Question about 2008 Mazda Cx 9

Open Question

I need to replace the Front Hub assembly on a 2009 Mazda CX9. Sere noise coming out from the front end and have been diagnostic by a mechanic as front bearing. Any idea how to remove and re-install them?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 142 Answers

SOURCE: I'm having the same exact problem as cpurdey

If it gets worse as you're turning right, but not left - Most definitely a wheel bearing on the right side. The right turn puts more stress on the right wheel - louder noise - turn left and release the stress - no noise. You can also lift the vehicle up on a jack and listen to the wheel and hear the bearing in the hub making noise.

Posted on Jun 02, 2011

Ad
  • 5 Answers

SOURCE: removal front wheel bearing 2003 mazda protege

hi there, i have 2 mazda6s, both off which i needed to removed the inner axels on, so far you have done every thing right :), but unfortunatly due to mazdas sloppy assembly the inner axles are near impossible to remove, you could try getting a 2 or 3 legged puller and remove the brake calliper and disk then try and "pull" the shaft out, but unfortunatly i doubt will work. your second option would be to use a hydraulic ram to press it out, but again due to mazdas sloppy work it is near impossible with out damaging the hub, ive tryed both option and none of wich worked, so i brought 4 second hand hubs and outer C.Vs, hope this helps.

Posted on Sep 03, 2009

  • 204 Answers

SOURCE: 1998 Mazda 626 LX-When driving, a rubbing noise is

Hope your mechanic is right cos that is a costly job. Try calling around your local parts dealers, aka Autozone, Advance, Oreilly for prices on parts.

Posted on Feb 03, 2010

  • 2 Answers

SOURCE: I have been told my

the bearing and hub are peened as a assembly and will need to be pressed out of hub carrier on early 05. later models use a one piece bearing that will need to have hub pressed out, then bearing pressed out of carrier both bearings are avalable aftermarket

Posted on Nov 08, 2010

  • 85 Answers

SOURCE: I am replacing the left front wheel bearing hub on

When replacing any hub assembly you should never over-tighten the three or four bolts that bolt on the assembly. This will cause it to fail quickly. Use lock-tight to make sure they do not loosen up after installation. A way to tell if your hub assembly is going out is to push and pull on the top of tire. If it wobbles at all it should be replaced. If the hub assembly includes steering components that might interfere with the steering alignment then you should have it re-aligned after installation.

Posted on Nov 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Thumping noise coming from front end


If the noise indeed does get louder when turning right, I would suspect the leftside hub.

Apr 05, 2013 | 2004 Chevrolet TrailBlazer

2 Answers

I'm having the same exact problem as cpurdey with my 2004 Mazda MPV. My mechanic is quite certain it is not the wheel bearing or hub but seems to think it's a bearing in the transmission. Is...


If it gets worse as you're turning right, but not left - Most definitely a wheel bearing on the right side. The right turn puts more stress on the right wheel - louder noise - turn left and release the stress - no noise. You can also lift the vehicle up on a jack and listen to the wheel and hear the bearing in the hub making noise.

Jun 02, 2011 | 2004 Mazda MPV

1 Answer

How do i pull the hub off my 2002 mazda , on drivers side front


REMOVAL & INSTALLATION Except Miata FRONT
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Steering knuckle from the vehicle
    • Inner oil seal from the knuckle
  3. Using Mazda Hub Puller tools 49 G033 102, 49 G033 104 and 49 G033 105, pull the front wheel hub from the knuckle assembly.
  4. Remove or disconnect the following:
    • Bearing inner race from the front wheel hub
    • Retaining ring from within the knuckle
    • Front wheel bearing from the knuckle, using the hub puller tools
    • Brake dust shield
  5. Clean and inspect all parts but do not wash or clean the wheel bearing. The bearing must be replaced. To install:
  6. Using Mazda Press tools 49 G033 107 and 49 H026 103, install a new dust shield cover assembly to the knuckle.
  7. Using the press tools, press a new wheel bearing into the knuckle assembly.
  8. Install or connect the following:
    • Wheel bearing retaining ring
    • New oil seal using Installation tool 49 V001 795
    • Front wheel hub using the Mazda press tools
REAR
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: The wheel bearings are not serviceable. If the bearings are bad, a new hub/bearing assembly must be installed.
  2. Remove or disconnect the following:
    • Rear wheels Fig. 1: Exploded view of the rear wheel hub and bearing assembly (disc brake model shown, drum is similar) 7923mg87.gif

    • Brake drum, if equipped
    • Rear caliper and rotor assembly from the hub, if equipped
    • Hub dust cover
  3. Raise the staked portion of the hub retaining nut with a hammer and chisel.
  4. Remove or disconnect the following:
    • Hub retaining nut and discard it
    • Hub and bearing assembly from the spindle Fig. 2: When installing the new hub nut, be sure to stake it into the notch on the spindle 7923mg86.gif
    To install:
  5. Install or connect the following:
    • Bearing assembly on the spindle. Torque the new nut to 131-173 ft. lbs. (177-235 Nm)
    • Stake the nut into the groove in the spindle
    • Dust cover
    • Assemble the brakes
    • Rear wheel

Jan 01, 2011 | 2002 Mazda Protege

1 Answer

1998 Mazda 626 LX-When driving, a rubbing noise is coming from the front driver side wheel. Was told it was the front wheel hub assembly. Would like to replace bothsides( bearings etc). How do I order...


Hope your mechanic is right cos that is a costly job. Try calling around your local parts dealers, aka Autozone, Advance, Oreilly for prices on parts.

Feb 03, 2010 | 1998 Mazda 626

2 Answers

1993 buick park ave wining noise from front end


Grinding noise in the front end could be your bearings or you cv joint

Jan 29, 2010 | 1993 Buick Park Avenue

1 Answer

Noise coming from the front end while your on the highway then goes away when you turn to the right


More then likely you have a bad front hub bearing assembly.Noise goes away when turn right less pressure on right wheel bad right front bearing.

Jan 19, 2010 | 2001 Mazda Tribute

2 Answers

Clicking noise in front end 2001 dodge ram 4x4


the ansew i found is replacing the seal around the joint and from both end removing it and cleaning it out i had rocks in mine from going threw water and mud ita a all day deal but a twenty doller fix axle shaft oil seal is all i had to replace

Apr 05, 2009 | 1997 Dodge Ram 1500 Club Cab

2 Answers

1995 Toyota Celica Front Wheel Hub


can u replace the bearing in the hub? will that fix your problem?

May 25, 2008 | 1995 Toyota Celica

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

139 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8499 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...