Question about Chevrolet Monte Carlo

1 Answer

I replaced the tumber and key in my 2002 s10 le 4x4 with one from a 2002 s10 2wd,im 4x4 has a 4.3L and automatic,while the 2wd is a 2.2L and a standard,now it wont start

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 29 Answers

If you replaced the ignition cylinder housing as well the passlock system will have to be relearned. Hook some sort of battery charger or stabilizer. attempt to start the vehicle and just release the key to the running position....check security/theft light on or flashing. after about 10 minutes the security/theft light should go off, turn key off but dont remove for 5 seconds, then attempt to start again. Do this 3 times for a total of roughly 30 minutes and it should start.

Posted on Oct 16, 2013

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

longbow243
  • 103 Answers

SOURCE: keyless entry wont work 2002 chevy s10

The only way to program them is with a scan tool so you'll need to visit your local dealer to have it done. Here is how it is done.

  1. Install a scan tool.
  2. Use the scan tool in order to access programming: Vehicle Control System/Computer Integrating System/Module Setup/BCM/Program Key Fobs.
  3. Press the START soft key on the scan tool. Important: The scan tool must stay connected until all of the transmitters are programmed.
  4. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of 5-10 seconds, the scan tool will indicate that the transmitter is programmed.
  5. Repeat the previous step in order to program up to 4 transmitters.
  6. Remove the scan tool.
  7. Operate the transmitter functions in order to verify correct system operation.

Posted on Sep 03, 2009

Testimonial: "thanks man, wasnt sure but i thought i had to take it to a dealer.. everyone else told me i could do it myself.. thanks again keith...."

sledge1863
  • 149 Answers

SOURCE: 1999 s10 stater

There is a fuseable link in the wire that attaches to the starter solenoid. It will be on the smaller wire, a large plastic piece. Replacements can be found at auto parts store. Good luck, dont forget to rate.

Posted on Jan 11, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1995 S10 4,3l runs too rich. What can be faulty?


That truck was known for the spider injector under the intake. Not hard to replace. Upper Intake comes out as 1 assembly. You usually get a smell of rotten eggs when it fails. After replacement run SEAFOAM in gas ( and oil ) to clean out Carbon, fuel system and CAT

Nov 20, 2013 | Chevrolet Blazer Cars & Trucks

1 Answer

Where do i fill transimision fliud 2005 malibu classic 2,2l automatic


Pull out the dip stick for the transmission, use a transmission funnel and pour in the transmission fluid.

Mar 18, 2011 | 2005 Chevrolet Malibu

2 Answers

Starter locked and steering wheel wont move.


have you tried pulling the steering wheel to either side as you turn the key and then wiggling the steering wheel back and forth

Jul 05, 2010 | 1997 Mercury Mountaineer

1 Answer

1997 chevy s10 blazerdash wont light up when key


the dash sound's like a fuse, check the fuse box under the hood and in the door jamb on the side of the dash, also check your fuel filter and fuel pump, im betting on the pump because i have a 2001 chevy blazer that has had two replaced and it has 233000km on it!

Jun 04, 2010 | 1997 Chevrolet Blazer

1 Answer

Will a 2001 4.3 fit a 95 4.3 I have a 2001 Rolled s10 blazer w a 4.3 and an automatic trans will this fit and work in a 1995 s10 blazer that had a 4.3 and an automatic transmission


Yes it will but your going to have to also transplant the ECM. The change off years to the Blazers are 1992 to 1995 and interchangeable, 1995 being the odd ball year for the 4.3, and in 1996 to 2002 are all drive-train interchangeable. Good luck and keep me posted if you have any more questions.

Feb 22, 2010 | 2001 Chevrolet Blazer

1 Answer

Breack d'ont works bulls all are ok fus ok !! i check inside of swictcht ok on my chevrolet s10 v6 4,3l auto 1997 thks GEORGES jobymib501@hotmail.com or do you have the shema of the wiring or the...


I fixya thanks for reply i just check on the switch inside they no contact betewen the lamell !!! everyting was ok fus bulls cabls just the probleme was inside the switch  is ezy to open by your self  L G

Jan 30, 2010 | 1998 Chevrolet S-10 Pickup

1 Answer

My ford windstar's ignition will not turn to the on position. it appears to be stuck


Try spraying wd40 or some king of lubricant in the key cylinder. Dirt has gotten into the tumber and causing the pins inside to stick. If you get it unstuck either leave the key in and do not turn to lock position or replace the tumbler. I hope this helps. good luck.

Aug 02, 2009 | 2002 Ford Windstar Cargo

1 Answer

Keyless entry wont work 2002 chevy s10 LS


try this procedure to reporgram:

1. Close all vehicle doors.

2. Insert the key into the ignition.

3. Hold down the power UNLOCK button on the driver's continue to hold down until instructed
to release in step 9.

4. Perform steps 5 through 8 in fairly rapid succession.

5. Turn the key to the ON position (as far as you can go without starting the engine).

6. Turn the ignition switch to the OFF position.

7. Turn the ignition switch to the ON position.

8. Turn the ignition switch to the OFF position.

9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.

10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the vehicle locks and unlocks.
This step may take up to 30 seconds.

11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).

12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode

Jun 30, 2009 | 2002 Chevrolet S-10

1 Answer

Pcv location on 2002 s10


it is a tube connected to the valve cover. So there really isn't a valve.

May 15, 2009 | 2002 Chevrolet S-10

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...