Question about 2010 Suzuki SX4

Open Question

Remove rear combination light - 2010 Suzuki SX4

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove bumper


1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly.

2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. D. Remove two screws from side of bumper assembly. E. Remove four bumper mounting bolts from under of vehicle.
3. Install rear bumper in reverse order of removal.

Dec 22, 2013 | 2004 Kia Sedona

2 Answers

How can i change a tail light an a sorento kia 2008? I can t reach the connector inside..... What do i have to take off? Thank you


To Remove

1. Disconnect the negative (-) battery terminal.
2. Loose the 2 screws holding the rear combination lamp then disconnect the connector. And then remove the outside rear combination lamp assembly.
3. Remove the bulbs from the rear combination lamp assembly.


tecnovative_179.gif

tecnovative_180.gif
To Install

1. Connect the bulbs to the rear combination lamp assembly.
2. Connect the rear combination lamp connector.
3. Reassemble the rear combination lamp assembly.

Mar 24, 2011 | 2007 Kia Sorento LX 4x4

1 Answer

How do you replace the brake light on a Nissan Altima 2005


Rear Turn Signal, Brake and Parking Lights Removal and Installation To Remove:
  1. Remove or disconnect the following:
    • Trunk trim as needed
    • Nuts securing rear combination lamp assembly, from inside the trunk
    • Connectors
    • Combination lamp assembly
To Install:
  1. Install or connect the following:
    • Combination lamp assembly and connectors
    • Nuts securing combination lamp assembly
      1. Torque to: 22-33 in. lbs. (2.5-3.7 Nm)
  2. Replace trunk trim.

Nov 12, 2010 | 2005 Nissan Altima

1 Answer

I need to replace the driver's side brake light.


Rear Combination Light- 2007 might vary from these diagrams:
Removal & Installation 2004 (Early Production) 4 Door To Remove:
  1. Disconnect battery negative cable.
  2. Disconnect electrical connector. Rear Combination Light kia-06-18-7495.gif

  3. Remove 2 screws and 2 nuts and remove light assembly.
To Install:
  1. Install light assembly and 2 screws and 2 nuts.
  2. Connect electrical connector.
  3. Connect battery negative cable.
5 Door To Remove:
  1. Disconnect battery negative cable.
  2. Disconnect electrical connector. Rear combination light kia-06-18-7496.gif

  3. Remove 2 screws and push light assembly toward outside of vehicle. CAUTION
    Use care to not damage gasket.
  4. Pull rear combination light from vehicle.
To Install:
  1. Install rear combination light and 2 screws.
  2. Install 2 screws.
  3. Connect electrical connector.
  4. Connect battery negative cable.
2004 (Late Production), 2005-2009 To Remove:
Turn Signal Lamp kia-06-20-7698.gif

  1. Disconnect battery negative cable.
  2. Remove 2 screws and cover inside trunk.
  3. Remove 4 nuts and disconnect electrical connector (A).
  4. Remove rear combination lamp.
To Install:
Turn Signal Lamp kia-06-20-7698.gif

  1. Install rear combination lamp.
  2. Install 4 nuts and connect electrical connector (A).
  3. Install cover inside trunk and install 2 screws.
  4. Connect battery negative cable.
prev.gif next.gif

Oct 28, 2010 | 2007 Kia Spectra5

1 Answer

2005 maxima-how to change break lights


Removal and Installation
  1. Position trunk room trim aside.
  2. Disconnect rear combination lamp connector.
  3. Remove rear combination lamp mounting nuts.
  4. Pull rear combination lamp to remove from the vehicle.Installation is in the reverse order of removal.

    Once you have all the nuts removed you will need to pull hard on the lens. They use push clips on the outer side of the lens. As long as you apply an even amount of force you will not damage anything.

Nov 26, 2009 | 1992 Nissan Maxima

1 Answer

How to remove the rear bumper on a 2005 Kia Sedona


1. Remove rear combination light assembly. A. Remove two mounting screws. B. Disconnect electrical connector from rear side of light assembly. bs6d007a.gif 2. Remove bumper assembly. A. Remove four fasteners and four retaining screws from top of bumper assembly. bs6d007d.gif B. Remove mud flap from bumper assembly. C. Remove two screws from bottom of bumper assembly. bs6d007e.gif D. Remove two screws from side of bumper assembly. bs6d007b.gif E. Remove four bumper mounting bolts from under of vehicle. bs6d007c.gif 3. Install rear bumper in reverse order of removal.

Nov 09, 2009 | 2005 Kia Sedona

1 Answer

How do you change tail lights for the 2003 passat


Rear Turn Signal, Brake and Parking Lights Removal & Installation To Remove
  1. Remove or disconnect the following:
    • Harness connector
    • Combination nuts
    • Lamp and its assembly toward rear
To Install:
  1. Install or connect the following:
    • Lamp and its assembly into position
    • Combination nuts; torque to 35 lb-in. (4 Nm)
    • Harness connector
This is the only thing the tech manual says.

Jul 22, 2009 | 2003 Volkswagen Passat

2 Answers

Parking lights burnt out on my 2005 Rave 4


Do them yourself!

Remove or disconnect the following:
  • Rear combination lamp service cover
  • Connector
d66b228.gif
2 nuts and rear combination lamp assembly


5e1be51.gif

Mar 29, 2009 | 2004 Toyota RAV4

1 Answer

How do I replace a taillight lens on a 1991 Geo Storm?


Rear Turn Signal, Brake and Parking Lights


STORM COUPE
  1. Disconnect the negative battery cable.
  2. Lift the luggage compartment floor carpet toward the front of the vehicle and remove the spare tire cover panel.
  3. Remove the ten plastic retaining clips from the rear end trim panel.
  4. Disconnect the luggage compartment lamp electrical connector.
  5. Remove the luggage compartment trim panel and the rear end trim panel.
  6. Disconnect the rear combination lamp assembly electrical connector. Fig. 1: Rear Turn Signal, Brake and Parking Lights — Storm
84256028.gif
  1. Remove the seven nuts and the rear combination lamp assembly from the vehicle.
  2. Disconnect the rear combination lamp electrical connector.
  3. Remove the four bulb sockets from the rear combination lamp assembly and remove the four bulbs from the sockets. To install:
  4. Install the four bulbs to the sockets and install the four bulb sockets to the rear combination lamp assembly.
  5. Connect the rear combination lamp electrical connector.
  6. Install the rear combination lamp assembly to the vehicle and the seven nuts.
  7. Connect the rear combination lamp assembly electrical connector.
  8. Install the rear end trim panel and the luggage compartment trim panel.
  9. Connect the luggage compartment lamp electrical connector.
  10. Install the ten plastic retaining clips to the rear end trim panel.
  11. Install the spare tire cover panel and the luggage compartment floor carpet.
  12. Connect the negative battery cable.

Mar 21, 2009 | 1991 Geo Storm

1 Answer

97 FORD CONTOR NO BRAKE LIGHTS INSIDE REAR WINDOW BRAKE LIGHT WORKS,SIGNALS WORK EMEGENCY WORKS TOO ,BUT NO BRAKE LIGHTS. HELP!


If there is no fuse that is blown, then according to wiring diagrams on autozone.com repair info link it must be the combination switch: http://econtent.autozone.com:24991/znetrgs/repair_guide_content/en_us/images//0900c152/80/0a/8d/31//large/0900c152800a8d31.gif

My mother's brake lights (1996 Ford Contour) were not working and it was the combination switch. The combination switch is an assembly by the wheel, you use it to give turn signals, high beam, hazard lights and apparently the 'smart' Ford designers linked the rear brake lights to it. Could be a contact that is oxidized. I repaired mine. I may have one lying around. You can get this from a junk yard. I believe it is pretty simple to remove.

Aug 21, 2008 | 1995 Ford Contour

Not finding what you are looking for?
2010 Suzuki SX4 Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...