep 28, 2009 | 2005 Nissan Altima

3 Answers

No low beam head lights


If you just want to replace the bulb yourself, this is a good website.
http://www.paulstravelpictures.com/Nissan-Altima-Headlight-Bulb/Nissan-Altima-Passenger-Side-Headlight.htm
If the website does't get your headlight fixed... You might have a blown fuse. It could be in the IPDM E/R location under the hood. This is next to the coolant bottle. Remove the coolant bottle with two screws and lift the cover to the IPDM E/R. Just set the coolant bottle aside for now. The low beam fuses are 49 and 50. They are 15A fuses. To be more precise, they are located on row 2, columns 2 and 3 (column 1 being closest to the fender of the car). Hope this helps.

Jan 04, 2009 | 2003 Nissan Altima

3 Answers

2003 Nissan altima alternator


The alternator is right on top of the 2.5L motor and held on by 2 14mm bolts. To remove the lower bolt (hard to reach), you must remove the coolant bottle and the IPDM fuse board and its metal box/bracket. A breaker bar really helped give enough torque to loosen the bolts. Approach the drive belt from under the front passenger tire. There is a tension adjuster (hard to reach) bolt that loosens the belt and allows you to remove it from the alternator.

Aug 21, 2008 | 2003 Nissan Altima

Not finding what you are looking for?
2003 Nissan Altima Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...