Question about 2007 Mitsubishi Grandis 2.0

Open Question

I changed the battery in my key now the central locking doesn't work I have to unlock and lock it manually

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

extreme7528
  • 108 Answers

SOURCE: I just bought a 2006 mitsubishi otlander and the

Take it to the dealer and have the key fob re-coded. Sounds like it lost it code for whatever reason.

Posted on Oct 07, 2009

  • 4793 Answers

SOURCE: key less entry stopped working

poss low charge in battery in keys..... nearer you get lower the battery life.....

Posted on Feb 23, 2010

Suzman
  • 642 Answers

SOURCE: My Mitsubishi colt CZ1 (07

Central locking works by way of little electric motors that engages and disengages the door lock. The drivers door has an additional set of contacts in the actuator which signal the controller when it changes position. The controller activates the servo motors when a signal is received from the receiver or from the drivers door servo motor. So in your case I suspect the motor part of the drivers door actuator is done for.
To replace you will have to remove the inner driver's door panel to get at the actuator. The actuator itself cannot be repaired and needs to be replaced as a unit.

Posted on Apr 29, 2011

Testimonial: "Very helpful answer and a prompt response. Thanks"

alicantecoli
  • 22114 Answers

SOURCE: I changed the lock actuator on my 2004 mitsubishi endeavor, but the key fob will not work on that door

check the wires in the rubber boot between the door pillar and the door for a break in the wire or loose plug socket ,check for a feed to the lock with a multimeter as well whilst operating the system as i think this is your problem here -no power

Posted on Feb 25, 2012

carmedic310
  • 37 Answers

SOURCE: Mitsubishi colt 2005 driver door will not unlock with or without key

if the electric door lock actuator froze up this could cause the problem as it would not want to unlock either way it is inside the door panel hooked to the door latch

Posted on Jun 07, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can the immobilizer or central locking be switched off in a Nissan Almeria 2001 car?


you can remove the central locking fuse , this will stop the lock/unlock constantly , the problem is usually with the drivers door lock mechanism , that is perhaps why you cant lock/unlock with the key, lock from inside vehicle and get out passenger side, that lock should work with the key until you get the lock changed on drivers door

Jun 11, 2015 | Nissan Almera Cars & Trucks

1 Answer

Alarm went off, now the central locking doesn't work


use the car key itself from outside the vehicle with everything closed: use key in drivers door outside door lock and manually lock and unlock the door. check if fixed, may have to do a few times. i do believe the vehicle is in theft mode.

Aug 18, 2012 | 1994 Volkswagen Golf

1 Answer

Central locking wiring clio


I had a problem where my key fob did not lock or unlock the car, Renault Clio Dynamique, but the central locking button in the car did still work and engine turned over fine. Changed the key fob battery still nothing. Read online about disconnecting and reconnecting the car battery, (negative only) and hey presto it worked! All working fine now!

May 13, 2012 | 2002 Renault Clio

1 Answer

Central locking in my bmw 320 diesel isnt working it wont open the doors but it will start the engine , the spare key is the same so its not the battery of the keys


Providing central locking works when you insert key in lock,try programming keys
Enter car make sure all doors/windows are shut
Switch ignition on and off,remove key
PRESS AND HOLD UNLOCK BUTTON ON KEY
Press lock button on key 3 times whithin 10 seconds and release unlock
Central locking will lock/unlock rapidly to confirm reset
If your key is the type with bmw logo in the middle battery replacement is not possible,as it charges as you drive

Jun 21, 2010 | 2004 BMW 3 Series

1 Answer

Central locking will not work on remote key.


unlock car with key/hold over for 30 secs then lock car with key/hold over for 30 secs then unlock with remote hold button down for 30 secs.this should reset system.

Apr 28, 2010 | 1998 Audi A4

2 Answers

The doors do not open by remote control key(BMW 740il 1996 model)


Programming
When
Key batteries completely discharged. Key batteries not replaced within 60 seconds. Key added or replaced. DO NOT press remote control buttons during battery replacement.
How
Unlock vehicle. Enter vehicle. Close driver's door. Switch ignition ON and OFF. Remove ignition key. Press and hold unlock button Fig. 1 [1]. Press lock button Fig. 1 [2] briefly 3 times within 10 seconds keeping unlock button [1] depressed. Release unlock button Fig. 1 [1]. Some models: LED Fig. 1 [3] flashes slowly for 10 seconds. Some models: Central locking system locks and unlocks rapidly to indicate correct programming. Some models: Repeat above procedure if central locking system does not work and LED does not flash or LED flashes continuously

To change batteries remove panel back of key then screws on plastic bar
Batteries are available from your local motor factor shop
You might not need new batteries try re programing as described above

Apr 24, 2010 | 1998 BMW 7 Series

2 Answers

2002 bmw 530i key does not (remotely) unlock doors or trunk but they work fine manually.


Unlock vehicle. Enter vehicle. Close driver's door. Switch ignition ON and OFF. Remove ignition key. Press and hold unlock button. Press lock button briefly 3 times within 10 seconds keeping unlock button depressed. Release unlock button. Some models: LED flashes slowly for 10 seconds. Some models: Central locking system locks and unlocks rapidly to indicate correct programming. Repeat above procedure if central locking system does not work and LED does not flash or LED flashes continuously.

Mar 09, 2010 | 2002 BMW 5 Series

2 Answers

Hi, I have an imported 2004 Subaru Impreza WRX. How do I reprogram the key fob after changing the battery.


first unlock car manually with key remove driver side kick panel/lower A pillar trim connect locking registration wires together(two white connectors,black wire and black and blue wire)press and hold central locking switch on drivers door in the unlock position .interior lamp will flash and an acoustic sound will be heard. now get your key and press unlock and then lock the door should lock then unlock, job done ,i persume it was to program the fob to work the central locking u wanted

Jan 17, 2010 | 2001 Subaru Impreza

3 Answers

Peugeot 307 1.6 petrol central locking problem


leave ign off with key out 3mins disconnet battery 5 mins reconnett and press lock/ unlock repeatedly until locks cycle through to re sync try this any probs come back to me

Dec 25, 2008 | 2005 Peugeot 405

Not finding what you are looking for?
2007 Mitsubishi Grandis 2.0 Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8140 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...