Question about Toyota Avanza

Open Question

K3ve timing mark Timing chain

K3ve timing mark Timing chain

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 512 Answers

SOURCE: 3.3l dodge caravan, where to set timing chain marks

the top gear timing mark points at 6oclock...crank gear at 12 oclock

Posted on Sep 27, 2008

Ad
psds4
  • 293 Answers

SOURCE: timing marks,cam and crank,2.4l

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528018d02c

Posted on Oct 09, 2008

motor1258
  • 6674 Answers

SOURCE: timing marks for chryster sibring 2003 2.7L

Here's a link to 98' - 2004 Intrepid 2.7. If you have dual cam etc. and all looks same, you should be o.k. Take a real good look at picture. If you click on it when you get there, it expands.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152801d4ab5


Posted on Dec 22, 2008

  • 12 Answers

SOURCE: timing chain mark diagram for a 94 grand am????

would your engine be a 2.4 quad ??

Posted on Apr 15, 2009

kennyz195
  • 61 Answers

SOURCE: 1999 Ford Expedition 5.4L Timing chain setup

.

  1. Remove the engine front cover. For additional information, refer to Engine Front Cover in this section.
  1. Remove the crankshaft sensor ring from the crankshaft.
    a0044041.gif
  1. Rotate the crankshaft until the timing mark on the RH camshaft sprocket is approximately at the 11 o'clock position and the timing mark on the LH camshaft sprocket is approximately at the 12 o'clock position.
    a0049532.gif
  1. Using the special tool, position the crankshaft as shown.
    a0041102.gif
  1. Install the special tool.
    aa5423a.gif
  1. NOTE: LH shown; RH similar.
    Remove the two bolts, the timing chain tensioner and tensioner arm.
    aa5952a.gif
  1. Remove the LH and RH timing chains and the crankshaft sprockets.
    • Remove the special tool from the crankshaft.
    • Remove the timing chains from the camshaft sprockets.
    • Remove the right and left timing chains and the crankshaft sprocket from the crankshaft.
    a0029151.gif
  1. ani_caut.gif CAUTION: The bolts are different lengths and must be returned to their original location.
    NOTE: LH shown; RH similar.
    Remove the bolts and the timing chain guides.
    a0044040.gif
Installation
  1. ani_caut.gif CAUTION: Timing chain procedures must be followed exactly or damage to valves and pistons will result.
    ani_caut.gif CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
    Compress the tensioner plunger, using an edge of a vise.
    da0605a.gif
  1. Using a small screwdriver or pick, push back and hold the ratchet mechanism.
    da0606a.gif
  1. While holding the ratchet mechanism, push the ratchet arm back into the tensioner housing.
    da0607a.gif
  1. Install a paper clip into the hole in the tensioner housing to hold the ratchet assembly and plunger in during installation.
    a26917a.gif
  1. Remove the tensioner from the vise.
  1. NOTE: There are 61 links in the timing chain.
    If the copper links are not visible, mark two links on one end and one link on the other end, and use as timing marks.
    a0038720.gif
  1. Install the timing chain guides.
    a0044063.gif
  1. Using the special tool, verify correct crankshaft position.
    • Remove the special tool.
    a0041102.gif
  1. NOTE: Crankshaft sprockets are identical. They can only be installed one way. Refer to the following illustration for correct crankshaft sprocket installation.
    If removed, install LH and RH crankshaft sprockets.
    a14824b.gif
  1. Install the LH timing chain onto the crankshaft sprocket, aligning the one copper (marked) link on the timing chain with the slot on the crankshaft sprocket.
    a0041197.gif
  1. Position the LH timing chain on the camshaft sprocket with the two copper (marked) chain links and the camshaft sprocket timing mark aligned.
    a0049191.gif
  1. Position the RH (outer) timing chain on the crankshaft sprocket, aligning the copper (marked) link with the timing mark on the sprocket.
    a0041196.gif
  1. Position the RH timing chain on the camshaft sprocket. Make sure the two copper (marked) links align with the camshaft sprocket timing mark.
    a0041104.gif
  1. NOTE: LH shown; RH similar.
    Position the tensioner arms and tensioners, and install the bolts.
    aa5952a.gif
  1. Remove the tensioner retaining clip.
    a26273a.gif
  1. As a post-check, verify correct alignment of all timing marks.
    a0041106.gif
  1. Remove the special tool.
    aa5423a.gif
  1. Position the crankshaft sensor ring on the crankshaft.
    a0044041.gif
  1. Install the engine front cover. For additional information, refer to Engine Front Cover in this section.


2010&c18=modelyear&c20=n310677&c35=wsm%2ctiming%20drive%20components%2csxj%2c303-01b%2cin-vehicle%20repair&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Posted on Apr 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you adjust valves on a 2006 3.5L V6 Toyota Avalon?


There is a Toyota Technical Service Bulletin issued for this:-
T-SB-0291-08 September 11, 2008 2GR-FE Valve Timing

Procedure Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 - 2009 Avalon 2007 - 2009 Camry VDS(s): BK46K 2008 - 2009 Highlander 2006 - 2009 RAV4 Engine(s): 2GR VDS(s): BK31V, BK32V, BK33V, BK34V, ZK31V, ZK32V, ZK33V, ZK34V, ZK35V 2007 - 2009 Sienna Introduction This service bulletin provides information regarding valve timing inspection and service guidelines for vehicles equipped with 2GR-FE engines. © 2008 Toyota Motor Sales, USA Page 1 of 5 T-SB-0291-08 September 11, 2008 Page 2 of 5 2GR-FE Valve Timing Procedure Introduction (Continued) Figure 1. 3 2 1 5 9 8 7 6 4 1 RH Bank Intake Camshaft Timing Gear 2 RH Bank Exhaust Camshaft Timing Gear 3 RH Bank No. 2 Timing Chain 4 Crankshaft 5 Idler Gear 6 Timing Chain 7 LH Bank No. 2 Timing Chain 8 LH Bank Exhaust Camshaft Timing Gear 9 LH Bank Intake Camshaft Timing Gear Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 3 of 5 2GR-FE Valve Timing Procedure Inspection 1. Set the No. 1 cylinder to TDC/compression. A. Set the timing mark to 0 on the timing chain cover by rotating the crankshaft clockwise. B. Verify the timing marks on the camshaft timing gears are in general alignment with the timing marks of the camshaft bearing cap: TIMING MARK IDENTIFICATION CYLINDER BANK INTAKE GEAR MARK EXHAUST GEAR MARK RH Bank (Bank 1) Small Mark Single Line LH Bank (Bank 2) Large Mark Double Line HINT When the engine is correctly timed, the timing marks will NOT perfectly align. Figure 2. Figure 3. RH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 4. RH Bank Intake Camshaft Timing Gear 2 1 1 Bearing Cap Timing Mark 2 Gear Timing Mark © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 4 of 5 2GR-FE Valve Timing Procedure Inspection (Continued) Figure 5. LH Bank Intake Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 6. LH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark HINT If the timing marks appear vastly out of alignment, turn the crankshaft one revolution (360 ) clockwise and note the position of the timing marks. Component Removal Guidelines 1. If engine disassembly is required that involves removing the camshafts or timing gears, set the #1 cylinder to TDC compression, wipe away any oil, and mark the following items in relation to each other prior to disassembly: • Timing gears • Timing chain • Timing chain No. 2 NOTE This relationship MUST be maintained. The intake gear is timed in relation to the crankshaft via the timing chain; the exhaust gear is timed in relation to the intake gear via the No. 2 timing chain. © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 5 of 5 2GR-FE Valve Timing Procedure Component Removal Guidelines (Continued) 2. If NEW camshaft timing gears or the No. 2 timing chain are being installed, the two yellow links on the No. 2 timing chain can be used to ensure correct relationship between the intake timing gear and the exhaust timing gear. Figure 7. 1 1 Yellow Link A. Align the paint mark on the timing chain with the intake gear timing mark (to ensure the intake gear is correctly timed to the crankshaft). Figure 8. RH Bank and LH Bank 3 3 4 3 3 4 5 4 5 4 1 2 1 RH Bank 2 LH Bank 3 Yellow Link 4 Gear Timing Mark 5 Timing Chain Paint Mark B. Align the two yellow links on the No. 2 timing chain to the timing marks on

May 04, 2015 | 2006 Toyota Avalon XLS

1 Answer

How do I set timing on a 2.3 Suzuki aerio engine


wow no job stated.
04 (2.3L) ill take a wild guess and say, you might be fiddling the cam
and doing something there, new cam, new lifters, new chain, new head, ? what?
FSM means factory service manual, ever heard of one?

the FSM is just lousy 4 bucks why not read that first. and not mess it up.

https://suzukipitstopplus.com/Products/1004-2004-aerio-service-manual.aspx

you said SET, so i can only assume its all apart. right then
you want to Instal the chain and time it, right so here are the fsm steps
no photos. log in and read the FSM for that.
  1. Check that match mark on crankshaft timing sprocket is in match with timing mark on lower crankcase.
  2. Install crankshaft timing sprocket as shown in figure.
  3. Apply oil to bush of idler sprocket and install idler sprocket and sprocket shaft.
  4. Install first timing chain by aligning dark blue plate of first timing chain and match mark on idler sprocket.
  5. Bring yellow plate of first timing chain into match with match mark on crankshaft timing sprocket.
  6. Apply engine oil to sliding surface of timing chain tensioner and then install it as shown in figure. Tighten tensioner nut to 18 ft. lbs. (25 Nm).
  7. With latch of tensioner adjuster No.1 returned and plunger pushed back into body, insert stopper into latch and body. After inserting it, check to make sure that plunger will not come out.
  8. Install timing chain tensioner adjuster No.1. Tighten the timing chain tensioner adjuster No. 1 bolt to 8 ft. lbs. (11 Nm).
  9. Pull out stopper from adjuster No.1.
  10. Apply engine oil to sliding surface of timing chain guide No.1 and then install it. Tighten guide bolts to 6.5 ft. lbs. (9 Nm).
  11. Check that dark blue and yellow plates of first timing chain are in match with match marks on sprockets respectively.
  12. Install second timing chain as follows:
    • Check that match mark on crank timing sprocket is in match with timing mark on lower crankcase.
    • Check that arrow mark on idler sprocket faces upward.
    • Check that knock pins of intake and exhaust camshafts are aligned with timing marks on cylinder head.
    • Install second timing chain by aligning yellow plate of second timing chain and match marks on idler sprocket.
    • Install sprockets to intake and exhaust camshafts by aligning dark blue plate of second timing chain, match marks on intake sprocket and exhaust sprocket respectively. NOTE As an arrow mark is provided on both sides, camshaft timing sprocket has no specific installation direction.



  • Install intake and exhaust camshaft timing sprocket bolts. To install it, fit a spanner to hexagonal part at the center of camshaft to hold it stationary. Tighten the camshaft timing sprocket bolt to 57.5 ft. lbs. (80 Nm).
  • Push back plunger into tensioner body and hold it at the position by inserting stopper into body.
  • Install timing chain tensioner adjuster No.2 with new gasket. Tighten the timing chain tensioner adjuster No. 2 bolts to 8 ft. lbs. (11 Nm) and No. 2 nut to 33 ft. lbs. (45 Nm).
  • Pull out stopper from timing chain tensioner adjuster No.2.
  • Turn crankshaft two rotations clockwise then align timing mark on crankshaft and timing mark on cylinder block.
  • Check that timing marks of cylinder head and cylinder block are in match with match marks on sprockets respectively.
  • Apply oil to timing chains, tensioner, tensioner adjusters, sprockets, and guides.
  • Install timing chain cover. Reverse removal sequence to install timing chain cover noting the following points:
    • Apply sealant "A" and "B" to area as shown.
      • "A": Sealant 99000-31250
      • "B": Sealant 99000-31140
    • Apply sealant amount to the following areas.
      • "a": 0.12 inches (3mm)
      • "b": 0.08 inches (2mm)
      • "c": 0.24 inches (6mm)
      • "d": 0.63 inches (16mm)
      • "e": 0.55 inches (14mm)
      • "f": 2.56 inches (65mm)
      • "g": 2.87 inches (73mm)
      • "h": 0.16 inches (4mm)
    • Apply engine oil to oil seal lip, then install timing chain cover. Tighten bolts and nut to 8 ft. lbs. (11 Nm).
      NOTE Before installing timing chain cover, check that pin is securely fitted.
    • Before installing timing chain cover, check that pin is securely fitted.
  • Install alternator belt idler pulley. Tighten nut to 30.5 ft. lbs. (42 Nm).
  • Install alternator belt tensioner. Tighten bolts to 18.5 ft. lbs. (25 Nm).
  • Install water pump pulley.
  • Install A/C compressor bracket (if equipped). Tighten bracket bolts to 40 ft. lbs. (55 Nm).
  • Install cylinder head cover with new gaskets and seal washers and tighten nuts to 8 ft. lbs. (11 Nm).
  • Install oil pan.
  • Install crankshaft pulley using pulley holder tool. Tighten the crankshaft pulley bolt to 108.5 ft. lbs. (150 Nm).
  • Install engine assembly.
  • Install all remaining components in the reverse order of the removal procedure.
did that cover it, surely not.
but if you get the FSM and read it or log in , you will not miss the photos and the complex sealing bs on this motor.

Oct 18, 2014 | 2004 Suzuki Aerio

1 Answer

I need a picture of the timing marks for Jeep 4.0


Timing the Cam to the Crank

There are several ways to time the cam to the crank. Be sure to check the manual before you install the timing chain or belt.

  • Some timing sprockets are properly timed when the marks face each other.
  • On others, there must be a certain number of chain links between the marks.
  • Sometimes chains have colored links that must be aligned with the marks on the sprockets.
  • Some overhead cams have a mark on the cam gear that lines up with a mark on the cylinder head when the timing mark on the damper is at the TDC mark.
Align the timing marks for the camshaft and crankshaft sprockets before removing the timing belt or chain.

If the old parts are available, carefully compare the new gears or sprockets with the old ones. Check the keyway and timing marks just in case there might have been an error made in manufacturing. Sprockets are sometimes stamped backward. Its much better to find the problem during assembly, rather than waiting until problems show up after reassembly and reinstallation.

Maintaining Valve Timing

During a valve job, it is essential to keep the timing chain or belt in place to maintain correct valve timing. Position the number one cylinder at TDC. Some overhead cam engines use a single long chain for a cam drive. The chain can be wedged against its guides with a tapered block of wood.
the chain tensioner on some ohc engines must be wedged to keep the chain in position during cylinder head removal. courtesy of nissan motors.

Some engines have a lower and upper chain. These engines do not require special attention to wedging the chain. Be sure to look for hidden head bolts and check the repair manual before removing the OHC head.

Dec 07, 2012 | 1989 Jeep Cherokee

1 Answer

Needing a timingbelt diagram 1997 Altima Nissan GXE L4-2.4L


  • It's a timing chain not a belt.

  • This diagram shows how to position the lower timing chain so that the mating marks line up.


11_25_2011_1_46_21_am.jpg

  • Lower timing chain tensioner and timing chain guide positioning.

11_25_2011_1_48_38_am.jpg
Double check the mating mark alignment of the upper timing chain and idler sprocket.

11_25_2011_1_50_07_am.jpg
  • Make sure that the upper timing chain and camshaft sprocket mating marks align.


11_25_2011_1_51_12_am.jpg

  • There are the diagrams you requested.
  • Hope this helps...



Nov 25, 2011 | Cars & Trucks

1 Answer

1997 Nissan-Datsun Altima GXE L4-2.4L timingbelt diagram


  • It's a timing chain not a belt.

  • This diagram shows how to position the lower timing chain so that the mating marks line up.


11_25_2011_1_46_21_am.jpg

  • Lower timing chain tensioner and timing chain guide positioning.

11_25_2011_1_48_38_am.jpg
Double check the mating mark alignment of the upper timing chain and idler sprocket.

11_25_2011_1_50_07_am.jpg
  • Make sure that the upper timing chain and camshaft sprocket mating marks align.


11_25_2011_1_51_12_am.jpg

  • There are the diagrams you requested.
  • Hope this help.

Nov 25, 2011 | Cars & Trucks

1 Answer

2005 f250 5.4 gas need to know specs for timing a diagram would be awesome


To Install:
  1. Install balance shaft drive gear onto the left camshaft.
  2. Install the camshaft sprockets and new bolts finger tight.
  3. Using a vise, compress the timing chain tensioner plunger.
  4. Install a retaining clip on the tensioner to hold plunger IN during installation.
    marking timing chain a0038720.gif

  5. If timing chain copper links are not visible, mark 2 links on one end and 1 link on the other end to be used as timing marks.
  6. Install right and left timing chain guides. Tighten bolts to 89 in-lbs (10 Nm).
  7. Rotate the left camshaft until the timing mark is at the 12 o'clock position.
  8. Rotate the right camshaft until the timing mark is at the 11 o'clock position.
  9. Position the crankshaft using the special tool. Then remove the tool.
    Crankshaft special tool positioning n0013602.gif

  10. Install the crankshaft sprocket with flange facing forward.
    Crankshaft sprocket timing mark n0011528.gif

  11. Position lower end of left (inner) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley. NOTE: Upper half of timing chain must be below the tensioner arm dowel.
  12. Position the left timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
    Left camshaft sprocket timing mark a0080774.gif

  13. Place the left timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm). NOTE: Lower half of timing chain must be above the tensioner arm dowel.
    Crankshaft sprocket timing mark a0079624.gif
  14. Position lower end of right (outer) timing chain on the crankshaft sprocket. Align the copper (or marked) chain link with the timing mark on the outer flange of the crankshaft pulley.
    Right camshaft sprocket timing mark a0041104.gif

  15. Position the right timing chain on the camshaft sprocket. The timing mark on the camshaft sprocket must be aligned between the 2 copper (or marked) chain links.
  16. Place the right timing chain tensioner arm on the dowel pin and install the timing chain tensioner and bolts. Tighten bolts to 18 ft-lbs (25 Nm).
  17. Remove the retaining clips from the right and left timing chain tensioners.
  18. Verify alignment of all timing marks.
  19. Install crankshaft sensor ring on crankshaft.
  20. Locate index mark on balance shaft and mark corresponding gear tooth with chalk.
  21. Position balance shaft on journals. NOTE: It may be helpful to use an inspection mirror to view the marks timing marks.
  22. Align the chalk mark on the balance shaft with the camshaft timing mark.
    Balance shaft bearing caps n0007112.gif

  23. Install the balance shaft bearing caps in their original locations. Follow the tightening sequence as shown in the illustration. Tighten bolts to 89 in-lbs (10 Nm).
  24. Tighten the camshaft phaser sprocket bolts in the correct sequence using 2 steps, as follows:
    • Step 1-30 ft-lbs (40 Nm)
    • Step 2-tighten an additional 90 degrees
  25. Position the crankshaft keyway in the 11 o'clock position.
  26. Lubricate and install all camshaft roller followers. WARNING
    Engine front cover replacement procedure must be completed within 4 minutes or entire procedure must be repeated. Failure to do so may result in future leaks

Oct 07, 2010 | Ford F-250 Cars & Trucks

1 Answer

1999 Ford Expedition 5.4L Timing chain setup


.
  1. Remove the engine front cover. For additional information, refer to Engine Front Cover in this section.
  1. Remove the crankshaft sensor ring from the crankshaft.
    a0044041.gif
  1. Rotate the crankshaft until the timing mark on the RH camshaft sprocket is approximately at the 11 o'clock position and the timing mark on the LH camshaft sprocket is approximately at the 12 o'clock position.
    a0049532.gif
  1. Using the special tool, position the crankshaft as shown.
    a0041102.gif
  1. Install the special tool.
    aa5423a.gif
  1. NOTE: LH shown; RH similar.
    Remove the two bolts, the timing chain tensioner and tensioner arm.
    aa5952a.gif
  1. Remove the LH and RH timing chains and the crankshaft sprockets.
    • Remove the special tool from the crankshaft.
    • Remove the timing chains from the camshaft sprockets.
    • Remove the right and left timing chains and the crankshaft sprocket from the crankshaft.
    a0029151.gif
  1. ani_caut.gif CAUTION: The bolts are different lengths and must be returned to their original location.
    NOTE: LH shown; RH similar.
    Remove the bolts and the timing chain guides.
    a0044040.gif
Installation
  1. ani_caut.gif CAUTION: Timing chain procedures must be followed exactly or damage to valves and pistons will result.
    ani_caut.gif CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
    Compress the tensioner plunger, using an edge of a vise.
    da0605a.gif
  1. Using a small screwdriver or pick, push back and hold the ratchet mechanism.
    da0606a.gif
  1. While holding the ratchet mechanism, push the ratchet arm back into the tensioner housing.
    da0607a.gif
  1. Install a paper clip into the hole in the tensioner housing to hold the ratchet assembly and plunger in during installation.
    a26917a.gif
  1. Remove the tensioner from the vise.
  1. NOTE: There are 61 links in the timing chain.
    If the copper links are not visible, mark two links on one end and one link on the other end, and use as timing marks.
    a0038720.gif
  1. Install the timing chain guides.
    a0044063.gif
  1. Using the special tool, verify correct crankshaft position.
    • Remove the special tool.
    a0041102.gif
  1. NOTE: Crankshaft sprockets are identical. They can only be installed one way. Refer to the following illustration for correct crankshaft sprocket installation.
    If removed, install LH and RH crankshaft sprockets.
    a14824b.gif
  1. Install the LH timing chain onto the crankshaft sprocket, aligning the one copper (marked) link on the timing chain with the slot on the crankshaft sprocket.
    a0041197.gif
  1. Position the LH timing chain on the camshaft sprocket with the two copper (marked) chain links and the camshaft sprocket timing mark aligned.
    a0049191.gif
  1. Position the RH (outer) timing chain on the crankshaft sprocket, aligning the copper (marked) link with the timing mark on the sprocket.
    a0041196.gif
  1. Position the RH timing chain on the camshaft sprocket. Make sure the two copper (marked) links align with the camshaft sprocket timing mark.
    a0041104.gif
  1. NOTE: LH shown; RH similar.
    Position the tensioner arms and tensioners, and install the bolts.
    aa5952a.gif
  1. Remove the tensioner retaining clip.
    a26273a.gif
  1. As a post-check, verify correct alignment of all timing marks.
    a0041106.gif
  1. Remove the special tool.
    aa5423a.gif
  1. Position the crankshaft sensor ring on the crankshaft.
    a0044041.gif
  1. Install the engine front cover. For additional information, refer to Engine Front Cover in this section.


2010&c18=modelyear&c20=n310677&c35=wsm%2ctiming%20drive%20components%2csxj%2c303-01b%2cin-vehicle%20repair&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Apr 03, 2010 | 1999 Ford Expedition

1 Answer

Replacing the timing belt on a 1998 Nissan Quest and need to know cam shaft and crank shaft positions.


go here for expert help on Villager & Quest

http://groups.yahoo.com/group/villagerquest/

e09cf57.gif

Item Part Number Description 1 — 40 Timing Chain/Belt Teeth 2 6256 Camshaft Sprocket , Front 3 — 43 Timing Chain/Belt Teeth 4 6306 Crankshaft Sprocket 5 6268 Timing Chain/Belt 6 6256 Camshaft Sprocket , Rear
Removal
  1. Drain the cooling system. Refer to Section 03-03 for the procedure.
  1. Disconnect the battery ground cable (14301) .
  1. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedure.
  1. If equipped, remove the three A/C compressor drive belt idler pulley bolts and the A/C compressor drive belt idler pulley.
  1. Remove the upper radiator hose bracket bolt.
  1. Loosen the two upper radiator hose clamps and remove the radiator hose bracket bolt. Remove the upper radiator hose (8260) and the upper radiator hose bracket from the vehicle.
  1. Remove the water bypass hose (8597) from between the thermostat housing and the water hose connection (8592) .
  1. Remove the main wiring harness from the upper engine front cover (6019) .
  1. Remove the eight upper engine front cover bolts and the upper engine front cover .
  1. Raise and support the vehicle.
  1. Remove the RH front wheel and tire assembly.
  1. Remove the four RH outer engine and transmission splash shield bolts and two screws and remove the RH outer engine and transmission splash shield (6775) .
  1. Use Strap Wrench 303-D055 (D85L-6000-A) or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts.
  1. Remove the water pump pulley from the water pump (8501) .
  1. Remove the crankshaft pulley (6312) . Refer to the procedure in this section.
  1. Remove the five lower engine front cover bolts and the lower engine front cover .
  2. Ensure that the timing marks between the crankshaft sprocket (6306) and the oil pump housing line up.
  3. NOTE: The directional arrow is necessary to ensure that the timing chain/belt (6268) can be reinstalled in the same direction.
  4. Loosen the timing chain/belt tensioner nut.
  5. Remove the timing chain/belt .

  6. Installation
    NOTE: Ensure that the timing marks on the camshaft sprockets (6256) and the seal plate are properly aligned. Ensure that the timing marks on the crankshaft sprocket and the oil pump housing are still aligned. NOTE: A new timing chain/belt has three white timing marks that indicate the correct timing positions of the camshafts (6250) and the crankshaft (6303) . These marks will help ensure that the engine (6007) is timed properly. When the engine is properly timed each white timing mark on the timing chain/belt will be aligned with the corresponding camshaft and crankshaft timing mark on the sprocket. Because the white timing marks are not evenly spaced you will need to refer to the following illustration for proper timing chain/belt placement. There should be 40 timing belt teeth between the timing marks of the front and rear camshaft sprockets and 43 teeth between the timing mark on the front camshaft sprocket and the timing mark on the crankshaft sprocket .

    NOTE: Verify that the camshaft timing marks are aligned with the timing marks on the seal plate, and that the crankshaft sprocket timing mark is aligned with the timing mark on the oil pump (6600) .

    Install the timing chain/belt starting at the crankshaft sprocket and moving around to the camshaft sprocket following a counterclockwise path. Do not allow any slack in the timing chain/belt between the timing sprockets. After all of the timing marks are matched up with the timing chain/belt installed, slip the timing chain/belt onto the timing chain/belt tensioner .





Sep 20, 2009 | 1998 Nissan Quest

1 Answer

Serpentine belt


5729dde.gif
This is a job for an experienced technician. Probably about a $300 job. Maybe more.

Here is procedure for 1996:

Removal
  1. Drain the cooling system. Refer to Section 03-03 for the procedure.
  1. Disconnect the battery ground cable (14301).
  1. Remove the generator drive belt, water pump and power steering pump drive belt, and the A/C compressor drive belt (if equipped). Refer to Section 03-05 for the removal procedure.
  1. If equipped, remove the three A/C compressor drive belt idler pulley bolts and the A/C compressor drive belt idler pulley.
  1. Remove the upper radiator hose bracket bolt.
  1. Loosen the two upper radiator hose clamps and remove the radiator hose bracket bolt. Remove the upper radiator hose (8260) and the upper radiator hose bracket from the vehicle.
  1. Remove the water bypass hose (8597) from between the thermostat housing and the water hose connection (8592).
  1. Remove the main wiring harness from the upper engine front cover (6019).
  1. Remove the eight upper engine front cover bolts and the upper engine front cover.
  1. Raise and support the vehicle.
  1. Remove the RH front wheel and tire assembly.
  1. Remove the four RH outer engine and transmission splash shield bolts and two screws and remove the RH outer engine and transmission splash shield (6775).
  1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley (8509) while removing the four water pump pulley bolts.
  1. Remove the water pump pulley from the water pump (8501).
  1. Remove the crankshaft pulley (6312). Refer to the procedure in this section.
  1. Remove the five lower engine front cover bolts and the lower engine front cover.
  2. Ensure that the timing marks between the crankshaft sprocket (6306) and the oil pump housing line up.
2acab54.gif
18. NOTE: The directional arrow is necessary to ensure that the timing chain/belt (6268) can be reinstalled in the same direction.

If the timing chain/belt is to be reused, mark the direction of rotation on the timing chain/belt.

19. Loosen the timing chain/belt tensioner nut.

  1. Remove the timing chain/belt.
Installation
NOTE: Ensure that the timing marks on the camshaft sprockets (6256) and the seal plate are properly aligned. Ensure that the timing marks on the crankshaft sprocket and the oil pump housing are still aligned.



stv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Pay special attention to the tooth shape of the timing belt. The current timing belts are not interchangeable with the timing belts from the 1993 model year. The 1993 model year uses a square or trapezoidal tooth timing belt while the current model year uses a rounded tooth design. The design change was made to extend the service life of the timing belt from 60,000 miles for the square or trapezoidal toothed belt to 105,000 miles for the rounded tooth belt. If the proper timing belt is not used, the customer may complain of a "whining" noise coming from the engine compartment. If the camshaft sprocket has a square cut in the valley of the gear tooth, it will require a square or trapezoidal tooth timing belt. If the camshaft sprocket has a rounded cut in the valley of the gear tooth, it will require a rounded tooth timing belt.
NOTE: If a new timing chain/belt is to be installed, make sure that the arrow is pointing away from the engine. If a timing chain/belt is to be reused, make sure that the directional arrow that was marked during disassembly is facing the correct direction.

NOTE: A new timing chain/belt has three white timing marks that indicate the correct timing positions of the camshafts and the crankshaft. These marks will help ensure that the engine (6007) is timed properly. When the engine is properly timed each white timing mark on the timing chain/belt will be aligned with the corresponding camshaft and crankshaft timing mark on the sprocket. Because the white timing marks are not evenly spaced you will need to refer to the following illustration for proper timing chain/belt placement. There should be 40 timing belt teeth between the timing marks of the front and rear camshaft sprockets and 43 teeth between the timing mark on the front camshaft sprocket and the timing mark on the crankshaft sprocket.

NOTE: Verify that the camshaft timing marks are aligned with the timing marks on the seal plate, and that the crankshaft sprocket timing mark is aligned with the timing mark on the oil pump (6600).

Install the timing chain/belt starting at the crankshaft sprocket and moving around to the camshaft sprockets following a counterclockwise path. Do not allow any slack in the timing chain/belt between the timing sprockets. After all of the timing marks are matched up with the timing chain/belt installed, slip the timing chain/belt onto the timing chain/belt tensioner.

  1. While holding the timing chain/belt tensioner with an Allen wrench, loosen the timing chain/belt tensioner nut.
  1. Allow the timing chain/belt tensioner to put pressure on the timing chain/belt.
  1. Use an Allen wrench to turn the timing chain/belt tensioner 70-80 degrees clockwise and tighten the timing chain/belt tensioner nut to 43-58 Nm (32-43 lb-ft).

    1. Rotate the crankshaft (6303) clockwise twice and align the No. 1 piston to Top Dead Center (TDC) on its compression stroke.
    1. Apply 98N (22 lbs) of force on the timing chain/belt between the rear camshaft sprocket and the timing chain/belt tensioner.
    2. NOTE: An assistant may be needed to adjust the timing chain/belt.

      While holding the timing chain/belt tensioner steady with an Allen wrench, loosen the timing chain/belt tensioner nut. Remove the Allen wrench and adjust the timing chain/belt tensioner as follows:
      1. Install a 0.35mm (0.0138 inch) thick and 12.7mm (0.500 inch) wide feeler gauge as shown.

  1. Turn the crankshaft clockwise to position the feeler gauge between the timing chain/belt tensioner and the timing chain/belt

  1. Tighten the timing chain/belt tensioner nut to 43-58 Nm (32-43 lb-ft).
  1. Turn the crankshaft clockwise to remove the feeler gauge from between the timing chain/belt tensioner and the timing chain/belt.
  1. Rotate the crankshaft clockwise twice and align the No. 1 piston to TDC on its compression stroke.
  1. Apply 98N (22 lbs) of force on the timing chain/belt between the rear and front camshaft sprocket.
    1. Measure the timing chain/belt deflection. Timing chain/belt deflection should be between 13-15mm (0.51-0.59 inch). If timing chain/belt deflection is not within specification, repeat steps 3-11. If the timing chain/belt cannot be adjusted to within specification, the timing chain/belt will have to be replaced.
    1. Position the lower engine front cover and install the five lower engine front cover bolts. Tighten the five lower engine front cover bolts to 3-5 Nm (27-44 lb-in).
    1. Install the outer timing chain/belt guide and the crankshaft pulley. Refer to the procedure in this section.
    1. Position the water pump pulley on the water pump and install the four water pump pulley bolts
    1. Use Strap Wrench D85L-6000-A or equivalent to hold the water pump pulley, and tighten the four water pump pulley bolts to 16-21 Nm (12-15 lb-ft).
    1. Position the RH outer engine and transmission splash shield and install the four RH outer engine and transmission splash shield bolts and two screws.
    1. Install the RH front wheel and tire assembly. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).



Feb 14, 2009 | 1993 Mercury Villager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8531 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...