Question about 1994 Geo Tracker

Open Question

I have a 1994 geo tracker that at 55 mph runs at 3000 rpm is this right?

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 398 Answers

SOURCE: what are the symptoms of a bad egr valve ina 1994 geo tracker?

this may help
EGR Theory. EGR serves one purpose and one purpose only. That purpose is to reduce Oxides of Nitrogen (NOx). Undernormal combustion, Nitrogen(N2)Oxygen (O2) in the air and Hydrocarbons (HC) in the fuel combind into water(H2O) Carbon dioxide (CO2) and the Nitrogen remains unchanged. Under very hot combustion temperatures, the Nitrogen reacts with the other two byproducts and forms Nitrogen oxide (NO). After being released into the atmosphere, it picks up another Oxygen and becomes Nitrogen dioxide (NO2). In the presence of sunlight,
it combines with other compounds like Hydrocarbons and forms Smog. Since exhaust gas is inert (very stable) it doesn’t burn again. So by being introduced into
the combustion chamber, it will lower combustion chamber temps enough so that
the Nitrogen doesn’t react with the other compounds and is passed unchanged out
the tailpipe thus not contributing to smog. Now, since exhaust gas doesn’t burn, it
doesn’t exactly help with combustion. At higher RPM’s, this really isn’t noticable,
but at idle, the reintroduction of exhaust gas will cause a very rough idle and can
cause stalling if to much is introduced into the combustion chamber

Posted on Mar 07, 2009

Ad
  • 337 Answers

SOURCE: 1992 geo tracker will not run

The ECM has a blown capacitor inside it for opening the injector you will most likly need to get it rebuilt, buy a new ,or used ECM had the same problem with my sidekick.

Posted on Mar 16, 2009

  • 14036 Answers

SOURCE: 94 & 95 Geo Tracker obd1 cable

you need the same brand cable.

Posted on Apr 06, 2009

  • 2 Answers

SOURCE: reset check engine light on 1995 geo tracker

I had the very same problem with my 94 tracker and it turned out to be something simple. My check engine light had popped on after it had hit 100,000. I went through all of the suggestions that people had suggested (unplug battery......etc) and still to no avail. Searching the internet, I came across a website called suzukiforum.com and there, this guy was able to help me with my problem. It turned out to be a maintenance switch that kicks on every 50,000 miles. This switch is like a secret that the auto manufactures use to ploy owners of their cars to bring to the dealer and then rack up the dollars in unnecessary "repairs". The switch is located under the dash and can be hidden anywhere. From the assistance of the guy on the forum, he was able to send me photos of this damn switch and possible locations where it may be mounted. I found mine in about 5 minutes, where it was attached to the steering column. It's a tiny switch, that you slide up or down, depending on what position it is in upon finding it. If it's up, then slide it in the down position and visa versa. Once you do this, the check engine light will go off. Make sure you do not have the car running and you can even unhook one of the battery posts, just to make sure you don't hit anything while rooting around under the dash. Good luck!

Posted on Apr 30, 2009

  • 72 Answers

SOURCE: 1995 4x4 geo tracker front wheel bearings

first you remove the wheel then the break caliper then remove the locking hubs just remember to lay out the parts in order a special tool is called for but this job can be done without it you have to use a small cold chisel and a hammer to tap the large nut counter clockwise to remove, you can then remove the outer bearing and the rotor and hub assembly look on the back side reomve the bearing seal and inner bearing be sure to pack your new bearings with grease before you reassemble . takes less than an hour.

Posted on May 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

97 tracker drive fine forword but i have to rev it uo to 3000 rpm befor revers gear grabs?


try changing filter in transmission. sounds like filter may be stopped up.

Nov 10, 2013 | 1997 Geo Tracker 2 Door

1 Answer

1995 geo tracker .. when start the truck it idles at 3000 rpm and when shifting between gears it idles high at 3000 rpm .. it randomly started this but i also noticed when it started doing that my lighter...


Hello,
I doubt it has anything to do with your lighter/aux, but change the fuse on it and see if that corrects the problem. Check to see if you can pull the gas pedal back with your hand and see if that lowers the RPM. Old cars can wear the parts that make your pedal rise fully back up.
There is also the intake adjustment screw near where your intake meets the manifold. It's usually a phillip's screw. This will lower or raise your RPM levels on idle. You may have to adjust the screw. Every time you make 1/4 turn adjustments, you need to let the car run for awhile as the process is gradual and NOT immediate. This is the steps I would take because I know my cars, but if you feel uncertain, please take it to a mechanic. Best of Luck!

Feb 17, 2011 | 1995 Geo Tracker

1 Answer

1994 Geo Tracker 4x4 auto.Problem is that it wont shift until about 4000 rpm.Replaced modulator & did fluid & filter change.No help.What can I do now?Does this tranny (3-spd auto) have a governor?


yes that tranny has a governor. take off the transfer case and where the transfer case bolts to the transmission there is a ext. housing take off also and its bolted to the park shift gear check the govenor valve body for cracks.

May 31, 2010 | 1994 Geo Tracker

1 Answer

1990 geo tracker There is a little button at the base of the


could be a hold button to hold that gear or a overdrive button or traction control. i would drive it up to 55 mph and click the button in if the car revs up or shifts its a overdrive button or traction control. I would leave it unclicked.

Feb 06, 2010 | 1996 Geo Tracker 2 Door

1 Answer

1994 Geo Tracker 4x4 Automatic


it is probably out of water as mine did that and the radiator was dry. due to a bad water pump.

Nov 02, 2008 | 1992 Geo Tracker

Not finding what you are looking for?
1994 Geo Tracker Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...