2006 c5500 4x4 4 door rear bearing rachet nut torque

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow

2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...

Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..

taper bearings if i remember right so a slight pull will suffice.unless its has rear disks with a roller bearings ,in which case tighten up with a rachet which will give you around 40lbs then use a strong arm bar and give it a light tug ,,sorted job done .

Front wheel bearing torque is usually about one uga dugga.

You do not back off the torque, which is likely about 150 ft pounds.

Hi Connie,just read your forum,here's a link to your rear hub bearing nut torque specs. http://www.autozone.com/repairinfo/repairguide/repairGuideContent.jsp?pageId=0996b43f802d649d

Three bolts are 70 lbs,could be 120+/-.

4-Wheel Drive

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear wheel
     
   • Rear brake shoes
     
   • Rear halfshaft nut and loosen the halfshaft from the hub
     
   • Wheel hub and place it in a vise
     
   • Inner wheel bearing race from the hub
     
   • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
     
   • Parking brake cable from the steering knuckle
     
   • Brake line from the wheel cylinder and support the knuckle
     
   • Lower shock absorber nut
     
   • Lower ball joint by holding the ball joint stud
     
   • Upper ball joint
     
   • Coil spring while noting the location of the insulator
     
   • Steering knuckle cam
     
   • Steering knuckle
     
   • Snapring and press out the outer wheel bearing race from the knuckle
     

     Rear hub and bearing
     Click to Enlarge

To install:

1. Install or connect the following:
   
   • New wheel bearing into the steering knuckle
     
   • Snapring to the knuckle
     
   • Wheel hub
     
   • Steering knuckle cam and hand tighten the bolt
     
   • Coil spring
     
   • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
     
   • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
     
   • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
     
   • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
     
   • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
     
   • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
     
   • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
     
   • Brake shoes
     
   • Rear wheel
     
   • Negative battery cable
     
2. Fill and bleed the brake system.
   
3. Check and adjust the wheel alignment as needed.
   

2-Wheel Drive

1. Before servicing the vehicle, refer to the Precautions Section.
   
2. Remove or disconnect the following:
   
   • Negative battery cable
     
   • Rear wheel
     
   • Rear brake drum
     
   • Wheel hub nut
     
   • Wheel hub
     
   • Inner wheel bearing race from the hub
     
   • Snapring
     
   • Wheel bearing outer race from the knuckle
     

     Rear hub and bearing
     Click to Enlarge

     Rear hub removal
     

     Inner wheel bearing removal-rear hub/bearing
     

     Rear wheel bearing removal-2wd
     

     Rear wheel bearing removal-4wd
     

To install:
Install or connect the following:

• Wheel bearing in to the knuckle
  
• Snapring
  
• Wheel hub into the wheel bearing
  
• Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  
• Brake drum
  
• Rear wheel
  
• Negative battery cable
  

  Rear wheel bearing installation
  
  hope this helps if so send testimonial comment or even any other questions you have
  

Hello, here is the torque spec for front hub bearing
Strut to Steering Knuckle Bolt and Nut
180 N·m
133 lb ft
Tie Rod Retention Nut
50 N·m
37 lb ft
Wheel Bearing/Hub Mounting Bolt
130 N·m
96 lb ft
Wheel Drive Shaft Spindle Nut
205 N·m
157 lb ft

drum brakes you remove rear wheel- speed sensor-grease cap-flange nut-outer bearing-brake drum-inner grease seal-inner bearing-drive the bearing races out of the drum hub.to install -install the inner and outer bearing races.apply grease to the bearings and hub cavity.then you install the inner bearing -inner grease seal-brake drum-outer bearing-flange nut torque it to 159 to 192 ft lbs. THE REAR DISC BRAKE WHEEL BEARINGS-you have to remove rear wheel -wheel speed sensor-brake caliper and rotor-rear axle hub bolts-tone the wheel with tool 09445-21000-carrier assembly-nut after unstaking it-press out the rear axle hub-remove the bearing inner race with tool 09445-21000-remove the bushings from the carrier with tools 09453-33000b and 09545-21100.to install -press in the bushings to the carrier with tools 09453-33000b and 09545-21100- press in the bearings to the hub with tool 09221-21000.tighten the flange nut to meet the concave portion of the spindle-press in the tone wheel with tool 09221-21000-torque the nut to 191 ft lbs -install the hub and bearing assembly to the backing plate and torque the bolts to 88 ft lbs-install the brake caliper and rotor.install the wheel speed sensor if equipped.install the rear wheel.TO BUY THE TOOLS TO DO THE JOB.LOOK UP KENT MOORE TOOLS ON INTERNET.

Axle Preload and Backlash Specifications 8.0 Axle Preload and Backlash Specifications Application
Specification
Metric
English
Backlash
0.08-0.25 mm
0.003-0.010 in
Backlash (Preferred)
0.13-0.18 mm
0.005-0.007 in
Pinion Bearing Preload, New Bearings
1.7-3.4 N·m
15-30 lb in
Pinion Bearing Preload, Used Bearings
1.1-2.3 N·m
10-20 lb in
Pinion and Differential Case Bearing Preload, New Bearings
3.4-6.2 N·m
30-55 lb in
Pinion and Differential Case Bearing Preload, Used Bearings
2.8-5.1 N·m
25-45 lb in