Question about Cars & Trucks

1 Answer

2002 s10 2wd 2.2l man trans. Engages while moving aways when shifting and the clutch is near fully out

Posted by on

  • bucky brown Oct 17, 2013

    sorry starter Engages while shifting gears

  • Joseph Raper
    Joseph Raper Oct 18, 2013

    my friend ,,I see this daily and the pressure plate is hitting your starter ..you need to change clutch pressure plate and throwout bearing ..Good Luck

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Cars & Trucks Master
  • 377 Answers

You must changed your pressure plate most likely as well as the throwout barring ..It is totally going to strand you somewhere soon ..God Bless

Posted on Oct 17, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
justuscc
  • 360 Answers

SOURCE: jdm 1996 honda prelude SiR (4ws) BB8, tiptronic, h22a, 2,2l

any codes? the trans computer will store them. also the engine computer this is an obd2 car autozone can scan for free

Posted on Sep 20, 2008

  • 1861 Answers

SOURCE: Clutch pedal sometimes engages when near floor

Hi. Let me try to lend you a bit of assistance, also.
My fellow expert Benimur is very correct with his input to you.

But...Air does not get into your clutch hydraulics unless the fluid has leaked out at some point. As long as the cylinders and tubes are intact, I would doubt that air is the issue. Short of pulling the transaxle, and inspecting the clutch, there is really no other way to determine your issue properly.

Personally, I think that you haven internal problem with the clutch assembly. It could be worn fingers on the clutch plate, a worn clutch disc, or something as simple as the throwout bearing is hanging up on the input shaft collar.

If Beni's suggestions does not help, you are going to need to pull the trans off, and inspect the clutch items mentioned above.

Thanks for choosing FIxYa, we wish you the best of luck; let us know how it turns out.

Posted on Mar 04, 2009

  • 126 Answers

SOURCE: 2002 Sunfire

check automatic adjuster on clutch pedal under dash .

Posted on May 08, 2009

pippall
  • 1486 Answers

SOURCE: 2002 2.0L Passat petrol: Clutch biting point problem

your pressure plate is damaged.Replace cutch asseberly

Posted on Jun 12, 2009

  • 811 Answers

SOURCE: 4r70w transmission shifting problem

change trans fluid and filter , possible get trasns flushed check electrical connections

Posted on Sep 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Won't move


my beet mate will be the clutch if it goes into gear and it wont move yeh most common is blowen clutch if it is and auto cheek the trans oil level if that is ok it could be your tourqe converter both ways the gear box or trans will need to come out

Jun 26, 2012 | 1999 Jeep Grand Cherokee

1 Answer

On my 99 camry 2.2 4 cyl my clutch pedal catches all the way out. Is it possible to adjust it so it catches farther in?


Yes, there is an adjustment that would have the effect of shifting the point at which the clutch engages, BUT, that would not correct what appears to be your problem. As the clutch wears, the point at which it engages shifts, moving further outward until it will slip even though the pedal is completely out. I suspect that your clutch is nearing its end of life.Toyotas are such reliable beasts however, it would make sense to replace the clutch. I replaced mine at 212,000 miles, and in now has 289,500 miles and is still going strong. Hope this helps. Dano

Aug 31, 2011 | 1994 Toyota Camry

2 Answers

93 Mitsubishi 3000gt overdrive problem


I think rebuild try and service it if you find any lining material in the pan bad news

Jun 06, 2010 | 1993 Mitsubishi 3000GT

1 Answer

How do I adjust the clutch? Clutch engages when


A high clutch pedal is good.
There should only be about a half inch of pedal freeplay, before you start to feel resistance.
So the clutch should not engage until it is almost fully released, near the top.
The makes shifting the easiest.

If the shifting is difficult when cold, then put the transmission in neutral and let the clutch out when you warm up the engine.
That will warm up the transmission oil.

Of course you could also check the transmission oil level and change it.
But your question makes me believe you may need more experience on a stick shift. Make sure you do the H pattern carefully, and do not get lazy and turn it into an X pattern.

May 28, 2010 | 2003 Ford Focus

1 Answer

Gear shifting


Adust clutch cable.Test...start the car in first gear with clutch fully depressed, parking break off. Slowly release the clutch. determine when the vehicle starts to move. If clutch is fully depressed call that 100%, fully released is 0%. The vehicle should be moving at around the 55-45% range.

Dec 02, 2009 | 2002 Nissan Xterra

2 Answers

4r70w transmission shifting problem


change trans fluid and filter , possible get trasns flushed check electrical connections

Sep 16, 2009 | 1995 Ford F150 Styleside Regular Cab

3 Answers

HELLO EXPERTS I have a 1995 jeep wrangler with 2.5 engine and five speed trans. I've put about 1000 miles on a new clutch, pressure-plat, throw-out bearing and slave cylinder. I am experencing the...


Check all your hydraulic connections for seepage . If you find nothing leaking, check where the rod goes into the master cylinder under the dashboard...If still nothing, I'd change the master cyl, as it is likely internally bypassing and permitting the clutch to release. PS it takesa a special "touch" to shift gears without using the clutch, if you cannot do that don't drive it Till you get it fixed...you will damage synchros and will need to have trans removed and rebuilt. $$$you don't want to spend!!!

Jul 12, 2009 | 1995 Jeep Wrangler

1 Answer

Clutch


mcdevito75 here, Sounds like you need the clutch adjusted. have your local shop check it out for you.

Mar 24, 2009 | 2006 Dodge Ram 3500 Truck

3 Answers

Clutch pedal sometimes engages when near floor


Check fluid level on clutch reservoir. Check also for any leaks at the clutch clyinders and lines. if it is low on fluid, or you have to drain fluid, remember to bleed the clutch.Have somebody pump the clutch and turn the clutch bleeding screw until only fluid comes out.

Feb 28, 2009 | 2005 Toyota Corolla

1 Answer

My 2002 Chevy Venture rolls while in park. I accidentally hit the gear shift into park while moving.


when the trans went into park it most likley broke the small rod that engages park and unless you are a capable mechanic with a repair manual you should leave fixing that to a pro hope this helps you

Jan 18, 2009 | 2002 Chevrolet Venture Passanger

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...