Question about Ford Cars & Trucks

1 Answer

What transmissions will bolt up to a 2001 F-150 2WD 4.2L engine?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,036 Answers

Go to any auto parts stores they wikk kook up engine and transmission match you up with correct transmission.

Posted on Oct 16, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove oil pan



4x4
1. Open the hood.
2. Disconnect the battery negative cables.
3. Remove the intake air assembly.
4. Remove the radiator shroud retaining bolts.
5. Install engine support fixture # 8534B .
6. Raise and support the vehicle.

WARNING: HOT OIL CAN CAUSE PERSONAL INJURY.


7. Drain the engine oil (Refer to 09 - Engine/Lubrication/OIL - Standard Procedure) .
8. Loosen the front engine mount bolts.
9. Lower the vehicle.
10. Use the engine support fixture # 8534B to raise engine out of the front mounts.
11. Remove the engine oil dipstick.
12. Raise and support the vehicle.
13. Remove oil pan bolts, break the pan to block seal, and lower pan slightly and remove oil suction tube fasteners.
14. Remove oil pan and suction tube.
15. Remove the 2 bolts from the front of the engine block stiffener.
16. Remove the oil pan.


4x2
1. Open the hood.
2. Remove the negative battery cables.
3. Raise and support the vehicle.
4. Remove the transmission oil cooler lines.
5. Remove the propeller shaft.
6. Remove the starter bolts.
7. Support the starter.
8. Remove the torque converter bolts.
9. Remove the exhaust hanger bolts.
10. Remove the gear shift cable.
11. Remove the wiring harness.
12. Remove the transmission mount.
13. Remove the crossover bolts.
14. Position the transmission jack.
15. Remove the bell housing bolts.
16. Remove the transmission.
17. Remove the flywheel housing bolts (8).
18. Remove the flex plate bolts (8).
19. Remove the engine oil dip stick.
20. Drain the oil.
21. Remove the steering rack bolts.
22. Remove the oil pan bolts.
23. Remove the oil pickup bolts.
24. Remove the oil pan. user_online.gif

Aug 01, 2014 | Dodge Ram 3500 Cars & Trucks

2 Answers

Remove engine


call your buddies because you will need them for that, its not a one man job by a long shot.

Apr 06, 2014 | 1998 Plymouth Voyager

1 Answer

Cant get transmission bolts in transmisson


when installing transmission make sure dowel pins line up as move transmission toward engine,you have to raise engine slightly to make adjustment before bolts go back in transmission if transmission in a bind not align with engine transmission bolts will be harder to screw in place.

Aug 18, 2012 | 2004 Chevrolet TrailBlazer

2 Answers

Torque settings for 2005 lancer es fly wheel gearbox etc


2.0L Evolution engine

flywheel bolts 132 =/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.0L Non- Evolution engine

flywheel bolts 98 +/-5 N.m. 72 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

2.4L Ralliart engine

flywheel bolts 132 +/- 5 N.m. 98 +/- 3 ft lbs.

transmission to engine bolts 48 +/- 6 N.m. 36 +/- 4 ft lbs.

Dec 28, 2010 | 2005 Mitsubishi Lancer

1 Answer

I'm wondering whether on my 2003 (B6) S4 4,2l V8 cylinder n. 4 is the fourth one (front to rear) on left bank or the second on the right one. This just to understand the real firing order. Thank...


Firing order for 2003 (B6) Audi S4 4,2l V8 engine is: 1 - 5 - 4 - 8 - 6 - 3 - 7 - 2
Cylinder no.# 1 is first one from right front side of the car, and cylinder no.# 4 is the fourth one (front to rear) on the right bank of cylinder block. See picture below:

tdisline_88.jpg

Dec 08, 2010 | Audi S4 Cars & Trucks

1 Answer

I need to know how to seperate my transmission from my block


REMOVAL & INSTALLATION C6
  1. Disconnect the negative battery cable.
  2. From in the engine compartment, remove the two upper converter housing-to-engine bolts.
  3. Disconnect the neutral switch wire at the in-line connector.
  4. Remove the bolt securing the fluid filler tube to the engine cylinder head.
  5. Raise and support the truck on jackstands.
  6. Place the drain pan under the transmission fluid pan. Starting at the rear of the pan and working toward the front, loosen the attaching bolts and allow the fluid to drain. Finally remove all of the pan attaching bolts except two at the front, to allow the fluid to further drain. With fluid drained, install two bolts on the rear side of the pan to temporarily hold it in place.
  7. Remove the converter drain plug access cover from the lower end of the converter housing.
  8. Remove the converter-to-flywheel attaching nuts. Place a wrench on the crankshaft pulley attaching bolt to turn the converter to gain access to the nuts.
  9. With the wrench on the crankshaft pulley attaching bolt, turn the converter to gain access to the converter drain plug. Place a drain pan under the converter to catch the fluid and remove the plug. After the fluid has been drained, reinstall the plug.
  10. On 2WD drive models, disconnect the driveshaft from the rear axle and slide shaft rearward from the transmission. Install a seal installation tool in the extension housing to prevent fluid leakage.
  11. Disconnect the speedometer cable from the extension housing.
  12. Disconnect the downshift and manual linkage rods from the levers at the transmission.
  13. Disconnect the oil cooler lines from the transmission.
  14. Remove the vacuum hose from the vacuum diaphragm unit. Remove the vacuum line retaining clip.
  15. Disconnect the cable from the terminal on the starter motor. Remove the three attaching bolts and remove the starter motor.
  16. On 4WD drive models remove the transfer case.
  17. Remove the two engine rear support and insulator assembly-to-attaching bolts.
  18. Remove the two engine rear support and insulator assembly-to-extension housing attaching bolts.
  19. Remove the six bolts securing the No. 2 crossmember to the frame side rails.
  20. Raise the transmission with a transmission jack and remove both crossmembers.
  21. Secure the transmission to the jack with the safety chain.
  22. Remove the remaining converter housing-to-engine attaching bolts.
  23. Move the transmission away from the engine. Lower the jack and remove the converter and transmission assembly from under the vehicle. To install:
  24. Tighten the converter drain plug.
  25. Position the converter on the transmission making sure the converter drive flats are fully engaged in the pump gear.
  26. With the converter properly installed, place the transmission on the jack. Secure the transmission on the jack with the chain.
  27. Rotate the converter until the studs and drain plug are in alignment with their holes in the flywheel.
  28. Move the converter and transmission assembly forward into position, using care not to damage the flywheel and the converter pilot. The converter must rest squarely against the flywheel. This indicates that the converter pilot is not binding in the engine crankshaft.
  29. Install the converter housing-to-engine attaching bolts and tighten them to 65 ft. lbs. (88 Nm) for the diesel; 50 ft. lbs. (68 Nm) for gasoline engines.
  30. Remove the transmission jack safety chain from around the transmission.
  31. Position the No. 2 crossmember to the frame side rails. Install and tighten the attaching bolts.
  32. Install transfer case on 4WD drive models.
  33. Position the engine rear support and insulator assembly above the crossmember. Install the rear support and insulator assembly-to-extension housing mounting bolts and tighten the bolts to 45 ft. lbs. (61 Nm).
  34. Lower the transmission and remove the jack.
  35. Secure the engine rear support and insulator assembly to the crossmember with the attaching bolts and tighten them to 80 ft. lbs. (108 Nm).
  36. The balance of installation is the reverse of removal.
AOD
  1. Disconnect the negative battery cable.
  2. Raise the vehicle on hoist or stands.
  3. Place the drain pan under the transmission fluid pan. Starting at the rear of the pan and working toward the front, loosen the attaching bolts and allow the fluid to drain. Finally remove all of the pan attaching bolts except two at the front, to allow the fluid to further drain. With fluid drained, install two bolts on the rear side of the pan to temporarily hold it in place.
  4. Remove the converter drain plug access cover from the lower end of the converter.
  5. Remove the converter-to-flywheel attaching nuts. Place a wrench on the crankshaft pulley attaching bolt to turn the converter to gain access to the nuts.
  6. Place a drain pan under the converter to catch the fluid. With the wrench on the crankshaft pulley attaching bolt, turn the converter to gain access to the converter drain plug and remove the plug. After the fluid has been drained, reinstall the plug.
  7. On 2WD drive models, matchmark and disconnect the driveshaft from the rear axle and slide shaft rearward from the transmission. Install a seal installation tool in the extension housing to prevent fluid leakage.
  8. Disconnect the cable from the terminal on the starter motor. Remove the three attaching bolts and remove the starter motor. Disconnect the neutral start switch wires at the plug connector.
  9. Remove the rear mount-to-crossmember attaching bolts and the two crossmember-to-frame attaching bolts.
  10. Remove the two engine rear support-to-extension housing attaching bolts.
  11. Disconnect the TV linkage rod from the transmission TV lever. Disconnect the manual rod from the transmission manual lever at the transmission.
  12. Remove the two bolts securing the bell crank bracket to the converter housing.
  13. On 4WD drive models, remove the transfer case.
  14. Raise the transmission with a transmission jack to provide clearance to remove the crossmember. Remove the rear mount from the crossmember and remove the crossmember from the side supports.
  15. Lower the transmission to gain access to the oil cooler lines.
  16. Disconnect each oil line from the fittings on the transmission.
  17. Disconnect the speedometer cable from the extension housing.
  18. Remove the bolt that secures the transmission fluid filler tube to the cylinder block. Lift the filler tube and the dipstick from the transmission.
  19. Secure the transmission to the jack with the chain.
  20. Remove the converter housing-to-cylinder block attaching bolts.
  21. Carefully move the transmission and converter assembly away from the engine and, at the same time, lower the jack to clear the underside of the vehicle.
  22. Remove the converter and mount the transmission in a holding fixture.
  23. Tighten the converter drain plug. To install:
  24. Position the converter on the transmission, making sure the converter drive flats are fully engaged in the pump gear by rotating the converter.
  25. With the converter properly installed, place the transmission on the jack. Secure the transmission to the jack with a chain.
  26. Rotate the converter until the studs and drain plug are in alignment with the holes in the flywheel.
  27. Move the converter and transmission assembly forward into position, using care not to damage the flywheel and the converter pilot. The converter must rest squarely against the flywheel. This indicates that the converter pilot is not binding in the engine crankshaft.
  28. Install and tighten the converter housing-to-engine attaching bolts to 40-50 ft. lbs. (54-68 Nm).
  29. The balance of installation is the reverse of removal.
prev.gif next.gif

Nov 03, 2010 | 1991 Ford F150

1 Answer

How to remove a transmission for a 2002 GMC Yukon


Removal & Installation 4L60E/4L65E To Remove:
  1. Remove or disconnect the following:
    • Transmission fluid
    • Transmission oil level indicator tube and seal from the transmission
    • Plug the oil level indicator tube opening in the transmission.
    • Remove or disconnect the following:
    • Shift cable end from the transmission shift lever ball stud
    • If equipped with a transfer case, remove the front propeller shaft.
    • Rear propeller shaft.
  2. Plug the transmission oil cooler line connectors in the transmission case.
  3. Remove or disconnect the following:
    • Starter motor.
    • Transfer case, if equipped.
  4. Support the transmission with a transmission jack.
  5. Remove the transmission mount nuts.
  6. Remove the transmission crossmember.
  7. Remove or disconnect the following:
    • Torque converter access plug 4L60E/4L65E removal 9308kg37.gif

    • Flywheel to torque converter bolts
    • The two bolts securing the transmission rear mount to the transmission
    • The transmission vent hose, fuel lines, and the wiring harness from the transmission
    • The stud and the bolt securing the transmission to the engine
    • The six studs and one bolt securing the transmission to the engine. Install tool J21366 onto the transmission bell housing to retain the torque converter. Pull the transmission straight back.
    • The transmission from the vehicle
  8. Flush the transmission oil cooler and cooling lines when you remove the transmission.
To Install:
  1. Install or connect the following:
    • Tool J21366 onto the transmission bell housing to retain the torque converter.
    • Support the transmission with a transmission jack.
  2. Raise the transmission into place and remove the tool from the transmission.
  3. Slide the transmission straight onto the locating pins while lining up the marks on the flywheel and the torque converter. The torque converter must be flush onto the flywheel and rotate freely by hand.
  4. Install or connect the following:
    • Six studs and one bolt securing the transmission to the engine. Tighten the studs and the bolt to 50 Nm (37 ft. lbs.).
    • Stud and bolt securing the transmission to the engine. Tighten the stud and the bolt to 50 Nm (37 ft. lbs.).
    • Flywheel to torque converter bolts. Tighten the stud and the bolt to 46 Nm (63 ft. lbs.).
    • Torque converter access plug.
    • Transmission vent hose, fuel lines, and the wiring harness to the transmission.
    • Two bolts securing the heat shield to the transmission. Tighten the bolt to 17 Nm (13 ft. lbs.).
    • Two bolts securing the transmission rear mount to the transmission. Tighten the bolts to 18 ft. lbs. (25 Nm).
    • Install the transmission crossmember. Tighten the nuts and bolts to 70 ft. lbs. (95 Nm).
  5. Remove the transmission jack from the transmission.
  6. Unplug the transmission oil cooler line connectors in the transmission case.
  7. Install or connect the following:
    • Starter
    • Transmission oil cooler lines to the transmission
    • If equipped with a transfer case, install the front propeller shaft.
    • The rear propeller shaft
    • The shift cable end to the transmission shift lever ball stud
  8. Unplug the oil level indicator tube opening in the transmission.
  9. Install the transmission oil level indicator tube and seal to the transmission.
  10. Tighten the oil pan bolts and fill the transmission with transmission fluid.
  11. Lower the vehicle.
4L80E/4L85E To Remove:
  1. Remove or disconnect the following:
    • Transmission fluid
    • Transmission oil level indicator tube and seal from the transmission
  2. Plug the oil level indicator tube opening in the transmission.
  3. Remove or disconnect the following:
    • Shift cable from the transmission shift lever ball stud
    • If 4WD vehicle, remove the propeller shaft.
    • If RWD vehicle, remove the propeller shaft.
    • The transmission oil cooler lines from the transmission
  4. Plug the transmission oil cooler line connectors in the transmission case.
  5. Remove or disconnect the following:
    • Starter motor
  6. Support the transmission with a transmission jack.
  7. Remove or disconnect the following:
    • The two bolts securing the heat shield to the transmission
    • The transmission vent hose, fuel lines, and the wiring harness from the transmission
    • One nut and one bolt securing the transmission brace to the engine bracket and transmission
    • The two bolts securing the torque converter cover to the engine
    • The four bolts securing the torque converter cover to the transmission
    • The six flywheel to torque converter bolts
    • The two bolts and nut securing the transmission rear mount to the transmission
    • The stud and the bolt on the right side securing the transmission to the engine
    • The remaining six studs and the one bolt securing the transmission to the engine
    • Tool J21366 onto the transmission bell housing to retain the torque converter
    4L80E/4L85E removal 9308kg36.gif

  8. Pull the transmission straight back. Remove the transmission from the vehicle.
  9. Flush the transmission oil cooler and cooling lines when you remove the transmission.
To Install:
  1. Install or connect the following:
    • Tool J21366 onto the transmission bell housing to retain the torque converter
  2. Support the transmission with a transmission jack.
  3. Raise the transmission into place and remove the tool from the transmission.
  4. Slide the transmission straight onto the locating pins while lining up the marks on the flywheel and the torque converter. The torque converter must be flush onto the flywheel and rotate freely by hand.
  5. Install or connect the following:
    • Six studs and one bolt securing the transmission to the engine. Tighten the studs and the bolt to 50 Nm (37 ft. lbs.).
    • The stud and bolt on the right side securing the transmission to the engine. Tighten the stud and the bolt to 50 Nm (37 ft. lbs.).
    • Six flywheel to torque converter bolts. Tighten the bolts to 60 Nm (44 ft. lbs.).
    • The two bolts securing the torque converter cover to the engine. Tighten the bolt to 50 Nm (37 ft. lbs.).
    • The four bolts securing the torque converter cover to the transmission. Tighten the stud and the bolt to 33 Nm (24 ft. lbs.).
    • The transmission vent hose, fuel lines, and the wiring harness to the transmission.
    • The two bolts securing the heat shield to the transmission. Tighten the bolt to 17 Nm (13 ft. lbs.).
    • The two bolts and nut securing the transmission rear mount to the transmission. Tighten the bolts and nut to 25 Nm (18 ft. lbs.).
    • The flywheel to torque converter bolts.
    • One nut and one bolt securing the transmission brace to the engine bracket and transmission. Tighten the bolts and nut to 50 Nm (37 ft. lbs.).
  6. Remove the transmission jack from the transmission.
  7. Install or connect the following:
    • Starter motor
  8. Unplug the transmission oil cooler line connectors in the transmission case.
  9. Connect the transmission oil cooler lines to the transmission.
  10. Install or connect the following:
    • The transfer case
    • The rear propeller shaft
    • The shift cable end to the transmission shift lever ball stud
  11. Unplug the oil level indicator tube opening in the transmission.
  12. Install the transmission oil level indicator tube and seal to the transmission.
  13. Tighten the oil pan bolts and fill the transmission with transmission fluid.
  14. Lower the vehicle.
prev.gif next.gif

Oct 12, 2010 | 2002 GMC Yukon XL

1 Answer

How does transmission come out


prev.gif next.gif Transmission Assembly REMOVAL & INSTALLATION C6
  1. Disconnect the negative battery cable.
  2. From in the engine compartment, remove the two upper converter housing-to-engine bolts.
  3. Disconnect the neutral switch wire at the in-line connector.
  4. Remove the bolt securing the fluid filler tube to the engine cylinder head.
  5. Raise and support the truck on jackstands.
  6. Place the drain pan under the transmission fluid pan. Starting at the rear of the pan and working toward the front, loosen the attaching bolts and allow the fluid to drain. Finally remove all of the pan attaching bolts except two at the front, to allow the fluid to further drain. With fluid drained, install two bolts on the rear side of the pan to temporarily hold it in place.
  7. Remove the converter drain plug access cover from the lower end of the converter housing.
  8. Remove the converter-to-flywheel attaching nuts. Place a wrench on the crankshaft pulley attaching bolt to turn the converter to gain access to the nuts.
  9. With the wrench on the crankshaft pulley attaching bolt, turn the converter to gain access to the converter drain plug. Place a drain pan under the converter to catch the fluid and remove the plug. After the fluid has been drained, reinstall the plug.
  10. On 2WD drive models, disconnect the driveshaft from the rear axle and slide shaft rearward from the transmission. Install a seal installation tool in the extension housing to prevent fluid leakage.
  11. Disconnect the speedometer cable from the extension housing.
  12. Disconnect the downshift and manual linkage rods from the levers at the transmission.
  13. Disconnect the oil cooler lines from the transmission.
  14. Remove the vacuum hose from the vacuum diaphragm unit. Remove the vacuum line retaining clip.
  15. Disconnect the cable from the terminal on the starter motor. Remove the three attaching bolts and remove the starter motor.
  16. On 4WD drive models remove the transfer case.
  17. Remove the two engine rear support and insulator assembly-to-attaching bolts.
  18. Remove the two engine rear support and insulator assembly-to-extension housing attaching bolts.
  19. Remove the six bolts securing the No. 2 crossmember to the frame side rails.
  20. Raise the transmission with a transmission jack and remove both crossmembers.
  21. Secure the transmission to the jack with the safety chain.
  22. Remove the remaining converter housing-to-engine attaching bolts.
  23. Move the transmission away from the engine. Lower the jack and remove the converter and transmission assembly from under the vehicle. To install:
  24. Tighten the converter drain plug.
  25. Position the converter on the transmission making sure the converter drive flats are fully engaged in the pump gear.
  26. With the converter properly installed, place the transmission on the jack. Secure the transmission on the jack with the chain.
  27. Rotate the converter until the studs and drain plug are in alignment with their holes in the flywheel.
  28. Move the converter and transmission assembly forward into position, using care not to damage the flywheel and the converter pilot. The converter must rest squarely against the flywheel. This indicates that the converter pilot is not binding in the engine crankshaft.
  29. Install the converter housing-to-engine attaching bolts and tighten them to 65 ft. lbs. (88 Nm) for the diesel; 50 ft. lbs. (68 Nm) for gasoline engines.
  30. Remove the transmission jack safety chain from around the transmission.
  31. Position the No. 2 crossmember to the frame side rails. Install and tighten the attaching bolts.
  32. Install transfer case on 4WD drive models.
  33. Position the engine rear support and insulator assembly above the crossmember. Install the rear support and insulator assembly-to-extension housing mounting bolts and tighten the bolts to 45 ft. lbs. (61 Nm).
  34. Lower the transmission and remove the jack.
  35. Secure the engine rear support and insulator assembly to the crossmember with the attaching bolts and tighten them to 80 ft. lbs. (108 Nm).
  36. The balance of installation is the reverse of removal.

Aug 26, 2010 | 1993 Ford F250

2 Answers

Do i have to pull the motor out of a 1997 chevy s-10 to remove the transmission?


Removal & Installation To Remove:
Transmission mounting on 2.2L engines 88457g33.gif

Transmission mounting on 4.3L engines 88457g34.gif

  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely using jackstands.
  3. Drain the transmission fluid.
  4. Remove the driveshaft from the transmission (2WD) and transfer case, if equipped (4WD or AWD).
  5. Support the transmission with a suitable transmission jack.
  6. Remove the shift cable from the transmission control lever and bracket.
  7. Remove the nut and washer securing the transmission mount to the crossmember.
  8. Remove the bolts and washers securing the mount to the transmission.
  9. Disconnect the exhaust pipe from the exhaust manifold(s).
  10. If equipped, remove the bolts securing the converter pan cover to the transmission.
  11. Remove the 3 bolts securing the torque converter to the flywheel.
  12. Remove the bolt, clip, and strap securing the three fuel lines and transmission vent hose to the transmission case.
  13. Remove the bolts and nut securing the transmission to the engine.
  14. Remove the oil filler tube and seal from the transmission.
  15. Disconnect the transmission cooler lines from the transmission. Plug the lines and the ports in the transmission.
  16. Unplug the wiring harness connectors from the transmission.
  17. Inspect for any other wiring, brackets etc. which may interfere with the removal of the transmission.
  18. Since the transmission acts as a rear engine mount, properly support the rear of the engine with an underbody support of other suitable support before attempting to remove the transmission. Otherwise the rear of the engine may pitch downward and components on the rear of the engine and on the firewall may be damaged.
  19. Remove the transmission from the engine by pulling the transmission rearward to disengage it from the locator dowel pins on the back of the block. Carefully lower the transmission from the vehicle. Use care that the torque converter does not fall out of the front of the transmission

Jul 16, 2010 | 1997 Chevrolet S-10 Pickup

2 Answers

1997 z71 Transmission removal




  1. Disconnect the battery negative cable.
  2. Raise the vehicle. Support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  3. Disconnect the range selector cable from the transmission bracket and from the transmission range select lever. Refer to Shift Cable Replacement .
  4. Remove the rear propeller shaft. Refer to Rear Propeller Shaft in Propeller Shaft.
  5. Support the transmission with a transmission jack.
  6. Remove the transfer case if equipped. Refer to the appropriate Transfer Case Replacement in Transfer Case:
  7. Transfer Case Replacement (Selectable Four Wheel Drive) . • Transfer Case Replacement (Auto Four Wheel Drive ) . • Transfer Case Replacement (Manual Four Wheel Drive) .
    102329.gif
    tif.gif
  8. Gasoline Engine--Remove the following components:
  9. 7.1. Two bolts 7.2. Two washers 7.3. One nut 7.4. The transmission to engine brace
    102332.gif
    tif.gif
  10. Diesel Engine--Remove the following components:
  11. 8.1. Two bolts 8.2. Two washers 8.3. One nut 8.4. The transmission to engine brace
  12. Remove the transmission rear mount.
  13. Remove the frame crossmember.
  14. Remove the exhaust pipe from the exhaust manifolds. Remove the muffler assembly from the exhaust pipe, if required. Refer to Exhaust System.

  15. 102208.gif
    tif.gif
  16. For the 5.0L Gasoline Engine: Remove the six bolts securing the converter cover to the transmission.
  17. Remove the starter. Refer to Starter Replacement in Engine Electrical.
  18. For the 4.3L Gasoline Engine: Remove the dust plug at the end of the starter mounting port in order to gain access to the converter bolts.

  19. 102335.gif
    tif.gif
  20. For the Diesel Engine and 7.4L/5.7L Engines: Remove the four bolts securing the converter cover to the transmission.
  21. Mark the flywheel and the torque converter alignment.

  22. 102211.gif
    tif.gif
  23. Remove the bolts that attach the torque converter to the engine flywheel.

  24. 102339.gif
    tif.gif
  25. Remove the transmission vent hose.
  26. Disconnect the wiring harness connectors from the vehicle speed sensors and from the park neutral position switch.
  27. Remove all vehicle electrical harness wires, harness clips, tubes, and brackets that may interfere with the removal of the transmission.
  28. Remove the fluid fill tube and the fill tube seal from the transmission. Refer to Filler Tube Replacement .
  29. Plug the fluid fill tube opening in the transmission.
  30. Disconnect the transmission oil cooler pipes from the transmission. Refer to the oil cooler pipe quick connect fittings removal procedure in Oil Cooler Hose/Pipe Replacement .
  31. Plug the transmission oil cooler pipe connectors in the transmission case.
  32. Install the J 21366 in order to keep the torque converter from sliding off of the transmission turbine shaft.
  33. Support the engine with a suitable jack stand before removing the transmission from the engine.

  34. 102341.gif
    tif.gif
  35. 5.0L and 5.7L Gasoline Engine: Remove the studs and bolts securing the transmission to the engine.

  36. 102343.gif
    tif.gif
  37. 4.3L Gasoline Engine: Remove the studs and bolts securing the transmission to the engine.
  38. Pull the transmission straight back from the engine.
  39. Lower the transmission using the transmission jack.
  40. Flush the transmission oil cooler and the pipes whenever you remove the transmission for overhaul, or replacement of the torque converter, the pump, or the transmission case. Refer to Transmission Fluid Cooler Flushing .
  41. Clean the transmission case using a solvent dampened cloth. Do not allow solvent to enter the transmission.
  42. Air dry the transmission.
  43. Clean all hardware and the flywheel cover using solvent. Air dry all the parts.
  44. Inspect all the components for wear and damage.
  45. Inspect all the seals and the fittings for signs of wear.
  46. Inspect the torque converter for stripped or broken weld nuts.
  47. Inspect the transmission case for cracks.

Jul 06, 2009 | 1997 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

fordexpert

Level 3 Expert

5546 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...