Question about 2000 Chevrolet Silverado 1500

1 Answer

I am having an instrument cluster light issue......replaced all bulbs and checked all fuses and still no luck.....any help is appreciated

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 3,187 Answers

Check the main light switch control there is a dimmer control on/or inside it can fail.i am having an instrument cluster light - b9a9b50b-6bad-4432-b6aa-e83f483dd33a.jpgthis controls light and dash lights. dimer on the right.

Posted on Oct 16, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

SOURCE: Tail lights don't work on 1998 Chevy Silverado.

check the wiring from the tailights back to the fuse panel, it sounds like an open connection. if i recall correctly check under the dash on the drivers side near the fuse panel for a bunch of wires in a bundle and look carefully for a wire or two that are cut/shorted/or seperated, you can also check under the drivers side kick panel by the hood release.

Posted on Feb 17, 2009

  • 1 Answer

SOURCE: instrument panel cluster gauges and odometer has stopped working

I had all my analog instrument panel gauges stop working after they did the state emissions test. I found the proper fuse in the fuse block located under the hood. Simply unplugged the fuse, noticed it was still good, and plugged the same fuse (10A) back in and all the gauges started working again. Guess it needed a reset atfer they plugged in for the emissions.

Posted on Aug 14, 2009

oldmanewtoys
  • 414 Answers

SOURCE: 99 chevy silverado dashboard lights flicker on and

Check for a complete ground small strap near radio

Posted on Mar 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Instrument cluster lights don't light up on my 1993 Lincoln town car cartier model


If the problem is not a fuse the lighting pannel might be burned out.

Sep 15, 2014 | 1993 Lincoln Town Car

1 Answer

The lights for my speedo, clock, temp gauge and fuel gauge not working, indicators, main beam, high beam, oddometer, handbrake, foglight all working ok?


You should have a fuse in the fusebox for the instrument cluster. The instrument cluster houses your gauges, speedometer, clock, and temperature gauge or light. Check the fuse to see if it blown and replace with the same size number on the fuse. Don't decrease or increase the number of the fuse. Stay with the same amp number that is on the old fuse when you replace it. Hope this helps.Good luck.

Mar 07, 2014 | Cars & Trucks

1 Answer

Honda civic instrument panel lights out


  1. Use a test lead with a indicator light / led to trace power to instrument cluster lights.
  2. A circuit diagram would be of assistance if you are competent to read the circuitry and symbols.

Mar 05, 2014 | Cars & Trucks

1 Answer

I have a 1997 cavalier z24 that is having some electrical problems. The tail lights, side marker lights, and instrument cluster lights do not work. I've already replaced the fuse, but it keeps...


you have a dead short immediately after the fuse Check wiring for rub points/ pinch points. Check all bulb sockets to ensure that the power wire is not touching earth or the earth wire.

Jun 13, 2013 | Cars & Trucks

2 Answers

NO LIGHTS ON LEFT SIDE OF ODOMETER PANEL - FUSE OR MAJOR WORK?


fuse ok.need to remove instrument cluster and see if good connection on the cluster os maybe yo can see a break in plastic circut board.I would have another instrument cluster handy if old unit not repairable

Feb 12, 2011 | 2001 Toyota Camry Solara

1 Answer

Instrument cluster lights don't work. Fuses and bulbs are good.


feed wire for the lights may have failed or the circuit on the board may have gone. if you remove the cluster you can put a supply to the bulb circuit (carefully) and check if it is the circuit. If it's ok you can run a new feed to the cluster from your lights. Job done.

Feb 16, 2010 | 1995 Jeep Cherokee

1 Answer

Instrument cluster bulb is out. how do i replace


It may not be a bulb, as the instrument cluster usually has a number of bulbs and they probably didn't all blow at once. Pulling instrument clusters can be touchy and may not be for the average "shadetree mechanic" however, typically there are a few screws above the cluster going into the dash pad and a few hidden behind the trim panels below the cluster.

Dec 22, 2009 | 2001 Chrysler Sebring

2 Answers

Check engine light does not turn on at all


The bulb is probably loose and/or burnt out. If you are mechanically inclined you can tackle this job... This procedure is the one i use, most often it's the blue high beam indicator bulb that goes so if you want to change it while your in there.....(hint hint)
Disconnect and isolate the battery negative cable. Wait a good 2 minutes to allow for air bag deactivation...NOTE: USE CAUTION ...Lower the tilt wheel to lowest position.
Remove the cluster bezel from the instrument panel.
Remove the two screws that secure the upper mounting tabs of the instrument cluster to the underside of the instrument cluster hood formation of the instrument panel top pad.
Remove the two screws that secure the lower mounting tabs of the instrument cluster to the instrument panel structural duct.
Pull the upper mounting tabs of the instrument cluster downward, then pull the instrument cluster rearward far enough to access the instrument panel wire harness connector for the instrument cluster. Disconnect the instrument panel wire harness connector for the instrument cluster from the connector receptacle on the back of the instrument cluster housing.
Remove the instrument cluster from the instrument panel. Now do you remember which bulb it was? You can now see where the check engine light bulb is mounted. Twist and remove, install in reverse order. In some cases they are just loose or not making good ground, but after going through this just to access that lil bugger, i'd replace it.
I hope i have helped you and if you feel i have please acknowledge.
Be well and keep the cherokees alive....

May 13, 2009 | 2001 Jeep Cherokee

1 Answer

Instrument cluster illumination has failed. Grand Voyager 2002


I would start with checking all the fuses. There sould be multaple bulbs in the cluster . there for if all the lights are out it is unlikely a bulb. Make sure you check ALL fuses . Let me know if this helps

James

Jul 19, 2008 | 2002 Chrysler Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

149 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...