Question about Lexus Cars & Trucks

Open Question

Need torque specs for trans pan on a 97 lexus es300

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75117 Answers

SOURCE: Transmission toque specs

The spec is 12 ft lbs of torque. Use a an even pattern when you tighten the bolts, this assures the gasket will not be damaged and create another leak.

Posted on Jul 27, 2008

  • 6982 Answers

SOURCE: Need torque specs for oil pan gasket

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

  • 6 Answers

SOURCE: amplifier location 1993 lexus es300

My Son has a 95 es300, the amp for it is located under the front passenger seat. The easiest way to access it is to remove the 4 bolts holding the seat down, and remove the seat. Takes about 5 minutes

Posted on Jul 24, 2009

  • 153 Answers

SOURCE: I need a replacement key for my lexus ES300? Is it

call the dealer and a couple of lock smiths that deal with cars, the lock smiths a generally lower in price.

Posted on Feb 28, 2010

Greycap
  • 47 Answers

SOURCE: code p0420 on 97 lexus

P0420 is catalyst below threshold. It is triggered via the rear o2 sensor (post cat), so you may want to check that sensor to make sure it's functioning properly.

Posted on Oct 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2088 ford explorer 50,000 miles small spots of transmission fluid on driveway, is this going to be a huge transmission repair?


You could just have loose trans pan bolts or leaks at cooling line fittings. I don't have the Torque specs on hand for the trans bolts but you will need a smaller Torque Wrench rated in inch-lbs. rather than foot-lbs. for the small size these units use.

What you could try is a trans filter change/cleaning which is done by taking the trans pan off and servicing the trans filter. The pan would be reinstalled.

Now go to a shop which uses new pan gaskets because your old one may be leaking and may need to replaced anyway.

SOME FAST CHANGE OIL SERVICES OFFER TRANSMISSION FLUID SERVICES-BUT THEY WILL ONLY PUMP OUT THE OLD FLUID WITH A MACHINE AND WILL NOT REMOVE THE TRANS PAN. Your trans needs to be looked at for leaks and the above procedure will not fix your problem.

It is not impossible to have a tailshaft seal leak or shift solenoid covers leak, even a speedometer cable fitting can leak. A visual inspection will tell.

If you are careful, and find a leaking trans pan, tightening it up with a 1/4 inch drive Rachet is all you need in lieu of a Torque wrench. Can not emphasize enough not to reef on these tiny bolts.

Oct 07, 2013 | Ford Cars & Trucks

1 Answer

Hard shfit into reverse, and no light on gear indicator


I was about to say rebuild it

You need to stop using i say as a former
trans shop owner & hope the damage isn't
done already

You have solenoid issues every where
Delayed reverse
Torque Converter Chatter
Delayed Shifts

Hope the trans was built correctly
Now you need to diagnose the ENTIRE
cars systems,all of them

You have no real shift strategy at all

May be a sensor you don't see associated with
the trans

I can't guess,just spoke my mind

Dec 01, 2012 | Cars & Trucks

1 Answer

I need help on removing my transmission from my es300 and on how to install a new one


its easiest pull the engine and trans assembly then separate them then set them back in you have to remove the axles. Dont forget the torque converter bolts its a big job.

Dec 08, 2010 | Lexus ES 300 Cars & Trucks

1 Answer

Need to know what the torque spec is for my 1997 pontiac sunfire trans pan, 12 bolt pan. its a 4 speed auto.


HI, the torque spec for the pan bolts is 14nm or 124 in lb. snug them down evenly it doesn't take much to over tighten these and strip out the threads.

Aug 28, 2010 | Pontiac Sunfire Cars & Trucks

1 Answer

What is the torque ratio for 1994 es300 connecting rod bearings bolts


The torque spec for the connecting rod bearig bolts for a 1994 lexus es300 is

step 1) 18 ft lbs
step 2) tighten an addtional 90 degrees.

Hope this helps.

Jun 16, 2010 | 1994 Lexus Es 300

2 Answers

Torque specs for the trans pan bolts 1990 ford probe automatic?


The tightening is less torque, buyt rather gasket and pan squish.... barley gets tight, but too much and leaks happen.

Be certain to reform the pan bolt holes before you replace the pan.

So tightening happens evenly and stop just as the gasket shows deformation. This is after even tightening 2 or 3 steps....

Sep 20, 2009 | 1990 Ford Probe

1 Answer

Nedd extra ignition key for 97 lexus es300


go to toyota and give them your vin number

May 29, 2009 | 1997 Lexus ES 300

1 Answer

Need torque specs for oil pan bolts


torque specs for these bolts can be found in a Haynes or Chilton manual availiable from your local parts store, or maybe at your local library, however these bolts are usually no more than 14 ft pounds, unlike cylinder head bolts, the bolts do not need to have any stretch factor to hold the oil pan gasket in place or sealed.

May 17, 2009 | 1997 Ford Ranger SuperCab

2 Answers

Upgrade 97 Lexus ES300 Steering wheel to 2001.


Yes you can switch steering wheels, the wood grain is pricy. disconect the battery, wait 5min. remove caps from side of steering wheel. remove torx bolts from air bag assy. Remove wires from air bag. Place air bag upsode down in passenger seat. Make sure steering wheel is straight, remove 19mm nut and remove steering wheel.

Mar 06, 2009 | 1997 Lexus ES 300

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...