Question about 1990 Isuzu Pickup

1 Answer

Need to set the timing of the cam and crankshaft

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Finish all ready for exact timing of crank shaft,becouse have a timing mark. not same camp shaft,no marking for exact timing.you have a picture for exact timing jb1 engene?thanks sir,

Posted on Dec 03, 2013

  • Tolits Babas
    Tolits Babas Dec 03, 2013

    finish all ready for exact timing of crank shaft,becouse have a timing mark. not same camp shaft,no marking for exact timing.you have a picture for exact timing jb1 engene?thanks sir,

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

SETTING THE TIMING/93 SC400


Setting the cam timing in the SC400 incorrectly can result in valve damage and possible piston damage. If you already have it apart it may be too late. The engine has to be at TDC for the crankshaft before removal of the timing belts. Rolling the cams independent of crankshaft will cause an open valve to contact the piston.(very expensive)

May 19, 2017 | Cars & Trucks

1 Answer

Set timing 95 windstar 3.8


Hello, Ford Windstar timing for the timing of the crankshaft in reference to cam shafts. First, you'll need an auto repair manual for 1995 Ford Windstar with 3.0 engine. Any auto store will have these auto manual for those who like to do it their self's.

Read the disassemble instruction make careful notes on where parts when they come off and where they go back. Follow the linement instruction for the cams and the crankshaft. These lineament marks on the cam sprocket and the cam drive gear on the crankshaft will have to be in there proper location--timing marks. Double or even triple check this lineament procedures and what is specified in the repair manual. I hope this will really help you out. GB...stewbison

Oct 19, 2011 | 1995 Ford Windstar

1 Answer

Need timing blet diagram 1992 ford ranger 2.3


Hi, the crankshaft marks are on the belt pulley and timing cover, so you have to mate it up to see them. The cam sprocket mark goes on the bottom, and aligns with another mark on the timing cover. There is a plug you pull out and hole to look thru to align the cam sprocket/shaft.


jturcotte_1801.gif


jturcotte_1802.gif


Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

Jun 01, 2011 | Ford Ranger Cars & Trucks

2 Answers

On 2000 mazda protege 1.6 replaced water pump now won't start, thinking timing now out what is timing procedure?


i dont have a more detailed picture of setting the timing marks for the belt so i hope this helpsonetufshoppe_81.gif

Jan 30, 2011 | 2000 Mazda Protege

1 Answer

How do you set the timming on a 2.3 when your putting the new timming belt on


The IGNITION timing on your Ranger is computer-controlled and is not adjustable.


Should the camshaft drive belt/timing belt jump timing by a tooth or two, the engine could still run; but very poorly. To visually check for correct timing of the crankshaft, auxiliary shaft, and the camshaft follow this procedure:
There is an access plug provided in the cam drive belt cover so that the camshaft timing cam be checked without moving the drive belt cover.
  1. Remove the access plug.
  2. Turn the crankshaft until the timing marks on the crankshaft indicate TDC.
  3. Make sure that the timing mark on the camshaft drive sprocket is aligned with the pointer on the inner belt cover.

Never turn the crankshaft of any of the overhead cam engines in the opposite direction of normal rotation. Backward rotation of the crankshaft may cause the timing belt to slip and alter the timing.
REMOVAL & INSTALLATION

See Figures 1, 2 and 3


0996b43f80211842.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Timing belt cover on the 2.3L and 2.5L engine


0996b43f80211843.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Timing belt assembly on the 2.3L and 2.5L engine


0996b43f80211844.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 3: Releasing the timing belt tensioner using a special tool

  1. Rotate the engine so that No. 1 cylinder is at TDC on the compression stroke. Check that the timing marks are aligned on the camshaft and crankshaft pulleys. An access plug is provided in the cam belt cover so that the camshaft timing can be checked without removal of the cover or any other parts. Set the crankshaft to TDC by aligning the timing mark on the crank pulley with the TDC mark on the belt cover. Look through the access hole in the belt cover to make sure that the timing mark on the cam drive sprocket is lined up with the pointer on the inner belt cover.

Always turn the engine in the normal direction of rotation. Backward rotation may cause the timing belt to jump time, due to the arrangement of the belt tensioner.
  1. Drain cooling system. Remove the upper radiator hose as necessary. Remove the fan blade and water pump pulley bolts.


Dec 11, 2010 | 1995 Ford Ranger Supercab

1 Answer

Head gasket got bent and I have replaced it . Now the problem I'm facing is how to set the crank shaft and the comshaft timing. I need the procedure for engine timing


Timing Chain & Gears Removal & Installation To Remove:
NOTE: Keep the cam chain away from magnetic fields.
Crankshaft set at TDC marks hnda_trk_crv_crank_tdc_marks.gif

  1. Turn the crankshaft pulley so its Top Dead Center (TDC) mark (1) lines up with the pointer (2).
  2. Raise and support the vehicle.
  3. Remove the front tires/wheels. Front undercar splash shield hnda_trk_crv_frt_under_splsh_shld.gif

  4. Remove the front undercar splash shield.
  5. Remove the drive belt.
  6. Remove the cylinder head cover (See section on Valve Cover).
  7. Remove the crankshaft pulley (See section on Crankshaft Damper). CKP sensor and VTC solenoid electrical connectors hnda_trk_crv_ckp_vtc_ele_conn.gif

  8. Disconnect the Crankshaft Position (CKP) sensor connector (1) and Variable Valve Timing Control (VTC) oil control solenoid valve connector (2).
  9. Remove the VTC oil control solenoid valve (See section on VTC Solenoid Valve).
  10. Support the engine with a jack and wood block under the oil pan. Ground cable and upper bracket removal hnda_trk_crv_grnd_cbl_uppr_brckt_rem.gif

  11. Remove the ground cable (1), and remove the upper bracket (2). Side engine mount bracket removal hnda_trk_crv_side_eng_mount_brckt_rem.gif

  12. Remove the side engine mount bracket. Timing chain cover removal hnda_trk_crv_timng_chain_cov_rem.gif

  13. Remove the timing chain cover bolts both from the front to the block and from the bottom to the oil pan.
  14. Remove the timing chain cover.
  15. Loosely install the crankshaft pulley. Compress the timing chain auto-tensioner hnda_trk_crv_compr_tim_chain_auto_tensnr.gif

  16. Turn the crankshaft counterclockwise to compress the auto-tensioner. Lock the timing chain auto-tensioner hnda_trk_crv_lock_tim_chain_auto_tensnr.gif

  17. Align the holes on the lock (1) and the auto tensioner (2), and then insert a 0.06 inch (1.5 mm) diameter pin (3) into the holes.
  18. Turn the crankshaft clockwise to secure the pin. Removal of the timing chain auto-tensioner hnda_trk_crv_rem_tim_chain_auto_tensnr.gif

  19. Remove the auto-tensioner. Removal of the timing chain guide B hnda_trk_crv_rem_tim_chain_guide.gif

  20. Remove the cam chain guide B. Removal of the timing chain guide A hnda_trk_crv_rem_tim_chain_guidea.gif

  21. Remove the cam chain guide A (1) and tensioner arm (2).
  22. Remove the cam chain.
prev.gif next.gif

Oct 11, 2010 | 2002 Honda CR-V

1 Answer

Timing marks for the Dodge 2.4L caravan, 2000


To align both sets of timing marks, turn engine crankshaft to the right with belt on cam and crank. Once you have done this the crankshaft alignment mark (on front of crankshaft gear) will line up with mark to the rear of gear on engine block.The two cam gear timing marks should be alines across from one another. The right cam gear is the intake side and the left side is the exhaust side. After removing the belt turn the exhaust cam down 1/2 notch. Timing mark on exhaust 1/2 notch down from the intake side. Install new belt and recheck everything to make sure it's all correct. Hope this will help you.

May 16, 2010 | 2000 Dodge Caravan

1 Answer

How to set timming belt,cant find mark for crankshaft 3.0L


Timing belt removed, static timing was not set before removing timing belt.

[Set Static Timing:
No.1 piston is brought up to TDC before removing timing belt.

Cam gear has a punchmark on face of gear, and this mark aligns with one single tooth. There is a matching punchmark on the Timing Belt Rear Upper Cover.

Facing the cam gear, the mark is to the upper right. There is an 'egg shape' of the timing belt upper rear cover, in this spot. This punchmark is in that 'egg shape', and is close to a bolt hole. The cam gear mark lines up with the Timing Belt Rear Upper Cover, mark.

The crankshaft gear has a punchmark on the face. It lines up with one single tooth. There is a corresponding punchmark on the lower right side. An alignment mark)

Should be a round punchmark on the face of the crankshaft gear. It lines up with a single tooth. Wipe the gear clean, use a little carb cleaner. (NO flames, or sparks nearby, well ventilated area)

Barring you cannot find the crankshaft mark, find the camshaft alignment marks, make sure they are aligned with the alignment, (Punchmark), on the Timing Upper Rear Cover.

Count the teeth in the timing belt. There should be 133 teeth on the belt.

There is 43 teeth in-between the timing mark of the camshaft, and the timing mark on the crankshaft.

(43 teeth in-between the Right Side Camshaft mark to crankshaft mark, 43 teeth in-between the Left Side Camshaft mark to crankshaft mark)

There should be 40 teeth in-between the two cam gears.




Oct 24, 2009 | 1989 Nissan Pathfinder

1 Answer

Were does the cams need to be to set the timing on 97


I'm going to send you two exploding views of your crankshaft and camshaft alignment marks.bcaed28.gifd080635.gif

Oct 05, 2009 | 1997 Toyota Corolla

1 Answer

91 chevy G20


well not sure exactly why it wont line up use something to turn the crank and cam to appropiate position start sliding crank gear until cam gear is touching then start to push both at same time make sure your crank key and cam pin are bothin place On many OHV pushrod engines, the crankshaft sprocket is installed on the crankshaft nose and the crankshaft is rotated to position piston #1 at TDC. At this point, a mark stamped onto the crankshaft sprocket is pointing directly upward (toward the camshaft).
The camshaft sprocket is then temporarily bolted to the cam and used to rotate the cam until a mark stamped on the cam sprocket is pointing directly downward (toward the crankshaft). The sprocket is then removed from the cam (without allowing the cam to rotate).
The timing chain is looped over the cam gear, the mark on the cam gear is positioned directly downward, and the chain is looped around the crankshaft sprocket. When the cam sprocket is attached to the cam, the timing marks on the crank and cam sprockets should be pointing toward one another.

Feb 10, 2009 | 1992 Chevrolet G20

Not finding what you are looking for?
1990 Isuzu Pickup Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...