Question about 1998 Nissan Altima

Open Question

2000 Nissan xterra with codes p0325 p1441 and p1126 with a bad miss

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 14 Answers

SOURCE: Service Engine light on DTC Codes P1126 & P0325

change the temp sensor

Posted on May 16, 2009

Ad
  • 2418 Answers

SOURCE: nissan

OK the sensor may not be bad, you might have a broken wire to the sensor. Or a bad plug, I would by pass the sensor plug - cut it out. Cut one wire at the time and reconect using a crimp on union (bu**) conector. You may also have a timing issue, that a tune up might fix..

Posted on Oct 17, 2009

Testimonial: "the code is when in star the car. made up tun. give me your email please"

Danniboi
  • 1098 Answers

SOURCE: what is throttle control motor relay circuit for

This is the electronic control module to keep the idle of the revs correct it also allows the correct amount of fuel to air mixture the car needs to run. some are called EGR some are ICV idle control valve

Posted on Jan 20, 2010

  • 3640 Answers

SOURCE: Nissan altima 2000 with engine service light on.

p0325 is, ignition system or misfire, could be plugs, wires, or a bad coil. p1126 throttle control motor relay curcuit open.P1126 Power supply for the throttle control motor is provided to the ECM via throttle control motor relay. The throttle control motor relay is ON/OFF controlled by the ECM. When the ignition switch is turned ON, the ECM sends an ON signal to throttle control motor relay and battery voltage is provided to the ECM. When the ignition switch is turned OFF, the ECM sends an OFF signal to throttle control motor relay and battery voltage is not provided to the ECM. possible cause, Harness or connectors (Throttle control motor relay circuit is open Throttle control motor relay.

Posted on May 07, 2010

alicantecoli
  • 22219 Answers

SOURCE: meaning of p1126 manufacturer control fuel air

think it means the mass air flow in the intake pipe not reading correct

Posted on Dec 10, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do I fix my 2000 nissan Xterra It will start up and soon as it warms up It starts missing and backfiring


if you never fix the problems , and just clear codes it is only going to keep getting worse . missing and backfiring sounds like you have a timing problem and it will only get worse too .

Nov 05, 2015 | 2000 Nissan Xterra

2 Answers

Check engine soon. giving codes p0120, p1705, p0325


TPS sensor (RPM) po120,knock sensor po325.

Mar 25, 2015 | 2001 Nissan Xterra

1 Answer

2000 xterra code p0325 the common issue


It will not pass inspection.
P0325 NISSAN - Knock Sensor Circuit Malfunction xicon.jpghttp://engine-codes.com/p0325_nissan.htmlForum CodePossible causes- Faulty knock sensor
- Knock sensor circuit short to ground
- Knock sensor circuit short to power
- Knock sensor circuit open
- Faulty Engine Control Module (ECM) Tech notes Very common problem with Nissan vehicles. Replacing the knock sensor usually takes care of the problem.

Jul 03, 2012 | Nissan Xterra Cars & Trucks

1 Answer

I have a 2000 Nissan Xterra with 2 error codes: PO325 and PO303. What needs to be repaired/replaced?


P0325 knock sensor 1 circuit malfunction bank 1 or 1 sensor, the knock sensor should be check/replaced. You can buy Haynes Repair Manuals at Pepboys that will walk you throught the process step by step.
P0303 is a cylinder misfire in cylinder 3 which may mean it could either be the spark plug, coil or the injector.

May 03, 2011 | 2001 Nissan Xterra

2 Answers

I have on 01 xterra-service engine light on-codes P1126 & P0325. I think the battery is about to go,could it be realated to codes? Otherwise what do the codes mean? Appreciate any help


Your battery has nothing to do with these codes. Your vehicles computers have detected a malfunction or failure in the system. This triggers these codes and sets your check engine light. Below I have listed the code meanings and some repair solutions.

P1126 - Throttle Position (Narrow Range) Sensor Circuit Malfunction.

Power supply for the throttle control motor is provided to the ECM via throttle control motor relay. The throttle control motor relay is ON/OFF controlled by the ECM. When the ignition switch is turned ON, the ECM sends an ON signal to throttle control motor relay and battery voltage is provided to the ECM. When the ignition switch is turned OFF, the ECM sends an OFF signal to throttle control motor relay and battery voltage is not provided to the ECM.

Possible Causes For P1126:
- Harness or connectors (Throttle control motor relay circuit is open)
- Throttle control motor relay


P0325 - Knock Sensor Circuit Malfunction

The knock sensor is attached to the cylinder block. It senses engine knocking using a piezoelectric element. A knocking vibration from the cylinder block is sensed as vibrational pressure. This pressure is converted into a voltage signal and sent to the Powertrain Control Module (PCM) or Electronic Control Module (ECM).

Possible Causes For P0325:
- Knock sensor circuit short to ground.
- Knock sensor circuit short to power.
- Knock sensor circuit open.
- Damaged knock sensor.
- Damaged PCM or ECM

Possible Solutions:
- Repair or resecure harness or connector
- Replace knock sensor Bank 1 (Bank 1 if applicable)
- Replace PCM or ECM

The P0325 DTC is a very common problem with Nissan vehicles. On most Nissan vehicles the knock sensor is located on top of the engine block.

knock_sensor_infiniti.gif

Jan 20, 2011 | 2001 Nissan Xterra

1 Answer

2000 xterra v6 when it warms up it starts to miss badly, sputter and die. When it cools off it runs fine. I get a knock sensor (p0325) code on th ecomputer.


well i wouldnt place any emphasis on a generic code like this ,they dont always read correct especially on europeon market vehicles ,My first thought is the autochoke temperature sensor ,so when its cold it runs but when it warms up its running rich ,or a O2 sensor heater is playing up

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

knock sensor ??? dont think this is refering to the airbag but more like a sensor to `prevent pre detonation of fuel ,check the heater circuits on the O2 sensors ,their the two wires the same colour ,disconnect the plug and see if you have continuity across these two wires ,their are two sensors on this year one before and one after the cat ,not sure what is bank one though so check all four ,cant find this vehicle in my alldata books ,diesel yes i have a customer X trail but V6 petrol i have never seen

Jan 07, 2011 | 2000 Nissan Xterra

1 Answer

Code P0325 Knock sensor 1 circuit malfunction (bank 1 or single sensor)


Code P0325 Knock sensor 1 circuit malfunction (bank 1 or single sensor)

May 15, 2010 | 2002 Nissan Xterra

1 Answer

Nissan altima 2000 with engine service light on. fault codes per mechanic p0325 and p1126. But he said mass air flow sensor malfunction. is this right?


p0325 is, ignition system or misfire, could be plugs, wires, or a bad coil. p1126 throttle control motor relay curcuit open.P1126 Power supply for the throttle control motor is provided to the ECM via throttle control motor relay. The throttle control motor relay is ON/OFF controlled by the ECM. When the ignition switch is turned ON, the ECM sends an ON signal to throttle control motor relay and battery voltage is provided to the ECM. When the ignition switch is turned OFF, the ECM sends an OFF signal to throttle control motor relay and battery voltage is not provided to the ECM. possible cause, Harness or connectors (Throttle control motor relay circuit is open Throttle control motor relay.

May 07, 2010 | 2000 Nissan Altima

1 Answer

What those code p1441 manufacturer control auxiliary emission controls mean


what you want to do is take it to nissan and scan it with the consult2 diagnostic system to tell you which of the many things in the system have failed.
the EGR is the most common.

May 28, 2009 | 2001 Nissan Xterra

Not finding what you are looking for?
1998 Nissan Altima Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...