Question about Cars & Trucks

1 Answer

Clutch master cylinder not bleeding.

2000 camaro ss, I'm trying to bleed my clutch system but I'm not getting any pressure to my pedal. I put a new master cylinder in. I press the pedal and for about 50 times and the reservoir doesn't even have any drop in fluid. The line from the reservoir to the master cylinder isn't cinked so idkidk.what's hap

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 2 Answers

You will have to bench bleed the line to get aall the air out

Posted on Oct 16, 2013

  • adam bradley Oct 17, 2013

    How do I do that?

×

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
  • 483 Answers

SOURCE: So I just changed the clutch master cylinder and the braided brake line in my 2000 camaro ss and am trying to bleed the system. The routine I'm using is typical. Pump the pedal 30 times keep it depres

you have someone helping you right? cuz you cant do it yourself, and the brakes need to be pumped only enough to get a solid midway stop of pedal travel, and with the brake still depressed by your assistant, you open the bleeder a bit until the pedal goes to the floor, you tighten bleeder, they then release brake pedal and pump it up again, rinse, repeat, until there is no spongy feel in brake pedal

Posted on Mar 21, 2013

  • 1 Answer

SOURCE: I replaced the clutch master cylinder and the braided brake line in a 2000 camaro ss and I'm trying to bleed the system. I know how to do it but I've done the procedure 20 times and there is still no

Assuming the replacement clutch master is not defective, you may need to replace the slave cylinder located at the transmission. Bleeding of the clutch system is done at the slave cylinder. Hope this was helpful.

Posted on Mar 22, 2013

udesh99
  • 97 Answers

SOURCE: bleed clutch system

check whether flow divider valve or Load sensing valve connect to the brake system & re correct them.

Posted on Apr 15, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where the heck is the reservoir for the clutch master cylinder on my 84 AMC Eagle.


its made on clutch master cylinder under hood straight thru from clutch pedal fill it under hood take small wrench 5/16 I think get under vehicle find slave cylinder bleed valve you will need wrench a piece of vacuum hose and a cup put wrench on bleed valve then put vacuum hose on next the other end goes in cup of brake fluid to prevent air sucking back it can bubble air out but can only suck brake fluid back have helper pump clutch pedal hold pedal bleed repump rebleed till clutch gets right its harder to bleed than brakes pump fast hold pedal down pump clutch fast hold down bleed real pain in *ss good luck

May 21, 2013 | 1984 AMC American Motors Eagle

2 Answers

I replaced the clutch master cylinder and the braided brake line in a 2000 camaro ss and I'm trying to bleed the system. I know how to do it but I've done the procedure 20 times and there is still no


You may have got a bad master cylinder.It happened to me before.I had to get 3 of them before i got a good one.Mine was on a full size jeep though.

Mar 21, 2013 | Cars & Trucks

1 Answer

So I just changed the clutch master cylinder and the braided brake line in my 2000 camaro ss and am trying to bleed the system. The routine I'm using is typical. Pump the pedal 30 times keep it depres


you have someone helping you right? cuz you cant do it yourself, and the brakes need to be pumped only enough to get a solid midway stop of pedal travel, and with the brake still depressed by your assistant, you open the bleeder a bit until the pedal goes to the floor, you tighten bleeder, they then release brake pedal and pump it up again, rinse, repeat, until there is no spongy feel in brake pedal

Mar 21, 2013 | Cars & Trucks

1 Answer

I'm trying to bleed my clutch in my 2000 camaro ss. I finally found the the bleeder screw at the top of the transmission on the drivers side. Just lookin for some guidance from here forward.


Adam: fill the slave cylinder resivour with fluid attach a bleeder hose to
the port have someone pump the clutch pedal u ntil fluid runs thru
without any air bubbles in it depending on the amount of air in the line
and NO other leaks this may take a few fills.

Jan 30, 2013 | Cars & Trucks

2 Answers

2000 jeep wrangler clutch has to pressure and thus wont allow me to put it in gear.


Check the clutch fluid level. If it's low, add some (takes brake fluid). There is a bleed valve down on the clutch slave cylinder on the bellhousing. Open the bleed valve and have someone push the clutch pedal slowly to floor, and hold. Close the bleed valve, and repeat until fluid comes out in a steady stream when the pedal is depressed. Your pedal should have pressure now, and the clutch should be working.
If no fluid is forced out the clutch master cylinder, into the line, and to the slave cylinder when clutch is pressed, then you may have a bad clutch master cylinder. If fluid does come out the bleed valve, but still no pressure on the pedal, it may be a bad slave cylinder.
Post back for more. Would like to know what you find out, and what the problem was, OB. Good luck.

Jul 13, 2012 | 1991 Jeep Wrangler

1 Answer

1988 camaro 5sp manual, after replacing the master cylinder, bleeding was success, it was only taking 3 months to learn how to bleed it out. Now, when i'm playing burnout, I've lost my pressure on the...


The easiest way to bleed out a clutch hyd system is to connect a hose from the closest front brake caliper bleeder to the bleeder on the slave cylinder. Crack both bleeders open and pump the BRAKE pedal very slowly. It might be best to have someone pump the pedal for you.You will feel the pedal get harder once all the air is pushed out of the clutch system. Close off bleeders and remove hose and test drive car.

This is a back bleed and it's the only way to get all the air out of the clutch system on Peugeots and some other Euro cars.

Feb 28, 2010 | 1988 Chevrolet Camaro

2 Answers

I changed out my slave and master cylinder in a 96 chevy camaro Z28. After doing so pushed down on the clutch to let out all the air bubbles from the new brake fluid. But the cluth is still soft, it has...


put a bar behind the clutch operating arm ,slacken bleed nipple on the slave then pull the bar back so it pushes the slave piston in.tighten bleed then release pressure on the bar ,and repeat a few times this should do it

Nov 20, 2009 | 1996 Chevrolet Camaro

1 Answer

Clutch pedal stays 2 the floor on a hydralic clutch system on a 2000 camaro v8. clutch master cylinder is new also slave cylinder and clutch and pressure plate


Did you bleed the system? When you replace the the master and/or slave cylinder you have to bleed the system just as you would with brakes. There is a bleed screw on the slave cylinder. Open the bleed screw, have a helper depress and hold the clutch pedal down.Tighten the bleed screw, then release clutch. Repeat this procedure until you have removed all air from the system and the clutch pedal is firm. Keep an eye on the fluid level to avoid sucking air into the system. If you have done this, remember there is a possibility that the master or slave cylinder is defective.

Sep 06, 2009 | 2000 Chevrolet Camaro

1 Answer

Clutch not primming in r32 skyline


You either have air in the system or a faulty master cylinder.

Check fluid is being delivered from the master cyl. by slackening off the hydraulic line connection at the master cylinder while depressing pedal.
Until fluid is able to be delivered from the master cyl. itself you have no hope of bleeding the rest of the system.

As with all hydraulic bleeding processes, only release the fluid line when the pedal is being pushed slowly down or held down against the return spring pressure of the clutch pressure plate - re-tighten it on the upward stroke of the pedal to stop it drawing air back into the system.

If you are confident that there is fluid delivery from the master cyl. move to the clutch slave cylinder.

Again only open the bleeder valve when the pedal is being pushed slowly down (i.e. the hydraulic system is pressurised).

(If you keep the master cylinder full of hydraulic fluid, sometimes gravity will cause the line to 'self bleed' if the bleed nipple is left slightly open for several minutes at the start of the bleed process).
When fluid appears, finish the slave cylinder air bleed in the normal way.

If you have the time to spare, I have often found that provided the master cylinder is kept full, leaving the system overnight will allow a lot of the air to leave the system (gravity helps).

May 31, 2009 | 2002 Nissan Altima

1 Answer

1994 chevy camaro 3.4manual 5 speed


You may want to read bleeding instruction at this link, it may shed some light.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800b886d

Jan 31, 2009 | 1994 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...