Question about 2000 Mercedes-Benz SLK

Open Question

Clear permanent obd2 error codes - 2000 Mercedes-Benz SLK

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to clear po171 error code on ecm?


I assume you have corrected the fault that caused this lean code to set. If so either use a OBD2 code reader to clear the code or try disconnecting the battery negative for 5 minutes, I do not recommend this as it can cause other problems due to lost stored programming. Many auto parts stores have code reader and will clear the code for you

Jul 18, 2016 | Cars & Trucks

1 Answer

How do i clear error code loose gas cap


Ignition on engine not running: clear codes Thats if you are using an OBD2 scanner. and the cap is secure

Oct 17, 2014 | Cars & Trucks

1 Answer

Error code P1110


Without the vehicle make you will not get the correct response, however the genric meaning of this code is:
IAT Sensor (D/C) Open/Short
OBD2 Check Engine Fault Codes Android Apps on Google Play

Mar 07, 2014 | Cars & Trucks

1 Answer

Check Engine Light 2003 X' Type 2.5 Told that previous owner drove the car for a long time without resetting and it will take 3 to 15 resets before it sets permanently. No codes show up on the reader...


When you reset a DTC (Diagnostic Trouble Code) on any OBD2 vehicle (Late 97 and up) you have to drive it for an unspecified period of time after the code is cleared before it will pass an emissions test. This is so people don\'t clear them right before going for an inspection.
If the light was on, there is a problem. Rarely does resetting the code fix it. I would run it until the light comes on then read the code. You can assess the problem from there.

Jun 18, 2013 | Cars & Trucks

1 Answer

Error code on air bag system .code 52


you should try to clear the error code with OBD2 code scanner, if the airbag light come on again, that there have some problems on your airbag system, you must take your car to the car repair shop.

Sep 03, 2012 | 1998 Ford Explorer

1 Answer

How do I "clear a code" out of my "OBD2" system, MYSELF ?


If you go to a local autozone, they will scan/clear ODB2 codes on your vehicle for free.

Jul 18, 2012 | 2003 Ford Explorer

1 Answer

Have 2000 Toyota Camry XLE. Check Engine light appears. Code shows P1035 for Oxygen Sensor Bank 1 Sensor 1 being defective. Replaced sensor. Cleared computer code. Let engine idle for 30 minutes before...


What your asking, is how to make a malfunction light
go away from your dash, so you can forget you have a
problem & make no attempt to repair the car

Until you find & resolve active OBD2 Codes that actually set
a MIL or Check Lamp it will keep coming back

Every time you clear a code you have to run a drive cylce in
some cases to start the procees over, as you need those codes
to diagnose the issues

The codes that are there, do not tell you what to replace

Without writing a book here, just study OBD Systems online &
take the car to a repair shop

It is beyond your ability at this time to figure out

Sep 22, 2011 | 2000 Toyota Camry

1 Answer

OBD2 "check engine lite" shows


Both codes are system too lean bank 1 & bank 2. First place to start is any obvious vacuum leaks. Look for broken,collapsed or missing vacuum lines. Check egr valve & intake manifold also.

Dec 14, 2010 | 2003 Cadillac Escalade Ext

1 Answer

How do I clear the error codes on a 2001 Dodge Ram 3500 diesel?


You will need a hand-held obd2 scanner to clear the codes. Advanced Auto store will do it for free if you have one in your area. Other part stores will also do it for free.
You can disconnect the negative battery cable for 10 minutes and replace it, but it doesn't always work. Sometimes the codes are stored in memory and require the hand-held obd2 to clear them

Apr 19, 2010 | 2001 Dodge Ram 3500 Truck

1 Answer

2001 new beetle won't start has new battery


I have a 2003 new beetle TDI. I have got error codes on my ECM that have stopped my engine from starting. I got an OBD2 reader from the auto parts store. I plugged it into the OBD2 port below the steering wheel and got the error codes. After writing them down, I cleared the codes. the car started fine. It has pulled this a couple times over three years. I carry an OBD2 reader with me so I can clear the codes and get going again. Good Luck

Sep 25, 2009 | 1998 Volkswagen Beetle

Not finding what you are looking for?
2000 Mercedes-Benz SLK Logo

Related Topics:

227 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

yadayada
yadayada

Level 3 Expert

75822 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...